Newport Electronics INFINITY Series User manual

INFCR and INFCR-xxxB
INFINITY®C Programmable Digital
RTD Meter
Operator’s Manual
®
NEWPORT Electronics, Inc.

Counters
Frequency Meters
PID Controllers
Cloc /Timers
Printers
Process Meters
On/Off
Controllers
Recorders
Relative
Humidity
Transmitters
Thermocouples
Thermistors
Wire
Rate Meters
Timers
Totalizers
Strain Gauge
Meters
Voltmeters
Multimeters
Soldering Iron
Testers
pH pens
pH Controllers
pH Electrodes
RTDs
Thermowells
Flow Sensors
For Immediate Assistance
In the U.S.A. and Canada: 1-800-NEWPORT
®
In Mexico: (95) 800-NEWPORT
SM
Or call your local NEWPORT Office.
Internet e-mail
[email protected]
Additional products from
NEWPORTnetSM On-Line Service
http://www.newportUS.com
®
NEWPORT Electronics, Inc.
It is the policy of NEWPORT to comply with all worldwide safety and EMC/EMI regulations that apply. NEWPORT is constantly pursuing
certification of its products to the European New Approach Directives. NEWPORT will add the CE mar to every appropriate device upon
certification.
The information contained in this document is believed to be correct but NEWPORT Electronics, Inc. accepts no liability for any errors it
contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected applications.
TRA EMARK NOTICE:
a
®
,,, newportUS.com, , ,
and the “Meter
Case Bezel Design”
are trademar s of NEWPORT Electronics, Inc.
PATENT NOTICE: This product is covered by one or more of the following patents: U.S. Pat. No. Des. 336,895; 5,274,577; 6,243,021 /
Canada 2052599; 2052600 / Italy 1249456; 1250938 / France Brevet No. 91 12756 / Spain 2039150; 2048066 / UK Patent No. GB2 249 837;
GB2 248 954 / Germany DE 41 34398 C2. Other US and International Patents Pending.
N
EWP
O
RT
®
NEWP
O
RT
®
This device is mar ed with the international caution symbol. It is important to read the Setup Guide before installing or commissioning
this device as it contains important information relating to safety and EMC.

i
PREFACE
Manual Objectives
This manual shows you how to set up and use the Programmable Digital RTD Meter.
Standard Procedures:
* Chec ing voltage jumpers, or changing voltage power
* Mounting the panel
* Selecting the input type
* Selecting a decimal point position
* Setting the setpoint's active band
* Selecting a latched or unlatched operation
* Setting setpoint deadbands
* Enabling/disabling setpoint changes
* Enabling/disabling the RESET button in the run mode
Optional Procedures:
* Setting input resolution
* Enabling/disabling analog output
* Selecting analog output as current or voltage
* Selecting analog output or proportional control
* Selecting proportional band
* Using manual reset (offsetting setpoint errors)
* Scaling analog output

Table of Contents
Section Page
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2. ABOUT THE METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.2 STANDARD FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.3 AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.4 FRONT OF THE METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.5 REAR OF THE METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.6 CONDITIONS REQUIRING DISASSEMBLY . . . . . . . . . . . . . . . . . . . .10
3. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.1 RATING/PRODUCT LABEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2 MAIN BOARD POWER JUMPERS . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.3 PANEL MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.4 CONNECTING SENSOR INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.5 CONNECTING MAIN POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
3.6 ANALOG AND RELAY OUTPUT CONNECTIONS . . . . . . . . . . . . . . . .17
4. CONFIGURING THE METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.1 SELECTING THE INPUT TYPE (INPT) . . . . . . . . . . . . . . . . . . . . . . . .19
4.2 DECIMAL POINT POSITION (DEC.P) . . . . . . . . . . . . . . . . . . . . . . . . .19
4.3 READING CONFIGURATION ("RD.CF") . . . . . . . . . . . . . . . . . . . . . . .20
4.4 COLOR CONFIGURATION (“COLR”) . . . . . . . . . . . . . . . . . . . . . . . . . .20
4.5 SETPOINT 1 CONFIGURATION (S1.CF) . . . . . . . . . . . . . . . . . . . . . .21
4.6 SETPOINT 2 CONFIGURATION (S2.CF) . . . . . . . . . . . . . . . . . . . . . .22
4.7 SETPOINT 1 DEADBAND (S1.DB) . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.8 SETPOINT 2 DEADBAND (S2.DB) . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ii

