Nilfisk-Advance SC430 User manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
If the machine has been used until the red light illuminates on the battery level indicator on the machine, a full recharge of the batteries (10-12 hours) will be required. Failure to carry out this this
procedure may cause damage to the batteries. Charging the batteries after every use is recommended.
Use & maintenance
- SC430
17. Park the machine with the recovery
tank cover open.
16. Charge the batteries: Connect the
battery charger cable to the mains
electricity supply.
15. Clean the machine using a damp
cloth and where needed use a
neutral cleaning product.
14. Check and clean the squeegee
blades.
10. Wash with clean water the recovery
tank and the vacuum grid.
11. Remove the brush/pad and clean
them.
12. Take the squeegee off and remove
debris.
13. Check and clean the squeegee
blades.
5. Place the brush or the pad-holder
under the deck. Use the appropriate
brush to clean the floor.
9. At the end of the work. Empty the
recovery tank with the hose. Then
empty the solution tank with the
trasparent hose.
6. Adjust the eco solution flow control
valve.
8. Press the handle switch to engage
the brush and run the machine.
7. Switch on the brush and vac motors
to activate the machine.
2. Fill the tank with a clean water. The
clean water temperature must not
exceed 40 °C.
1b. Disconnect the battery charger
cable from the mains electricity
supply.
3. If the squeegee is not connected to
the machine: install and fasten it with
the handwheels, then connect to the
suction hose.
1a. Switch off charger by unplug
charger cable from red battery plug.
Reconnect the red battery plug to
the machine.
.
4. If the squeegee is in upper position,
lower it with the lever.
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual

Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Denmark
Tel.: [phone]
Fax: [phone]
mail.com@nilfisk.com
www.nilfisk.com
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
don’t work as they
should?
Troubleshooting
- SC430
ATTENTION! Do not use the machine before you have read and understood the Instructions for User Manual
1Check if the power cable is correctly
connected.
2Check if the battery is charged.
1Check if the brush is correctly
installed and not worn out.
2Check if there isn’t any brush motor
overload i.e. 3 battery LED lights
flashing simultaneously.
3Check if there are external materials
preventing the brush rotating.
1Check if the suction hose is
correctly installed and clean.
2Open the recovery tank and check
if the vacuum grid and gasket are
clean.
3Check if squeegee blades are
damaged or dirty.
4Close the recovery tank cover
properly and/or verify the gasket
wear.
1Check if you have the right water
settings.
2Check if the solution filter is clean.