Next MILANO 659698 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Keep fittings out of children's reach and keep children well away from the construction area.
ASSEMBLY INSTRUCTIONS
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to
be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
659698 MILANO WHITE GLOSS CORNER TV UNIT
• Do not put hot dishes directly on the surfaces of the item.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• A minimum of two persons is required to assemble this product.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft
cloths (including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try your
cloth in an inconspicuous area of the furniture first to assess its suitability. A sample of a suitable cloth for cleaning is
included within the hardware pack
• Made from PB,MDF,hollow board & Honeycomb board with a pvc foil finish.
• Made in China.
CARE INSTRUCTIONS
PRODUCT INFORMATION
•Gloss finishes are prone to light surface scratch and it is therefore very important
that you care for this item correctly.
• Do not rub or scrub the surface when cleaning.
• Do not use furniture polish.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
Page 1 of 5

Please note: Remove the protective film after assembly of this product unless it is stated in
PARTS
STEP ONE
FITTINGS
the steps to do so - this will prevent accidental scratches during assembly
1. Insert 23 x cambolts (D) into panels 1, 2 & 11 (x2)
and tighten with a screwdriver.
1. Attach panels 3, 6, 4, 7 & 5 to panel 2 with 10 x
screws (E) and tighten with an Allen key (F) .
STEP TWO
Page 2 of 5

1. Glue (B) and insert 4 x wooden dowels (A) into
panels 11 (x2).
2. Attach panels 11 (x2) to panels 12 (x2).
3. Insert 4 x camlocks (C) into panels 12 (x2) and
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning.
1. Glue (B) and insert 8 x wooden dowels (A) into
panel 2.
2. Attach assembly frame to panel 2 .
3. Insert 8 x camlocks (C) into panels 12 (x2) & 11
x2) and tighten with a screwdriver.
4. Glue (B) and insert 2 x wooden dowels (A) into
panel 2.
5. Attach panel 13 to panel 2 .
6. Insert 1 x camlock (C) into panel 13 and tighten
with a screwdriver.
STEP THREE
STEP FOUR
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning.
4. Please remove the protective film from the outside
surface of panels 3, 4 & 5 (x2).
1. Carefully lift the unit as shown in diagram by two
person .
2. Slide panel 8 into the grooves of the assembled
unit.
STEP FIVE
Page 3 of 5

1. Glue (B) and insert 6 x wooden dowels (A) into the
panels 3, 4, 5, 6 & 7 .
2.Attach panel 1 to panels 3, 4, 5, 6 & 7.
3. Insert 10 x camlocks (C) into panels 3, 4, 5, 6 & 7
and tighten with a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and ensure the assembly bolt locates
properly into the camlock before turning.
1.Insert 8 x fittings (K) into required positions of
panels 3, 4 & 5
2.Insert adjustable shelves 9 (x2) onto the fittings
(G).
STEP SEVEN
STEP SIX
1.Attach 2 x fittings (I) into the required position on
panel 10 with 4 x screw(H) provided.
2. Insert panel 10 into the groove of the top panel 1
as shown. Lift the door panel at an angle and slot
into the groove in panel 1, slide the underneath
towards panel 2 and locate the rollers into the runner
in panel 2.
STEP EIGHT
Page 4 of 5

1. Insert 6 x plastic fasteners (J) into the back panel
groove and tighten with screws provided.
STEP NINE
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 5 of 5