Next BARLOW 802062 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
damage.
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
• Ensure the mats and coasters used do not have an abrasive surface underneath.
• Made from particleboard,MDF with a wood effect finish.
• Made in Indonesia.
CARE INSTRUCTIONS
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons are required to assemble this product.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty.
Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
PRODUCT INFORMATION
802062 BARLOW COFFEE TRUNK
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
1 of 9

Hx2 Ix1 LLx2 LRx2
PARTS
1x1 2x1 3Lx1 3Rx1
4x1 5x1 6x1 7x1 8x1
9x2 10Lx2 10Rx2 11x2 12x2 13x2
FITTINGS
15x12 mm. 7.5X32 mm. 8x32 mm. F6x13 mm. 7.5X15 mm. P4x15 mm. 25x30 mm
Ax30 Bx30 Cx33 Dx8 Ex4 Fx2 Gx2
F10x70 mm. F6x30 mm. 350 mm. 350 mm
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
2 of 9

- Attach 8 x cambolts (B) into the holes on panel 1.
- Turn clockwise with cross-blade screwdriver to tighten.
Recommend to use cross-blade screwdriver.
- Insert 1x wooden dowel (C) into the hole on panel 8.
- Attach panel 8 to panel 2 using 1 x screw (I) and tighten by
turning clockwise with cross-blade screwdriver.
- Insert 2x camlocks (A) into the holes of panel 3L and ensure
that arrow indicator is pointing towards the panel edge
- Attach 4x cambolts (B) and 2x wooden dowels (C) into the
holes
on panel 3L.
Recommend to use cross-blade screwdriver.
STEP TWO
STEP THREE
STEP ONE
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
1
2
8
3L
3 of 9

- Insert 2x camlocks (A) into the holes on panel 3R and ensure
that arrow indicator is pointing towards the panel edge
- Attach 4x cambolts (B) and 2x wooden dowels (C) into the
holes
on panel 3R.
- Insert 2x camlocks (A) into the holes on panel 4 and
ensure that arrow indicator is pointing towards the panel edge.
- Insert 2x wooden dowels (C) into the holes on panel 4.
- Insert 8x camlocks (A) into the holes on panel 5 and
ensure that arrow indicator is pointing towards the panel edge.
- Insert 6x wooden dowels (C) into the holes on panel 5.
- Insert 2x camlocks (A) into the holes of panel 6 and
ensure that arrow indicator is pointing towards the panel edge.
- Insert 2x wooden dowels (C) into the holes on panel 6.
- Insert 2x camlocks (A) into the holes on panel 7 and
ensure that arrow indicator is pointing towards the panel edge.
- Insert 2x wooden dowels (C) into the holes on panel 7.
- Turn over panel 7 and attach 2x cambolts (B) into the holes on
panel 7.
Recommend to use cross-blade screwdriver.
STEP FOUR
STEP FIVE
STEP SIX
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
3R
6
5
4
7
7
4 of 9

- Attach panel 5 to panel 7 and tightening 2x camlocks (A)
clockwise with a flat-blade screwdriver until tight.
- Attach panel 5,7 and 6 to panel 3R and tighten using the 4x
camlocks (A).
Turn camlocks clockwise with a flat-blade screwdriver until tight.
- Attach panel 3L to the assembled using 4 x camlocks (A).
Turn camlocks clockwise with a flat-blade screwdriver until
tight.
STEP NINE
STEP SEVEN
STEP EIGHT
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
7
5
5 of 9

- Attach panel 4 to the assembled unit using 2 screws (H)
and tighten by turning clockwise with a cross-blade screwdriver.
- Slide panel 2 into the unit.
- Insert 4x mini cambolts (E) into the holes of assembled unit
and
tightening with a cross-blade screwdriver until tight.
- Slide panel 2 to sit on the mini cambolts (E) and secure
by tightening the housing screws clockwise with a cross-blade
screwdriver as shown..
- Attach panel 1 to the assembled unit. Tighten camlocks
(A) by turning clockwise with a flat-blade screwdriver.
STEP TEN
STEP ELEVEN
STEP TWELVE
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
6
3L 7
4
53R
6
4
3R
3L
2
3R
3L
2
6
54
1
3R
1
6 of 9

- Insert 3x cambolts (B) into the holes on panel 9.
- Attach 1x handle (G) to panel 9 using 1 x screw (F)
Tighten screw (F) using a flat-blade screwdriver .
- Attach 1x camlock (A) into the hole on panel 10L and 10R and
ensure that arrow indicator is pointing towards the panel edge.
- Insert 2 x wood dowels (C) into the holes on panel 10L and
10R.
- Turn over and insert 2 x cambolts (B) into the holes on panel
10L
and 10R.
- Repeat step 13 for the second set of components.
- Attach 2x camlocks (A) into the holes on panel 11 and ensure
that arrow indicator is pointing towards the panel edge.
- Insert 4x wood dowels (C) into the holes on panel 11.
- Attach 2x camlocks (A) into the holes on panel 12 and ensure
that arrow indicator is pointing towards the panel edge
- Insert 2x wood dowels (C) into the holes on panel 12.
- Turn over and insert 1x cambolt (B) into panel 12.
- Repeat step 14 for the second set of components.
- Attach panel 10R and 10L to panel 12 and tighten
camlocks (A) by turning clockwise with a flat-blade screwdriver.
- Repeat step 15 for the second set of components.
STEP THIRTEEN
STEP FOURTEEN
STEP FIVETEEN
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
10L
10L
10R
10R
11
12
12
10R
10L
12
10L
7 of 9

- Attach panel 11 to the assembled unit and tighten
camlocks (A) by turning clockwise with a flat-blade screwdriver.
- Repeat step 16 for the second set of components.
- Insert panel 13 to the recessed grooves of panel 10L,10R
and 12.
- Repeat this step for the second drawer.
- Attach panel 9 to the assembled unit and tighten using 3x
camlocks (A) by turning clockwise with a flat-blade screwdriver.
- Repeat this step for the second drawer.
STEP SIXTEEN
STEP SEVENTEEN
STEP EIGHTEEN
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
12
10L
11
12
11
10R
10L
12
11 10R
13
9
13
10L
10L
12
11 10R
9
8 of 9

- Attach 1x male runner (LR) to the assembled unit using
2x screws (D)
- Attach 1x male runner (LL) to the assembled unit using
2x screws (D)
- Repeat this step for the second drawer
- Insert the drawers into the assembled unit.
- The coffee trunk is ready for use.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP NINETEEN
STEP TWENTY
7
5
6
6
3R
3R
3L
5
6
6
3L
3R
7
10R
10R
9
10L
6
210L
3L
1
9
10R
9
10L
10R
3R
9 of 9