Next MODE 857326 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
857326 MODE CORNER TV UNIT
857326 MODE CORNER TV UNIT 857326 MODE CORNER TV UNIT
857326 MODE CORNER TV UNIT
• Do not rub or scrub the surface when cleaning.
• Please do not apply adhesive substrates for example , sticky tape to the product.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Do not put hot dishes directly on the surfaces of the item.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not use furniture polish.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
• Made from honeycomb board, hollow board , partical board & MDF with a wood effect finish.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Made in China.
• Keep fittings out of children's reach and keep children well away from the construction area.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• Please do not apply adhesive substrates for example , sticky tape to the product.
Page 1 of 5

PARTS
FITTINGS
1. Insert 16 × cambolts (D) into panels 1, 2, 3 & 5 and
tighten with a screwdriver.
STEP ONE
Page 2 of 5

1. Glue and insert 2 x wooden dowels (A) into panel 2.
2. Attach panel 11 to panel 2.
3. Insert 3 x camlocks (C) into panel 2 and tighten with
a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1. Glue and insert the 2 x wooden dowels (A) into panel
2.
2. Attach panels 5 & 3 to panel 2.
3. Insert 4 x camlocks (D) into panel 2 and tighten with
a screwdriver.
4. Glue and insert the 2 x wooden dowels (A) into panel
2.
5. Attach panel 13 to panel 2.
6. Insert 1 x camlock (D) into panel 13 and tighten with
a screwdriver.
STEP TWO
STEP THREE
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
7. Attache panels 4, 7 & 6 to panel 2 with 6 × screws (E)
and tighten with an Allen key (F).
1. Carefully lift the unit upright, the unit should be lifted
by two people
2. Slide panel 12 into the grooves of the assembled
unit.
STEP FOUR
Page 3 of 5

1. Glue(B) and insert 8 x wooden dowels (A) into panels
3, 4, 5, 6 & 7.
2. Attach panel 1 to panels 3, 4, 5, 6 & 7 .
3. Insert 8 x camlocks (C ) into panels 3, 4, 5, 6 & 7 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1. Insert 8 x fittings (G) into the required position
2. Insert panels 9 & 10 onto the fittings (G) .
STEP SIX
STEP FIVE
1. Attach 2 × hinges (I) to panel 8 with 4 × screws (H)
by using a screwdriver until tight.
2. Attach 1 x handles (J) to the panel 8 with 2 x bolts
provided
3. Attach panels 8 to panel 3 with 4 × screws (H)
through 2 x hinges (I) by a screwdriver.
To align doors use the adjustment diagram below.
LATERAL
VERTICAL
FRONT-TO-BACK
4. Use 3 x stickers (K) to cover the camlock holes.
STEP SEVEN
4. Use 3 x stickers (K) to cover the camlock holes.
Page 4 of 5

1. Insert 6 x plastic fasteners (L) into the back panel
grooves and tighten with screws provided.
STEP EIGHT
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 5 of 5