Table of Contents
4.9 OUTPUT CONFIGURATION (OT.CF) . . . . . . . . . . . . . . . . . . . . . . . . .23
4.9.1 To Enable or Disable The Analog Output . . . . . . . . . . . . . . . . . .23
4.9.2 To Select Analog Output as Current or Voltage . . . . . . . . . . . . . .24
4.9.3 To Select Analog Output or Proportional Control . . . . . . . . . . . .24
4.10 PROPORTIONAL BAND (P.BND) . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4.11 MANUAL RESET (M.RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4.12 OUTPUT SCALE AND OFFSET (OT.S.O) . . . . . . . . . . . . . . . . . . . . .27
4.13 RTD TEMPERATURE OFFSET (T.OFF) . . . . . . . . . . . . . . . . . . . . . .29
4.14 LOCK OUT CONFIGURATION (LK.CF) . . . . . . . . . . . . . . . . . . . . . . .30
4.14.1 To Enable or Disable Setpoint Changes . . . . . . . . . . . . . . . . . .30
4.14.2 To Enable or Disable the RESET button in the Run Mode . . . .30
4.14.3 To Enable Display’s Program Version . . . . . . . . . . . . . . . . . . . .30
4.15 BRIGHTNESS CONFIGURATION (bRit) . . . . . . . . . . . . . . . . . . . . . .31
4.16 TUNING PROPORTIONAL CONTROLLER (TUNE) . . . . . . . . . . . . . .31
5. DISPLAY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
6. MENU CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7. SETPOINT CONFIGURATION DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
8. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
9. FACTORY PRESET VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
CE APPROVAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
iii

Table of Contents
List of Figures
Figure Page
Figure 2-1. Front-Panel with “Big” LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Figure 2-2. Front-Panel with Standard LED Display . . . . . . . . . . . . . . . . . . . . . . . . .5
Figure 2-3. Connector Label (AC-Powered and DC-Powered Detail) . . . . . . . . . . . .8
Figure 3-1. Main Board Power Jumpers (W1, W2, W3) . . . . . . . . . . . . . . . . . . . . .11
Figure 3-2. Main Board Jumper Positions (6 S2 Pins) . . . . . . . . . . . . . . . . . . . . . .12
Figure 3-3. Upper Option Board Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Figure 3-4. Meter - Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Figure 3-5. Panel Cut-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Figure 3-6. 2-Wire RTD Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 3-7. 3-Wire RTD Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 3-8. 4-Wire RTD Input connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Figure 3-9. Main Power Connections - AC Powered Unit . . . . . . . . . . . . . . . . . . . .16
Figure 3-10. Main Power Connections - DC Powered Unit . . . . . . . . . . . . . . . . . . .17
Figure 3-11. Analog Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 3-12. Relay Output Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 3-13. Isolated Analog Output Connections. . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 4.1 Proportional Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 8-1. Meter Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
List of Tables
Table Page
Table 2-1. Accessories and Add-Ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Table 2-2. Rear Connector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Table 3-1. S3 Jumper Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Table 3-2. Main Power Connections - AC Powered Unit . . . . . . . . . . . . . . . . . . . . .16
Table 5-1. Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Table 6-1. Menu Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Table 6-2. Front Panel Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Table 6-3. Run Mode Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Table 7-1. Setpoint Configuration Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Table 9-1. Factory Preset Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
iv

