NEXhome DH-T101 Series User manual

Before the installation of the device, please check you have the following items on hand.
DH-T101 Series Quick Guide
2
|
Product Overview
PRODUCT OVERVIEW
1
|
Preparation
PREPARATION
MAKE PROPERTIES SAFER
AND SMARTER
1
Waterproof coverDH-T101 Screw
R3×6
×6
Screw
M4×15
×6
×1×1
160.0
①
②
③
④
⑤
⑥
⑦
355.0
27.0
25.0
9.0 114.0
294.0
① White light LED
② Infrared LED
③ RGB and Infrared camera
④ Touch Screen
⑤ Card Reader
⑥ Loudspeaker
⑦ Mic

MAKE PROPERTIES SAFER
AND SMARTER
2
DH-T101 Series Quick Guide
The device can be installed in both indoor and outdoor environment.
Outdoor installation: Avoid to exposing the device to direct sunlight, which will cause damage
to device and components due to high temperature.
Indoor installation: The device should be installed on somewhere 2 meters (6 feet) away from
light or 3 meters (9 feet) away from window/door.
3
|
Installation Environment
INSTALLATION ENVIRONMENT
4
|
Installation
INSTALLATION
 Flush Mounting
Backlight Direct sunlight Close to light
A. Dig out a hole on wall. Hole dimension(mm): 307.3(H)×121.9(W)×51(D)
B. Installation Height: Place the camera 1.5m (around 4ft 11in) away from the ground
STEP 1
307.3
TOP
51
121.9 43.5
230.0
90.0 51
37.0
66.0

MAKE PROPERTIES SAFER
AND SMARTER
3
DH-T101 Series Quick Guide
A. Lock the wall-mounting box on a Type86 bottom box with two M4×15 screws.
B. Lock the wall-mounting box on wall with four M4×15 screws.
C. Pull cables through the wall-mounting box and waterproof cover, then connect them to corresponding
interfaces of device. Lock the waterproof cover on device with four R3×6 screws.
D. Embed the device into wall-mounting box and adjust it until device sides run in alignment with the
vertical edges of wall, then lock the device from bottom with two R3×6 screws.
A. Put the embedded box into the dug hole and lock it with six M4×15 screws. Then fill the gap between
wall and embedded box with cement or non-corrosive adhesive.
B. Attach the adjusting bracket into the embedded box and lock it with six M4×15 screws.
C. Pull the cables through the embedded box, bracket and the waterproof cover, then connect them to
corresponding interfaces of device. Lock the waterproof cover on device with four R3×6 screws.
D. Hook the top of device with bracket and adjust it until device sides run in alignment with the vertical
edges of wall, then lock the device from bottom with two R3×6 screws.
 Wall Mounting
STEP 2
A
B
C
D

MAKE PROPERTIES SAFER
AND SMARTER
4
DH-T101 Series Quick Guide
+12VGNDGND 485B 485A
NODS GND SW NC COMGND
Exit Button Door LockDoor sensor
Elevator control device
Power
Network
5
|
Device Wiring
DEVICE WIRING
 Notes
Pin NO/COM is connected to the cathode lock
Pin NC/COM is connected to anode lock or magnetic lock.
A
B
C
D

MAKE PROPERTIES SAFER
AND SMARTER
5
DH-T101 Series Quick Guide
6
|
Specifications
SPECIFICATIONS
7
|
Configurations
CONFIGURATIONS
The system language and the network
setting can be selected and configured when
the initial booting of device.
 Initial Setup
Enter 9999 in Call menu then enter 3888 to get into
the Project Setting. Tap Network to check the IP
address.
 Check IP Address
Log into Web configuration portal of device,
set up and register SIP accounts in INTER-
COM-ACCOUNT page. (You can refer to
device user manual for more details)
 Set SIP Account
Select DTMF mode and configure the code in
SYSTEM-RELAY page of Web configuration portal.
(You can refer to device user manual for more
details)
 Set DTMF Code
8
|
Functions
FUNCTIONS
You can make calls from the device by select
contacts or dial call number
 Make Calls
Enter the access PIN set in device to unlock the
door.
 PIN Unlock
Incoming calls to T101 will be answered
automatically by default.
 Auto Answer
Walk in front of camera, the device can
recognize the face and unlock the door if
facial image is matched.
 Face Unlock
Press the configured DTMF code on keypad of
device answering the call, the lock connected on
T101 will be unlocked remotely.
 DTMF Unlock
Attach the saved access card or keyfob on the card
reader area of T101 to unlock the door.
 Card/Keyfob Unlock
 OS: Android
 Display: 10-inch IPS LCD
 Resolution: 1280×800
 Input power: DC12~15V 1.5A
 IP level: IP65
 Front panel: Aluminum
 Working Temperature: -30℃ ~ 70℃
 Working Humidity: 10%~95%RH
 Dimension:
355×160×27mm (Device Surface)
307.3×121.9×51mm (Flush Installation)

MAKE PROPERTIES SAFER
AND SMARTER
6
DH-T101 Series Quick Guide
Visual Angle
9
|
Precautions
PRECAUTIONS
 Violent vibration, collision and shock will cause damages to device.
 Intense direct sunlight will seriously affect the device performance and life span.
 Keep the access card/keyfob away from magnet and water. DO NOT fold or bend the card/keyfob.
 The height between camera and ground should be 1.5m (around 4ft 11in) to guarantee the ideal
visual angle.

Fujian Nexhome Intelligent Technology Co.,Ltd.
Notice Information
ADD: No.33 Xingang Avenue, Shangjie, Minhou, Fuzhou, Fujian, 350108, China
Web: www.nexhome.ai
Infromation contained in this document is believed to be accurate and reliable at the
time of printing. This document is subject to change without notice, The update vision
of this document can be viewed on NEXhome website: http://www.nexhome.ai
©Copyright 2022 NEXhome Ltd.All right reserved.