Nexcom NPT-5851 User manual

User Manual
Version V1.0 AUG 2012
NPT-5851

1
Copyright 2012
All Rights Reserved
Manual Version 1.0
Model Number: NPT-5851
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. We
shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
2nd generation Intel® Core™ brand are registered trademarks of
Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft
Corporation.
Other names and brands may be claimed as the property of others.

2
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power
switch and remove the power cord plug from the wall socket.
2. The wall socket must be easily accessible and in close proximity to the machine.
3. Read these instructions carefully. Save these instructions for future reference.
4. Follow all warnings and instructions marked on the product.
5. Do not use this product near water.
6. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
7. Slots and openings in the cabinet and the back or bottom are provided for ventilation
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should never be placed near or over a radiator or
heat register or in a built-in installation unless proper ventilation is provided.
8. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or local
power company.
9. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
10. Never push objects of any kind into this product through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or electric
shock.
11. Never spill liquid of any kind on the product.

3
CE MARK .
This device complies with the requirements of the EEC directive
2004/108/EC with regard to “Electromagnetic compatibility” and
2006/95/EC “Low Voltage Directive”
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
LEGISLATION AND WEEE SYMBOL
2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms
and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

4
Revision History
Changes to the original user manual are listed below:
Version Date Description
1.0 AUG. 2012  Initial release

5
Table of Contents
1. Package Checklist…………….................................................................
1
1-1 Standard items……………………………………………………………………..
1
1-2 Optional items……………………………………………………………………...
1
2. System View………………………………………………………………......
2
3. System Assembly & Disassembly…………………………………………
4
3-1 Replace the HDD………………………………………………………………….....
4
3-2 Replace the Motherboard…………………………………………………………..
5
3-3 Replace the Inverter Board & Touch Board………………………………….....
6
3-4 Install & Uninstall the Filter…………………………………...............................
7
3-5 Install VFD & MSR (Optional)…………………………………............................
8
4. Specification…………………………………………………………………..
9
5. Jumper Settings………………………………………………………………
11
5-1 HM-651 Motherboard Layout………………………………………………………
11
5-2 Connectors Description…………………………………………………………….
12
5-3 Jumper Settings……………………………………………………………………..
13
5-4 Install a Cash Drawer………………………………………………………………..
14
6. BIOS Settings………………………………………………………………….
15
6-1 About BIOS Setup………………………………………………………………….. 15
6-2 Main….…………………………………………………………………………………
17
6-3 Advanced……………………………………………………………………………..
19
6-4 Chipset………………………………………………………………........................
31
6-5 Boot…………………………………………………………………………………….
36
6-6 Security………………………………………………………………………………..
37
6-7 Save & Exit……………………………………………………………………………
38
Appendix………………………………………………………………………….
39

1
1. Package Checklist
1-1 Standard items
a. System b. power adapter
1-2 Optional items
d. VFD e. driver bank/e-User Manual f. power cord
b. Second Display (Pole Type)a. Second Display c. MSR

2
2. System View
No. Description
8 VFD (OPTION)
9 System Box (Inside with Motherboard)
10 Vesa Cover
11 Cables outlet
No. Description
1 Touch Screen
2 MSR/2-in-1 MSR (Option)
3 Power Button & Power LED
4 Model No. Label & OS License Label
5 Stand
6 Cables outlet
7 Heat sink
Top View
Front View Rear View
Side View

3
No. Description
1 DC 19V IN
2 Cash Drawer Port
3 USB (x4)
4 LAN (10/100/1000)
5 COM(x4)
6 2nd VGA
7 DC 12V OUT
8 2.5 HDD
9 Parallel port
10 Line OUT
Rear I/O View

4
3. System Assembly & Disassembly
3-1 Replace the HDD
c. d.
a. Unfasten the screws (x2) to remove the HDD cover.
b. Disconnect the HDD Cable and take out the HDD with HDD metal handle.
c. Unfasten the screws (x4) at both sides of HDD metal bracket.
d. Slide out the HDD from the HDD metal bracket and replace the HDD.
a. b.

5
3-2 Replace the Motherboard
To replace the motherboard, please follow the below steps:
(1) Disconnect the HDD cable from the motherboard (Chapter 3-1, step a,b)
(2) Open the system box to access the motherboard (See below)
a. Unfasten the screws(x11) on the back of system box.
b. Press the Front bezel then separate top and bottom chassis(L1、L2).
c. Remove the LCD rear cover.
d. Unfasten the screw(x8) fixing the motherboard and heatsink.
e. Unfasten the screw(x4) fixing the motherboard.
f. cable unplug out the motherboard with metal I/O bracket.

6
3-3 Replace the Inverter Board & Touch Board
3-3-1 Replace the Inverter Board
a. The location of Inverter board on the LCD sheet metal bracket.
b. Unfasten the screws (x2).
c. Disconnect the cables (x3).
3-3-2 Replace the Touch Board
a. The location of touch board on the LCD sheet metal bracket.
b. Unfasten the screws (x2).
c. Disconnect the cables (x2).

7
3-4 Install & Uninstall the Filter
The device uses a filter that is washable and reusable. Insert the filter inside the pocket in the
rear cover bracket, the handle backward the device and secure the filter with socket hole.
Draw out the filter from the pocket in the rear cover bracket (Tip: get the snap out of the socket
hole first)

8
3-5 Install VFD & MSR (Optional)
3-5-1 VFD install
a. Unfasten the screws.
b. Install VFD Module on the rear cover.
c. Tighten the screws.
3-5-2 MSR install
c. Install the MSR Module
on the rear cover.
d. Tighten the screws.
a. Unfasten the screws. b. Pull the MSR cover from rear cover.

