Nikon NIKKOR Z DX 16-50mm f/3.5-6.3 VR User manual

NIKKOR Z DX 16-50mm f/3.5-6.3 VR
En
User’s Manual
SB1C01(11)
7MMA6011-01

2
Before using this product, please read these instructions carefully. You
will also need to consult the camera manual.
• This lens is intended exclusively for use with mirrorless cameras featuring
a Nikon Z mount.
• Update to the latest version of the camera firmware before using this lens
with the Z 7 or Z 6, as otherwise the camera may fail to correctly recognize
the lens and features such as vibration reduction may be unavailable. The
latest firmware is available from the Nikon Download Center.
For Your SafetyFor Your Safety
To prevent damage to property or injury to yourself or to others, read
“For Your Safety”in its entirety before using this product.
Keep these safety instructions where all those who use this product will read
them.
AWARNING: Failure to observe the precautions marked with this
icon could result in death or severe injury.
ACAUTION: Failure to observe the precautions marked with this
icon could result in injury or property damage.
AAWARNINGWARNING
•• Do not disassemble or modify this product.Do not disassemble or modify this product.
Do not touch internal parts that become exposed as the resultDo not touch internal parts that become exposed as the result
of a fall or other accident.of a fall or other accident.
Failure to observe these precautions could result in electric shock or other
injury.
•• Should you notice any abnormalities such as the product producingShould you notice any abnormalities such as the product producing
smoke, heat, or unusual odors, immediately disconnect the camerasmoke, heat, or unusual odors, immediately disconnect the camera
power source.power source.
Continued operation could result in fire, burns or other injury.

3
AAWARNINGWARNING
•• Keep dry.Keep dry.
Do not handle with wet hands.Do not handle with wet hands.
Failure to observe these precautions could result in fire or electric
shock.
•• Do not use this product in the presence of flammable dust orDo not use this product in the presence of flammable dust or
gas such as propane, gasoline or aerosols.gas such as propane, gasoline or aerosols.
Failure to observe this precaution could result in explosion or fire.
•• Do not directly view the sun or other bright light sourceDo not directly view the sun or other bright light source
through the lens.through the lens.
Failure to observe this precaution could result in visual impairment.
•• Keep this product out of reach of children.Keep this product out of reach of children.
Failure to observe this precaution could result in injury or product
malfunction. In addition, note that small parts constitute a choking
hazard. Should a child swallow any part of this product, seek immediate
medical attention.
•• Do not handle with bare hands in locations exposed toDo not handle with bare hands in locations exposed to
extremely high or low temperatures.extremely high or low temperatures.
Failure to observe this precaution could result in burns or frostbite.
AACAUTIONCAUTION
•• Do not leave the lens pointed at the sun or other strong lightDo not leave the lens pointed at the sun or other strong light
sources.sources.
Light focused by the lens could cause fire or damage to product’s
internal parts. When shooting backlit subjects, keep the sun well out
of the frame.
•• Do not leave the product where it will be exposed to extremelyDo not leave the product where it will be exposed to extremely
high temperatures, for an extended period such as in anhigh temperatures, for an extended period such as in an
enclosed automobile or in direct sunlight.enclosed automobile or in direct sunlight.
Failure to observe this precaution could result in fire or product
malfunction.

4
AACAUTIONCAUTION
•• Do not transport cameras or lenses with tripods or similarDo not transport cameras or lenses with tripods or similar
accessories attached.accessories attached.
Failure to observe this precaution could result in injury or product
malfunction.
Notices for Customers in the U.S.A.Notices for Customers in the U.S.A.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Federal Communications Commission (FCC) Radio FrequencyFederal Communications Commission (FCC) Radio Frequency
Interference StatementInterference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for
help.

5
CAUTIONSCAUTIONS
Modications
The FCC requires the user to be notified that any changes or modifi-
cations made to this device that are not expressly approved by Nikon
Corporation may void the user’s
authority to operate the equipment.
Nikon Inc., 1300 Walt Whitman Road,
Melville, New York 11747-3064, U.S.A.
Tel.: [phone]
Notice for Customers in CanadaNotice for Customers in Canada
CAN ICES-3 B / NMB-3 B

6
Using the LensUsing the Lens
Parts of the Lens: Names and FunctionsParts of the Lens: Names and Functions
See below for the names and functions of the parts of the lens.

7
qLens hood*
Lens hoods block stray light that
would otherwise cause flare or ghost-
ing.They also serve to protect the lens.
See C
(010)
wZoom ring Rotate to zoom in or out. Be sure to
extend the lens before use.
See B
(09)
eFocal length scale Determine the approximate focal
length when zooming the lens in or
out.
—
rFocal length mark
tControl ring
Autofocus mode selected:
In autofocus mode, rotate the ring to
adjust a setting such as [Focus (M/A)]
or [Aperture] assigned using the cam-
era. For more information, see the
description of [Custom control assign-
ment] /[Custom controls (shooting)]
in the camera manual.
—
Manual focus mode selected:
Rotate the ring to focus.
yLens mounting
mark
Use when mounting the lens on the
camera.
See A
(08)
uCPU contacts Used to transfer data to and from the
camera. —
iFront lens cap — —
oRear lens cap — —
* Available separately.

8
AAttachment and RemovalAttachment and Removal
Attaching the Lens
z
Turn the camera off, remove the body cap, and detach the rear
lens cap.
xPosition the lens on the camera body, keeping the mount-
ing mark on the lens aligned with the mounting mark on
the camera body, and then rotate the lens counterclockwise
until it clicks into place.
Removing the Lens
zTurn the camera off.
x
Press and hold the lens release button while turning the lens
clockwise.

9
BBefore UseBefore Use
The lens is retractable and must be extended before use. Rotate the
zoom ring as shown until the lens clicks into the extended position.
Pictures can only be taken when the focal length mark points to
positions between 16 and 50 on the focal length scale.
Pictures can be taken at
these focal lengths
To retract the lens, rotate the zoom ring in the opposite direction,
stopping when you reach the (●) position on the focal length scale.
If the camera is turned on with the lens retracted, a warning will be
displayed. Extend the lens before use.

10
CAttaching and Removing Optional Lens HoodsAttaching and Removing Optional Lens Hoods
Lens hoods (available separately)
screw directly into the threads in
front of the lens. Do not touch the
glass surface of the lens or use exces-
sive force.
To remove the hood, unscrew it from
the lens.