Table of Contents
NOTES, WARNINGS and CAUTIONS
Information that is especially important to note is identified by these labels:
• NOTE
• WARNING
• CAUTION
• IMPORTANT
NOTE: provides you with information that is important to successfully setup and use
the Programmable Digital Meter.
CAUTION or WARNING: tells you about the ris of electric shoc .
CAUTION, WARNING or IMPORTANT: tells you of circumstances or practices that
can effect the meter's functionality and must refer to accompanying documents.
Note
☞
vv

vivi

SECTION 1. INTRO UCTION
1.1 UNPACKING
Remove the Pac ing List and verify that all equipment has been received. If there are any
questions about the shipment, use the phone numbers listed on the bac cover to contact the
Customer Service Department nearest you.
Upon receipt of shipment, inspect the container and equipment for any signs of damage. Ta e
particular note of any evidence of rough handling in transit. Immediately report any damage to
the shipping agent.
The carrier will not honor any claims unless all shipping material is saved for their
examination. After examining and removing contents, save packing material and
carton in the event reshipment is necessary.
Verify that you receive the following items in the shipping box:
QTY ESCRIPTION
1 Indicator/controller with all applicable connectors attached.
1 Owner's Manual
1 Set Mounting brac ets
1 Quic Start Manual
If you ordered any of the available options (except the " L" lank Lens option), they
will be shipped in a separate container to avoid any damage to your
indicator/controller.
1
1
Note
☞
Note
☞

1Introduction
1.2 SAFETY CONSI ERATIONS
This device is mar ed with the international caution symbol. It is important to read
this manual before installing or commissioning this device as it contains important
information relating to Safety and EMC (Electromagnetic Compatibility).
This instrument is a panel mount device protected in accordance with Class I of
EN 61010 (115/230 AC power connections), Class III for the DC Voltage Power Option
(10-32 Vdc). Installation of this instrument should be done by Qualified personnel. In order to
ensure safe operation, the following instructions should be followed.
This instrument has no power-on switch. An external switch or circuit-breaker shall
be included in the building installation as a disconnecting device. It shall be mar ed to
indicate this function, and it shall be in close proximity to the equipment within easy
reach of the operator. The switch or circuit-brea er shall not interrupt the Protective
Conductor (Earth wire), and it shall meet the relevant requirements of IEC 947–1 and
IEC 947-3 (International Electrotechnical Commission). The switch shall not be
incorporated in the mains supply cord.
Furthermore, to provide protection against excessive energy being drawn from the
mains supply in case of a fault in the equipment, an overcurrent protection device
shall be installed.
• Do not exceed voltage rating on the label located on the top of the instrument housing.
• Always disconnect power before changing signal and power connections.
• Do not use this instrument on a wor bench without its case for safety reasons.
• Do not operate this instrument in flammable or explosive atmospheres.
• Do not expose this instrument to rain or moisture.
• Unit mounting should allow for adequate ventilation to ensure instrument does not
exceed operating temperature rating.
• Use electrical wires with adequate size to handle mechanical strain and power
requirements. Install without exposing bare wire outside the connector to minimize
electrical shoc hazards.
EMC Considerations
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wires close to the instrument if EMC
problems persist.
Failure to follow all instructions and warnings may result in injury!
Note
☞
2

3
SECTION 2. ABOUT THE METER
2.1 ESCRIPTION
The Resistance Temperature Detector (RTD) meter is a value pac ed indicator/controller. Four
full digits accurately display your temperature. Select from 2, 3 or 4 wire input configuration. Your
meter may be a basic indicator or it may include analog output or dual relay output. Analog or
dual relay output must be ordered at time of purchase. Analog output is fully scalable and may be
configured as a proportional controller, or to follow your display. Dual 5 amp, form C relays
control critical processes. Front panel pea detection and memory is also standard. A mechanical
loc out has been included to guard against unauthorized changes.
2.2 STAN AR FEATURES
The following is a list of features:
* 4-digit, three color programmable “Big” LED display
or 4-digit, Standard LED Display
* ±0.5° C accuracy
* Pea detection
* Non-volatile memory-no battery bac up
* 115 or 230 V ac 50/60 Hz power supply
or 10-32 Vdc
The following is a list of optional features
* Dual 5 amps, form C relay outputs
* Scalable analog output
* Proportional control
* Front-panel deviation correction
* Easy setup for proportional control
Features with are for the “B” version which has three-color programmable
“Big” LED display - All segment characters shown are for the “B” version.
2