9
4. Specification
Model Name NPT-5851
Motherboard NP-HM651
Processor
Default: Intel® Pentium® Processor B940, 2C/2T, 2.0 GHz, 2MB Cache;
Upgrade Optional: B950, 2C/2T, 2.10GHz, 2MB Cache; or
2nd Generation Intel® Core Mobile Processor:
i7-2710QE, 4C/8T, BF_2.1GHz/ 1CT_3.0GHz/ 2CT_2.9GHz, 6MB Cache.
i5-2510E, 2C/4T, BF_2.5GHz/ 1CT_3.1GHz/ 2CT_3.0GHz, 3MB Cache.
i3-2330E, 2C/4T, BF_2.2GHz, 3MB Cache.
Optional: Intel® Celeron® Processor B810, 2C/2T, 1.60 GHz, 2M Cache.
Chipset Intel® vPro™ Technology
Intel® Active Management Technology 7.0 paired with QM67 chipset.
PCH Default: Intel® BD82HM65 Platform Controller Hub, BD82HM65, FCBGA 989
Option: Intel® BD82QM67 Platform Controller Hub, BD82QM67, FCBGA 989
System Memory Default: 1 x SO-DIMM DDR3 1333 2GB;
Optional: 2 x SO-DIMM DDR3 1600 Maximum up to 8GB
Graphic Memory Integrated graphics controller, Intel® HD Graphics 3000
LCD / Touch Panel
LCD Size 15” TFT XGA (1024x768) 250cd/m² LCD panel
Touch Screen 15" 5-wire Resistive Zero Bezel Touch Panel
Tilt Angle 0° ~ 80°
Storage Device
Hard Drive 1 x 2.5" SATA HDD 320GB 5,400rpm
Expansion
mini-PCIe 1 x mini-Card slot (mini-PCIe / USB)
Rear I/O
Serial port 4 x RS-232
USB port 4 x USB 2.0
Parallel port 1 x Parallel
LAN Port 1 x RJ-45 (10/100/1000Mbps Ethernet)
VGA 1 x VGA
Cash Drawer Port 1 x RJ-11, support 2 cash drawers (24V, Max 1.1A)
DC-IN Jack 1 x 19V-IN
DC-OUT Jack 1 x DC-12V Output for 2nd Display Power (12V, Max 3.0A)
Line-OUT 1 x Line-OUT for Audio
Audio

10
System Buzzer 1 x System Buzzer
Internal Speaker 1 x 3W Speaker
System Control/ Indicator
Power Switch 1 x Power ON/OFF switch
Power LED 1 x Power ON LED (Green)
Power
Power Supply External AC-DC 19V/ 6.31A 120W Power Brick
Peripheral (Optional)
MSR ISO 3 Tracks MSR (USB or PS/2)
Customer Display 2 x 20 VFD customer display
2nd Display 15" LCD monitor
Certificate
EMC & Safety FCC Class A / CE / LVD
Environment
Operating Temperature 0°C ~ 40°C (32°F ~ 104°F)
Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)
Operating Humidity 20% - 80% RH non-condensing
Storage Humidity 20% - 85% RH non-condensing
Dimension
80° tilt angle 366(W) x 331(H) x 210(D) mm (No MSR) /
419(W) x 331(H) x 210(D) mm (w/ MSR)
Display Head 366(W) x 280(H) x 64.5(D) mm (No MSR) /
419(W) x 280(H) x 64.5(D) mm (w/ MSR)
Footprint 249 (W) x 209 (D) mm
Package Size 490(L) x 390(W) x 350mm(H) (No MSR) /
560(L) x 390(W) x 350mm(H) (w/ MSR)
Weight
Net Weight 8.0kg (17.6lbs)
Gross Weight 9.5kg (20.9lbs)
OS Support
Windows POSReady 2009,POS 7, Win 7 Pro, XP Pro, Win CE 6.0.
Linux 2.6 / 2.4 (Ubuntu, SuSE, Fedora, CENTOS 2.6 Only)

11
5. Jumper Settings
5-1 HM-651 Motherboard Layout

12
5-2 Connectors Description
Connector
Purpose Connector
Purpose
CN2 COM5 Internal connector CN3 SATA 3 Connector
CN4 COM6 Internal connector CN5 SATA 3 Connector
CN6 MINI PCI-E CN7 Sim card holder
CN8 LVDS Connector 48 Bit CN9 LVDS Connector 48 Bit
CN10 Line-out & MIC CN11 Print port
CN12 COM4 Internal connector CN13 VGA Connector
CN14 DC-Power Input Connector
CON1 MSR connector CON2 Power output connector
CON3 USB+LAN Connector CON4 CASH drawing connector
CON5 SATA POWER Connector
J1 Internal USB connector J2 Internal USB connector
J4 Power on SW J5 Reset SW
J6 Battery socket J7 CCFL Connector
J8 Keyboard connector J9 Speaker OUT
J10 4/5 Wire touch connector
JP1 SATA/HD/LAN/POWER LED
JP2 CMOS / ME Clear
JP4 Backlight voltage selection JP5 LCD Power selection
JP6 SDVO connector JP7 CASE OPEN Pin header

13
5-3 Jumper Settings
Panel Power selection:JP5
Function JP1 (1-2) (2-3)
◎3.3V
VCC 5V
◎Default setting 1-2 short.
CMOS CLEAR SIGNAL: JP2
Function JP1 (1-2) (2-3)
◎NORMAL
CLEAR CMOS
◎Default setting 1-2 short.
Note:

14
5-4 Install a Cash Drawer
You can install a cash drawer through the cash drawer port. Please verify the pin assignment
before installation.
Pin Signal
1 CASEOPEN2#
2 CASH1_P
3 CASEOPEN#
4 24V
5 CASH2_P
6 GND
Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Cash Drawer Pin Assignment