Next OXFORD TRIPLE ROBE User manual

Carefully check that you have all the parts before beginning assembly.
Helpline
Tools Needed
•
We recommend that the packaging is used to protect the surfaces during assembly.
We suggest you retain these instructions for future reference.
• Keep fittings out of children’s reach and keep children well away from construction area.
•
All you need to assemble this piece of
furniture is a flat and crosshead screwdriver
as well as a hammer
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
(Not supplied)
•
•
Assembly Instructions
Please keep these instructions for future reference
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the items
• A minimum of 2 persons is required to assemble this product.
are found to be faulty. Should you need to return the unassembled product, please repack in its original
packaging.
We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step•
instructions.
Made with solid oak and oak veneer with a clear lacquer finish.•
Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between•
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
Oak wood and veneers often have random pale markings in the grain, these are medullary rays which are a•
natural unique feature of this wood
Made in China.
1 of 25
448648 OXFORD TRIPLE ROBE
Important
Product Information

L x 18
Ȍx 1 @ x 1
A x 40
8x30
B x 19
6x44
C x 68 D x 12
6x41
X x 6
15x12
V x 66
G x 3
35
H x 3 J x 3
3.5x14
K x 3
6x9
20xM8
Z x 1
N x 6
3x12
P x 12
M4x18
4x25
$ x 12 & x 1
L=931
Q x 8 R x 8
M x 66
E x 7
4x30
F x 1
ȍx 1
3x16
S x 4 T x 6
U x 6 W x 12
L=400 L=400 L=400 L=400
35
Ȉx 6
M47x50
ĭx 2
L=490
Y x 2
# x 75
15x12
M6x40
•
Avoid exposing the furniture to excessive heat or direct sunlight as this can cause cracking•
of the wood and deterioration of the colour.
Periodically dust lightly with a soft cloth.•
Any spills should be removed immediately with a damp cloth.•
Do not use silicone based furniture polish.•
Ensure that the product is protected with mats & coasters when items are placed on to its surface.•
Never put hot dishes directly onto wooden or glass surfaces as this may mark the furniture.
Wood will mellow and change colour over time, we recommend that ornaments and items placed on•
the surface are moved regularly for the first few months to prevent uneven mellowing.
Take care when moving the furniture and never drag the pieces across the floor, as this will cause•
damage to the joints.
Periodically check fittings are secure and re-tighten as necessary.•
Please do not apply Adhesive substrates for example, sticky tape to the product.
2 of 25
O x 2
Care Instructions
Fittings

PACK PANELS LIST
1 - 4 1x 1
PACK PANELS LIST PACK PANELS LIST PACK PANELS LIST
& x 1
4 - 43 - 42 - 4
6
7
10
11
14
16
15
22
23
24
25
27
36
35
34
33
32
31
29
28
x 1
x 1
x 1
x 1
x 3
x 1
x 1
x 1
x 1
x 1
x 3
x 1
x 1
x 1
x 1
x 1
x 1
x 3
x 1
x 1
ȍx 1
2x 1
3
8
9
17
18
x 1
x 1
x 1
x 2
x 1
4x 1
5
12
13
x 1
x 1
x 1
19 x 2
20
21
26
30
x 1
x 1
x 1
x 1
3 of 25
1
8
2
3
4
5
6
7
9
10
11 12
13
15
16
17
17
18
19
20
21
22
23
24
25
25
25
26
27
28
29
30
31
32
33
34 x3
36
35
19
14a 14b
Parts

4 of 25
5
• Insert dowels (A) into panel (6) with a hammer.
Attach hanging rail supports (S) to panel (5) and tighten with screws (M).
•
•
Insert cam bolts (C) into panel (5) tighten with a screwdriver.
•
•
Install runners (H) to panel (5) and tighten with screws (L).
Insert dowels (A) into panel (5) with a hammer.
(Assemble on a flat and even surface)
Install runners (G) to panel (6) and tighten with screws (L).•
Ax4
L
Hx3 Lx9
Ax4
Gx3 Lx9
L
Cx3
Attach hinge plates (O) to panel (5) and tighten with screws (M).•
5
Mx1
Sx1
Mx8
Ox2
G
G
G
6
Mx1
Sx1
Step One
Step Two

7
65
Insert cam bolts (C) into panel (7), tighten with a screwdriver.•
Insert dowels (A) into panel (7) with a hammer.•
Attach panels (5) and (6) to panel (7), insert cam locks (#) to panels (6) and (7) and•
tighten with a screwdriver.
Cx3
Ax2
#x6
5 of 25
7
Step Three
Step Four

5
6
4
6 of 25
Insert dowels (A) into panels (4), (15) and (16) with a hammer.•
Attach panels (5) and (6) to panel (4), tighten with screws (E) and allen key (F).•
Ax8
Ex6
Fx1
4
16
15
Step Five
Step Six

2
3
5
4
15
16
Insert cam bolts (C) into panels (2) and (3), tighten with a screwdriver.•
Attach panels (2) and (3) to panels (4), (15) and (16), insert cam locks (#) to•
panels (4) and (15), tighten with a screwdriver.
Insert dowels (A) into panels (2) and (3) with a hammer.•
Attach hanging rail supports (S) into panels (2) and (3), tighten with screws (M).•
Cx10
Ax4
#x8
7 of 25
2
3
Mx2
Sx2
Step Seven
Step Eight

8 of 25
Insert dowels (A) into panels (14a) and (14b) with a hammer.•
Insert cam bolts (C) into panels (14a) tighten with a screwdriver.•
Insert cam bolts (C) into panels (12) and (13), tighten with a screwdriver.•
Insert dowels (A) into panels (12) and (13) with a hammer.•
Ax6
Cx2
Ax4
Cx13
14a
14b x2
12
13
Step Nine
Step Ten

Attach panels (12) and (13) to panels (14a) and (14b), insert cam locks (#) into•
panels (14a) and (14b), tighten with a screwdriver.
Insert dowels (A) into panels (10) and (11) with a hammer.•
Insert cam bolts (C) into panels (10) and (11), tighten with a screwdriver.•
Cx9
Ax4
#x6
9 of 25
11
12
13
14a
14b
14b
10
Step Eleven
Step Twelve

10 of 25
Insert cam bolts (C) into panels (8) and (9), tighten with a screwdriver.•
Attach hinge plates (R) to panels (8) and (9) and tighten with screws (M).•
Attach panels (10) and (11) to panels (12) and (13), insert cam locks (#) to panels•
(12) and (13), tighten with a screwdriver.
Cx16
#x4
10
11
13
12
9
Mx16
Rx8
8
17mm
17mm
Step Thirteen
Step Fourteen