2About The Meter
2.3 AVAILABLE ACCESSORIES
Table 2-1. Accessories and Add-Ons
Add-On Options
FS Special Calibration/Configuration
SPC4 NEMA-4 Splash Proof Cover
SPC18 NEMA-4 Splash Proof Cover, NEW
Accessories
TP1A Trimplate panel adaptor.
Adapts DIN1A/DIN2A cases to larger panel cutouts
RP18 19-In. Rac Panel for one (1) 1/8 DIN instrument
RP28 19-In. Rac Panel for two (2) 1/8 DIN instrument
RP38 19-In. Rac Panel for three (3) 1/8 DIN instrument
4

5
About The Meter
2.4 FRONT OF THE METER
Figure 2-1 shows each part of the front of the three-color programmable
“Big” LED display meter (Version B).
Figure 5-1. Front-Panel with Big isplay
Figure 2-2 shows each part of the front of the standard LED display meter.
Figure 5-2. Front-Panel wtih Standard isplay
These meter display windows (both versions) light when appropriate:
1- Setpoint 1 status
2- Setpoint 2 status
C- °C unit indicator
F- °F unit indicator
5 Pushbuttons for programming the meter.
//
䊱䊳
••••
12
RESETMENU
DEVMAXSETPTS
CF
2
igital LE isplay:
- 1.9.9.9 or 9.9.9.9 4-digit
three color programmable,
21 mm (0.83") high LED
display with programmable
decimal point.
igital LE isplay:
- 1.9.9.9. or 9.9.9.9.
14 segment, 13.8 mm
(0.54") high LED display
with programmable
decimal point.

2About The Meter
2.4 FRONT OF THE METER (Continued)
METER BUTTONS
SETPTS Button
This button functions only in the run mode. When the meter is in the run mode, press this button
to sequentially recall the previous setpoint settings. After using the 䊱/MAX and 䊳/ EV buttons
to alter these settings as desired, press the SETPTS button to store these new values.
Unless you press the SETPTS button within 20 seconds to store your input, the meter
will scroll to setpoint 2 and retain the last value stored.
If the dual relay option is not installed or if the “L.3=1” on the “LK.CF” menu, pressing the
SETPTS button will display the meter's firmware version.
䊱/MAX Button
During the run mode, press the 䊱/MAX button to recall the PEAK reading since the last press of
the RESET button. To return to the current readings without resetting the PEAK reading, press
the 䊱/MAX button. To reset the PEAK reading, press the RESET button.
During the configuration mode, use the 䊱/MAX button to change the values of the flashing digit
shown on the display and/or toggle between menu choices, such as "R.1=F" or "R.1=C". When
configuring your setpoint values, press the 䊱/MAX button to increment the flashing digit from
0 to 9 by 1's.
䊳/ EV Button
During the run mode press the 䊳/ EV button to display the deviation from setpoint 1.
When configuring your setpoint values, press the 䊳/ EV button to scroll to the next digit.
6
Note
☞

7
About The Meter
2.4 FRONT OF THE METER (Continued)
MENU Button
In the run mode, press the MENU button to terminate the current measuring process and enter
you into the configuration mode.
In the configuration mode, press the MENU button to store changes in the non-volatile memory
and then advance you to the next menu item.
RESET Button
If you hard reset or power off/on the meter, it shows "RST" followed by "RT ".
In the run mode, press the RESET button to reset the setpoints and display "SP.RS". If display
shows pea value, press the RESET button to reset pea value. Display shows "PK.RS".
In the configuration mode, press the RESET button once to review the previous menu. Pressing
the RESET button twice results in a hard reset and returns you to the run mode.
2

