Next 882462 NAVY RED BOYS TOY BO User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We recommend that the packaging is used to protect the surfaces during assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• A minimum of 2 persons is required to assemble this product.
• Not suitable for use in bathrooms.
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• For general cleaning, periodically dust with a soft cloth.
• Made from MDF with a painted finish.
• Made in China.
PRODUCT INFORMATION
CARE INSTRUCTIONS
882462 NAVY RED BOYS TOY BO
Page 1 of 8

1. Insert 4 x wooden dowels (A) into back panel
4.
2. Attach 2 x side panel 2 to back panel 4 with 6
x screws (B) and tighten with a screwdriver.
3. Insert bottom panel 5 into the grooves of 2 x
side panel 2 and back panel 4 .
STEP ONE
PARTS
FITTINGS
STEP TWO
Page 2 of 8

1. Insert 4 x wooden dowels (A) into 2 x side
panel 2 .
2. Attach front panel 3 to the assembled unit
with 6 x screws (B) and tighten.
1. Attach 2 x hinges (E) to top panel 1 with 4 x
screws (C) and tighten.
1. Attach top panel 1 to the assembled unit with
4 x screws (C) and tighten.
STEP THREE
STEP FOUR
STEP FIVE
Page 3 of 8

1. Attach 2 x stays (D) to the top panel 1 and
back panel 4 with 8 x screws (C) and tighten.
2. Attach 2 x rubber stopper (F) to the top panel
1 .
1. Insert 4 x wooden dowels (A) into back panel
9.
2. Attach 2 x side panel 7 to back panel 9 with 6
x screws (B) and tighten with a screwdriver.
3. Insert bottom panel 10 into the grooves of
side panel 7 (x2) and back panel 9.
STEP SEVEN
STEP EIGHT
STEP SIX
Page 4 of 8

1. Insert 4 x wooden dowels (A) into 2 x side
panel 7.
2. Attach front panel 8 to the assembled unit
with 6 x screws (B) and tighten.
1. Attach 2 x hinges (E) to top panel 6 with 4 x
screws (C) and tighten.
1. Attach top panel 6 to the assembled unit with
4 x screws (C) and tighten.
STEP ELEVEN
STEP NINE
STEP TEN
Page 5 of 8

1. Attach 2 x stays (D) to the top panel 6 and
back panel 9 with 8 x screws (C) and tighten.
2. Attach 2 x rubber stopper (F) to the top panel
6 .
1. Attach 8 x velvet pad ( G ) to the bottom of
side panel 2 (both L&R) and side panel 7 (both
L&R) .
STEP THIRTEEN
STEP TWELVE
Page 6 of 8

PACKAGING LAYOUT
Page 7 of 8

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 8 of 8