Next MILANO 895465 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
895465 MILANO BLACK GLOSS
TALL SHELF
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
CARE INSTRUCTIONS
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Made from PB,MDF,hollow board & Honeycomb board with a pvc foil finish.
• Made in China.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
PRODUCT INFORMATION
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft cloths
(including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try your cloth in
an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for cleaning is included
within the hardware pack
• Carefully check that you have all parts before beginning assembly.
• Do not use furniture polish.
• Do not put hot dishes directly on the surfaces of the item.
• Keep fittings out of children's reach and keep children well away from the construction area.
•Gloss finishes are prone to light surface scratch and it is therefore very important that
you care for this item correctly.
• Do not rub or scrub the surface when cleaning.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
Page 1 of 10

FITTINGS
PARTS
7.5*35m/m 15*10m/m
A2638+H=2
Please note: Remove the protective film after assembly of this product unless it is stated in
the steps to do so - this will prevent accidental scratches during assembly
1.Attach panels 18 (x2) & 19 (x2) to panels 20 (x2) with 8
× screws (F) by using a screwdriver until tight.
STEP ONE
Page 2 of 10

1.Slide panels 21(x2) into the grooves of the drawer
frame.
1.Insert 4 × cambolts (A) into panels 16 & 17 and using a
screwdriver until tight.
2. Glue (E) and insert 4 x wooden dowels (D) into panels
18 (x2) & 19 (x2) and attach panels 16 & 17 to panels 18
(x2) & 19 (x2).
3. Insert 4 x camlocks (B) into panels 18 (x2) & 19 (x2)
and tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP THREE
STEP TWO
Unfinishedside
the camlock before turning
1.Insert 5 × cambolts (A) into panels 4, 5 & 6 and using a
screwdriver until tight.
2. Attach push & out (H) on panel 5 with 2 x screws(H)
provided on pre-drill hole position as shown in diagram.
3. once push & out (H) are correctly adjusted then
fasten with 2 x screws(H) on the remaining holes in the
push & out (H) .
STEP FOUR
Page 3 of 10

1.Attach panel 7 as diagram to panel 4 with 2 × screws
(I) and tighten with an Allen key (J).
1. Glue (E) and insert 1 x wooden dowel (C) into panel 4
and attach panel 8 to panel 4.
2. Insert 2 x camlocks (B) into panel 8 and tighten with a
screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP FIVE
STEP SIX
1.Attach panel 5 as diagram to panel 8 with 2 × screws
(I) and tighten with an Allen key (J).
STEP SEVEN
Page 4 of 10

1. Glue (E) and insert 1 x wooden dowel (C) into panel 5
and attach panel 7 as diagram to panel 5.
2. Insert 2 x camlocks (B) into panel 7 and tighten with a
screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
1. Attach panel 6 as diagram to panel 7 with 2 × screws
(I) and tighten with an Allen key (J).
STEP NINE
STEP EIGHT
1. Glue (E) and insert 1 x wooden dowel (C) into panel 6
and attach panel 15 to panel 6.
2. Insert 1 x camlock (B) into panel 15 and tighten with a
screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP TEN
Page 5 of 10

1. Slide panel 10 into the assembled unit as shown in
diagram.
1.Insert 18 × cambolts (A) into panels 1, 2 & 3 and using
a screwdriver until tight.
2. Attach push & out (H) on panel 3 with 2 x screws(H)
provided on pre-drill hole position as shown in diagram.
3. once push & out (H) are correctly adjusted then
fasten with 2 x screws(H) on the remaining holes in the
push & out (H) .
STEP ELEVEN
STEP TWELVE
push & out (H) .
1. Glue (E) and insert 3 x wooden dowels (C) into panels
4, 5 & 6 and attach panel 1 to panels 4, 5 & 6.
2. Insert 6 x camlocks (B) into panels 4, 5 & 6 and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP THIRTEEN
Page 6 of 10

1. Glue (E) and insert 2 x wooden dowels (C) into panel 8
and attach panel 14 to panel 8.
1. Slide panel 11 into the assembled unit as shown in
diagram.
STEP FIFTEEN
STEP FOURTEEN
1. Glue (E) and insert 5 x wooden dowels (C) into panels
4, 5, 6 & 14 and attach panel 2 to panels 4, 5, 6 & 14.
2. Insert 6 x camlocks (B) into panels 4, 5 & 6 and tighten
with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP SIXTEEN
Page 7 of 10

1. Carefully upright this assembly unit by two person
2. Slide panel 10 into the assembled unit as shown in
diagram.
1. Glue (E) and insert 3 x wooden dowels (C) into panels
1, 7 & 2 and attach panel 3 to panels 1, 7 & 2.
2. Insert 6 x camlocks (B) into panels 1, 7 & 2. and
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the panel
edge and ensure the assembly bolt locates properly into
the camlock before turning
STEP SEVENTEEN
STEP EIGHTTEEN
1. Insert 16 x fittings (M) into the required position .
2. Insert panels 12 (x2) & 13 (x2) onto the fittings (M) .
3. Use 4 x stickers (O) to cover the camholes on matt
face.
4. Use 4 x stickers (P) to cover the camholes on gloss
face .
STEP NINETEEN
Finishedside
Finishedside
Glossside
Glossside
Page 8 of 10

1. Attach 4 x hinges (K) to panels 9 (x2) with 8 x screws
(L) using a screwdriver clockwise until tight.
2. Attach 2xfitting (G) to panels 9 (x2) and using a
screwdriver clockwise until tight.
2. Attach panels 9 (x2) to panel 1 with 8 x screws (L)
through hinges (K) using a screwdriver to tighten.
To align doors use the adjustment diagram
below.
LATERAL
STEP TWENTY-ONE
STEP TWENTY
VERTICAL
FRONT- TO-BACK
1. Insert the assembled drawers to the unit as diagram.
STEP TWENTY-TWO
Page 9 of 10

1. Insert 12 x plastic fasteners (N) into the back panel
grooves and tighten with screws provided.
2. Using screw and washer secure the 2 x nylon straps
(Q) to the back of top panel.
3. Secure the other end of the strap to the wall with an
appropriate screw and wall plug for your wall type (not
provided).
To hide the strap behind the unit ,drill the hole lower
than the top of unit.
Warning:
Always ensure intended wall area to be drilled is free
from hidden electrical wires,water and gas pipes.
NB:Wall fixings are not included-Please source suitable
fixing for your wall type. If in doubt please consult a
qualified trades person.
STEP TWENTY-THREE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 10 of 10