Nexersys N3 elite User manual

1
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
N3 Commercial Center Body Pad Conversion Instructions
June 2019
BEFORE YOU BEGIN
oPlease follow the manual for the most efficient assembly
oA power drill will speed up assembly
oEstimated assembly time is 30 minutes
Parts List:
A. Center Pad
B. Boot
C. Allen Wrench
D. String
E. Wrench
F. Plate
G. Washers & Nuts (x4)
H. Center Pad Board
Tools Required:
Screwdriver, Pliers, Power Drill (Recommended)

2
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
ASSEMBLY STEPS
Step 1: Unpack Parts
•Open the Conversion kit, remove the component and lay them out in a clear space
Step 2: Remove 3 and 5 Arm Assembly
•Unplug Tablet Cables from the back of Tablet
•Use Allen Wrench (C.) then unscrew and remove the Handle

3
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
•Remove Spine Extender
•Unplug Sensor chords (3)(4)(5) from AggPCB
•Unscrew 4 Allen keys for the 3 and 5 Arm Assembly
•Once unscrewed pull the Arm Assembly off ensuring no cables get torn or caught

4
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
Step 3: Remove the Center Body Pad and Boot
•Unplug Cord 4
•In the back, tie a long string to chord 4
•Using Wrench unscrew and remove the 4 Nuts connecting the Center Strike Pad and to
the Arm Assembly.
•Unplug cable connecting Center Strike Pad to the Pad Sensor

5
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
•Unscrew and remove the 4 Nuts connecting the Arm Assembly to Unit
•Remove Arm Assembly, pulling chords and string through
Step 4: Attach Center Boot
•Tie off the new Boot Cable with the string from the old boot cable so that it can be fed
back through the Spine and screw center boot to the back of machine

6
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
•Use Allen Wrench (C.) to screw bolts and washers (G.) to attach Boot (B.) to unit
•Using Allen Wrench, attach Plate (F.) using the 4 Washers and Nuts (G.) to backside of
unit
Step 5: Attach Center Body Pad
•Plug cable into the sensor in the back of Center Plate Board (H.)

7
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
•Use Washers and Nuts (G.) to attach center body pad to machine
•Attach Cord 4 the corresponding labeled 8 pinned connection on AggPCB
•Attach Micro USB into the AggPCB
•Place Dust Protector over the AggPCB

8
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
•Tuck Back into Spine Extender
•Place Spine Extended Cap back on unit, screw bolt and handle to spine extender, use
Allen Wrench (C.) to tighten
•Plug in tablet cables

9
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
Final Steps
•Log in as Admin (username: admin password: 1234)
•Select “Device Setup”
•Select corresponding device (either N3C or N3E)
•Select “Consumer”or “Commercial”
•Back out to main menu and begin your Workout!

10
XFit, LLC I 7500 Rialto Blvd Bldg. 1, STE 122 I Austin, TX 78735 I [phone]
Congratulations!
Your Conversion is Complete!