Next 812846 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services
Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to
be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
MILANO GLOSS CORNER SHELF
by-step instructions.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Made from hollow board with a PVC finish.
• Made in China
• We recommend that the packaging is used to protect the surfaces during assembly.
PRODUCT INFORMATION
CARE INSTRUCTIONS
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft cloths
(including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try your cloth in
an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for cleaning is included
within the hardware pack
•Gloss finishes are prone to light surface scratch and it is therefore very imporant that
you care for this item correctly.
• Do not rub or scrub the surface when cleaning.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
Page 1 of 4

Please note: Remove the protective film after assembly of this product unless it is stated in
the steps to do so - this will prevent accidental scratches during assembly
STEP ONE
PARTS
FITTINGS
1. Please remove the protective film from the surface of
panel 2
2. Insert 10 x cambolts (C) into panel 2 and tighten with a
screwdriver.
1. Glue and insert 5 x wooden dowels (A) into
panel 2.
2. Attach panels 5 (x2) to panel 2.
3. Insert 10 x camlocks (D) into panels 3 (x5).
Ensure the arrow indicators are pointing towards
the panel edges before tightening with a
screwdriver.
STEP TWO
Page 2 of 4

1. Please remove the protective film from the
surface of panel 1
2. Carefully turn over the assembled unit as shown.
3. Attach panel 1 to panels 3 (x5) & panel 2 with
15 x screws (G) using an Allen key (H) to tighten.
1.Use 15 x stickers (E) to cover the screw holes on
panel 1.
STEP THREE
STEP FOUR
1.Using screw and washer secure the
nylon straps (F) to the back panel.
2.Secure the other end of the strap to the wall
with an appropriate screw and wall plug
for your wall type (not provided).
To hide the strap behind the unit ,drill the hole
lower than the top of unit.
Warning:
Always ensure intended wall area to be
drilled is free from hidden electrical wires,
water and gas pipes.
NB:Wall fixings are not included-Please source
suitable fixing for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP FIVE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 3 of 4

Page 4 of 4