Sensitech TEMPTALE ULTRA BLE User manual

USER MANUAL
For
TEMPTALE ULTRA BLE
NOTICE OF PROPRIETARY PROPERTY
This document and the information contained in it are the proprietary property of Sensitech. It may not be copied or used
in any manner nor may any of the information in or upon it be used for any purpose without the express written consent of
an authorized agent of Sensitech Inc.

REVISION HISTORY:
REV
DESCRIPTION
DWN
APVD
DATE
2
Initial Release
JZL
TNS
03AUG21
3
Updated Disclaimer; Remove Watermark Draft stamp
JZL
TNS
16SEPT21
4
Updated FCC and IC Disclosure
JZL
TNS
20SEPT21
5
Updated Radiation Exposure
JZL
TNS
23SEPT21

© SENSITECH INC. Page 3 of 9
T11012820 User Manual
Table of Contents
1. Introduction...............................................................................................................4
1.1. Purpose ......................................................................................................... 4
1.2. Scope.............................................................................................................4
1.3. Description.....................................................................................................4
1.4. Radio Frequency Characteristics................................................................... 4
1.4.1. Operating Frequencies................................................................. 4
1.5. Output Power Characteristics ........................................................................ 4
1.5.1. Output Power ...............................................................................4
2. Physical Appearance................................................................................................5
2.1. User Interface ................................................................................................5
2.1.1. LEDs............................................................................................. 5
2.1.2. Buttons......................................................................................... 5
2.1.3. LCD..............................................................................................6
3. Using the Device ......................................................................................................7
3.1. Starting the device:........................................................................................ 7
3.2. Stopping the device: ...................................................................................... 7
4. Software ...................................................................................................................7
5. Disclaimers...............................................................................................................8
5.1. FCC ...............................................................................................................8
5.1.1 FCC Radiation Exposure Statement.....................................................9
5.2. IC................................................................................................................... 9
5.2.1. IC Radiation Exposure Statement ................................................9
5.3. CE.................................................................................................................. 9

© SENSITECH INC. Page 4 of 9
T11012860 User Manual
1. Introduction
1.1. Purpose
This document describes the usage of a TEMPTALE ULTRA BLE device.
1.2. Scope
The intended audience is a valued customer.
1.3. Description
The TEMPTALE ULTRA BLE is a BLE enabled sensor data logger designed for the
transportation industry. It is primarily intended to be used to record and store accurate
temperature data as well as transmit the data to a Bluetooth enabled smart phone or tablet
device via a mobile application. The device also supports secondary legacy download
mechanism as well utilizing a USB file system to auto generate a PDF when plugged into a
computer.
The following is a brief summary of its features:
1. BLE 5.1 Enabled
2. Internal battery
3. Temperature Sensor
4. USB for secondary download
5. LCD Display
6. User Interface
Manufacturer Information
Company Name: SENSITECH Inc.
Address: 800 Cummings Center, Beverly, MA USA
Importer Information
Company Name: XXXXXXXXXX
Address: XXXXXXXXXXXXX
1.4. Radio Frequency Characteristics
1.4.1.Operating Frequencies
2.4GHZ
1.5. Output Power Characteristics
1.5.1.Output Power
0 dbm

© SENSITECH INC. Page 5 of 9
T11012860 User Manual
2. Physical Appearance
2.1. User Interface
The user interface consists of the following:
1. Three LEDs (red, green, blue)
2. Two buttons(Start/Stop)
3. One LCD Display
2.1.1.LEDs
The LEDs are intended to allow quick and easy-to-read status to be conveyed to the
end user. The user can immediately know the status of the unit during startup and
operation.
2.1.1.1. System Startup Sequence
During startup, and If configured the Green LED blinks at 1hz for 4 secs.
2.1.2.Buttons
There are two buttons on the device:
1. Start –a configurable press delay is added, usually configured to be held for
three second before it starts.
2. Stop–a configurable press delay is added usually configured to be held for
three seconds before it stops.

© SENSITECH INC. Page 6 of 9
T11012860 User Manual
2.1.3.LCD
There is a LCD on the device:
During Startup, if there is a hardware failure found during the self-test, a X will
display on the LCD and the Stop sign will appear.

© SENSITECH INC. Page 7 of 9
T11012860 User Manual
3. Using the Device
3.1. Starting the device:
To start the device, press the START button. If the Start Key feature is enabled, the START
button must be held down for 3 seconds. The device may only be started from sleep mode.
3.2. Stopping the device:
There are 2 methods for stopping the device.
1. To stop the device, press the STOP button. If the Stop Key feature is enabled, the STOP
button must be held down for 3 seconds to stop.
2. In enabled, Plug the Monitor into a USB port on a computer or printer.
4. Software
This unit reports data over a BLE connection via mobile app. This data is accessible via several
web-based platforms that target various industries. Please contact customer support for more
information.

© SENSITECH INC. Page 8 of 9
T11012860 User Manual
5. Disclaimers
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that
can result in an explosion
Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or the leakage of flammable liquid or gas
A battery subjected to extremely low air pressure that may result in an explosion or the leakage
of flammable liquid or gas.
Do not dispose battery along with household waste.
There are no user serviceable parts inside, battery cannot be replaced by the end user, and will
result in damaging the device.
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
5.1. FCC
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the device.
2. Increase the separation between the equipment and device.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) This device must
accept any interference received, including interference that my cause undesired operation.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the device.

© SENSITECH INC. Page 9 of 9
T11012860 User Manual
5.1.1 FCC Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
This equipment complies with FCC and Canada radiation exposure limits set forth for
an uncontrolled environment.
5.2. IC
This device complies with Industry Canada RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the
device.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Leprésent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio
Exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le
fonctionnement.
5.2.1.IC Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou
un autre émetteur.
This equipment complies with FCC and Canada radiation exposure limits set forth for
an uncontrolled environment.
Cet équipement est conforme aux limites d’exposition aux radiations définies par le
Canada pour des environnements non contrôlés.
5.3. CE
The full text of the EU declaration of conformity is available upon request.