Next SHOREDITCH 832384 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• Do not put hot dishes directly on the surfaces of the item.
• Never drag pieces of furniture across the oor as this will cause damage to the joints.
• All assembly xings should always be tightened properly and periodically check all xings and tighten if necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching
or damage.
• Do not rub or scrub the surface when cleaning.
• Made in China.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
PRODUCT INFORMATION
• Made from steel with an antique bronze plated nish and poplar sprung wooden slats.
• Carefully check that you have all parts before beginning assembly.
• Keep ttings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Do not use abrasive cleaning products or those containing silicone.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging
• We suggest you spend a short time reading through this leaet and then follow the simple step by step instructions.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
IMPORTANT
• A minimum of two persons is required to assemble this product.
SHOREDITCH METAL BED 832384
Page 1 of 5

FITTINGS
PARTS
A. Bolts x12
M6X20mm
G. Spanner x 1
11mm
B. Bolts x4
M6X55mm
D. Plastic Washer x8
M6
C. Nut x2
M6
F. Allen key x1
4mm
E. Metal Washer x 18
M6
(1) Headboard x 1
(2) Footboard x 1
(3) Side Rail x 2
(5) Centre Rail x 1
(4) Cross Bar x 2
(6) Sprung Slats x 26
(7) Plastic cap (one
end open) x 26
(9) Fabric straps 2
(10) Support
Feet x 2
(8) Plastic cap (two
end open) x 13
Page 2 of 5

1. Attach cross bars 4 (x2) to the brackets on side
rails 3 (x2) using 4 x bolts (A) and 4 x metal washers
(E). Tighten with Allen key (F).
NOTE: Ensure the threaded insert holes in cross bars
4 (x2) are facing downwards.
STEP ONE
1. Attach side rails 3 (x2) to headboard 1 and
footboard 2 using 8 x bolts (A), 8 x plastic washers (D)
and 8 x metal washers (E). Tighten using Allen key (F)
STEP TWO
Page 3 of 5

1. Attach centre rail 5 between the brackets on cross
bars 4 (x2) using 2 x bolts (B), 4 x metal washers (E)
and 2 x nuts (C). Tighten with Allen key (F) and
spanner (G).
NOTE: Please ensure that the slat cap holes on the
centre rail 5 face upwards.
1. Attach 2 x support feet 10 to centre rail 5 using 2 x
bolts (B) and 2 x metal washers (E). Tighten with Allen
key (F).
IMPORTANT
Once the feet have been assembled and attached,
they should be adjusted to ensure they do not touch
the floor, (5mm above the floor) to allow for
movement once the mattress is placed on the bed
frame.
It is important to note that when moving the bed that
it is not dragged into its new position to prevent the
possibility of these feet being twisted or angled to one
side, which could lead to the collapse of the centre of
the bed.
To move the bed, remove the mattress and lift the bed
into its new position to avoid damage. Ensure the feet
are at 90° to the floor before replacing the mattress.
STEP THREE
STEP FOUR
STEP FIVE
Page 4 of 5

1. Insert a sprung wooden slat 6 through the first hole
in strap 9. Repeat using another sprung wooden slat 6
and the other strap 9.
2. Attach single sided slat cap 7 onto one end of the
sprung wooden slat 6. Attach another single sided
slat cap 7 onto the other end of the second sprung
wooden slat 6.
3. Attach both sprung wooden slats to the assembled
bed base by inserting each single sided slat cap 7 into
side rails 3 (x2) and using double sided slat cap 8 in
the centre. Once each slat has been inserted into the
slat caps, ensure the double sided slat cap is firmly
pushed into the holes in centre rail 5.
4. Repeat process for all remaining slats and caps
until all components have been used and firmly
pushed in place.
STEP SIX
STEP SEVEN
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 5 of 5