2About The Meter
2.5 REAR OF THE METER
Figure 2-3 shows the connector label mounted at the top of the meter housing. Table 2-2 gives a
brief description of each connector at the rear of the meter.
Figure 2-3. Connector Label (AC Powered and C Powered etail)
8
dc Connector
Label detail
Note
☞

9
About The Meter
2.5 BACK OF THE METER (Continued)
Table 2-2. Rear Connector escription
Connector escription
TB1-1 Setpoint 1: Normally open (N.O.1) connection
TB1-2 Setpoint 1: Normally closed (N.C.1) connection
TB1-3 Setpoint 1: Common (COM1) connection
TB1-4 Setpoint 2: Normally open (N.O.2) connection
TB1-5 Setpoint 2: Normally closed (N.C.2) connection
TB1-6 Setpoint 2: Common (COM2) connection
TB1-7 ac line connection (no connections on dc-powered units)
TB1-8 ac neutral connection (+ Input on dc-powered units)
TB1-9 ac Earth ground (-dc-power return on dc-powered units)
TB1-10 Analog 1 voltage output
TB1-11 Analog 2 current output
TB1-12 Analog 3 return
TB2-1 +E2: not used
TB2-2 +S2: not used
TB2-3 -S2: not used
TB2-4 -E2: not used
TB2-5 +E1: Positive excitation
TB2-6 +S1: Positive signal input
TB2-7 -S1: Negative signal input
TB2-8 -E1: Negative excitation
TB5-1 Isolated Analog Voltage Output
TB5-2 Isolated Analog Current Output
TB5-3 Isolated Analog Output Return
2

2About The Meter
2.6 ISASSEMBLY
You may need to open up the meter for one of the following reasons:
• To chec or change the 115 or 230 Vac power jumpers.
• To install or remove jumpers on the main board.
Disconnect the power supply before proceeding.
To remove and access the main board, follow these steps:
• Disconnect the main power from the meter.
• Remove the bac case cover.
• Lift the bac of the main board upwards and let it slide out of the case.
10
Note
☞

11
SECTION 3. GETTING STARTE
Caution: The meter has no power-on switch, so it will be in operation as soon you
apply power.
If you power off/on the meter, or perform a hard reset (press the RESET button twice), the meter
shows "RST", followed by "RT ".
3.1 RATING/PRO UCT LABEL
This label is located on top of the meter housing (Refer to Figure 3-4).
3.2 MAIN BOAR POWER JUMPERS
Important: If you want to change the Factory preset jumpers, do the following steps;
otherwise go to section 3.3.
Warning: Disconnect the power from the unit before proceeding. This device must
only be reconfigured by a specially trained electrician with corresponding
qualifications. Failure to follow all instructions and warnings may result in injury!
To chec voltage jumpers, or to change from 115 V to 230 V ac:
1. Remove the main board from the case. Refer to Section 2.6.
2. Locate the solder jumpers W1, W2, and W3 (located near the edge of the main board
alongside the transformer - refer to Figure 3-1).
3. If your power requirement is 115 V ac, solder jumpers W1 and W3 should be wired,
but jumper W2 should not. If your power requirement is 230 V ac, solder jumper W2
should be wired, but jumpers W1 and W3 should not.
Figure 3-1 shows the location of solder jumpers W1 through W3 on the main board.
Figure 3-1. Main Board Power Jumpers (W1, W2, W3)
3

3Getting Started
3.2 MAIN BOAR POWER JUMPERS (Continued)
Figure 3-2 shows the main board jumpers.
Figure 3-2. Main Board Jumper Positions (6 S2 Pins)
Figure 3-3. Upper Option Board Installation
P1
TB5
Attach cable
to P1.
12