Next 763922 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0333 777 8999
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty.
Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-
763922 ,721139 SQUARE TO RECTANGLE TABLE
by-step instructions.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-
• Made from honeycomb board,particle board & MDF with a wood effect finish.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
PRODUCT INFORMATION
• Made in China
• For general cleaning, periodically dust with a soft cloth.
• Do not use furniture polish.
• Do not rub or scrub the surface when cleaning.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
CARE INSTRUCTIONS
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
Page 1 of 5

1. Insert 8 x bolts (C) into nuts fixed on panels 2 (x4) and turn
bolts (C) clockwise until tight by hands.
FITTINGS
PARTS
STEP ONE
1. Glue and insert 4 x wooden dowels (A) into
panel 3.
2. Attach panels 2 (x2) to panel 3 .
3. Slot 2 X metal pieces (D) onto bolts (C ) and thread
2 X springs (F) onto bolts (C ) then screw 2 X metal
nuts (E) with spanner (G) until tight.
STEP TWO
Page 2 of 5

1.Glue and insert 4 x wooden dowels (A) into
panel 6.
2. Attach panels 2 (x2) to panel 6 .
3. Slot 2 X metal pieces (D) onto bolts (C ) and thread
2 X springs (F) onto bolts (C ) then screw 2 X metal
nuts (E) with spanner (G) until tight.
4. Attach latch (J) on panel 6 with 2 x screws (K) using
screwdiver to tighten
1. Glue and insert 8 x wooden dowels (A) into
panels 3 (x2).
2. Attach the assembled leg frames to panels 3 (x2).
3. Slot 4 X metal pieces (D) onto bolts (C),and thread
4 X springs (F) onto bolts (C),then screw 4 X metal
nuts (E) with spanner (G) until tight.
STEP THREE
STEP FOUR
1. Attach panels 5 (x2) to panels 4 (x2).
STEP FIVE
Page 3 of 5

1. Attach panels 4 (x2) to panels 2 (X4) with 8 x screws (I)
using a screwdriver until tight.
1.Carefully lift the unit upright. Two person requited
2.Attach panels 5 (x2) to panel 1 with 6 x screws (H)
using a screwdriver until tight as shown in diagrm.
STEP SIX
STEP SEVEN
1. Push the button of latch (J) underneath into the hole as
illustration.
STEP EIGHT
Page 4 of 5

1. Ensure to hold the table by the apron and not the
table top. Take care that the top does not flip open
whilst lifting.
1. Unlock the latch (J) under the table top as shown.
STEP NINE
STEP TEN
1. To open the table push/pull the table top across and flip over the top
2. Do not allow the tops to slam together when open and closing as this way cause damage to the panels.
3. Push the button of latch (J) underneath into the hole as illustration.
STEP ELEVEN
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 5 of 5