Nitek MM-100 User manual

MM-100/1000 & MS-100/1000
10/100/1000 MEDIA CONVERTERS w/PoE Option
Introducon
This manual applies to the following media converters.
MM-100: Mul-Mode SC, 10/100 Mbps MS-100: Single-Mode SC, 10/100 Mbps
MM-1000: Mul-Mode SC, 10/100/1000 Mbps MS-1000: Single-Mode SC, 10/100/1000 Mbps
MM-100-POE: Mul-Mode SC, 10/100 Mbps, 30W PoE MS-100-POE: Single-Mode SC, 10/100 Mbps, 30W PoE
NITEK®
De Aar 99
8253 PN Dronten
The Netherlands
Tel: [phone]
E-mail: [email protected]
WWW.NITEK.NET
USA
5410 Newport Drive, # 24
Rolling Meadows, IL 60008
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
WWW.NITEK.NET
EUROPE
20171128
RJ45 Side Opcal Side
680700106
TX RX
PoE LED
(on POE Models)
Opcal
Link LED Device
Power LED
Power
Jack
RJ45
Jack
1000 Mbps
Link LED
10/100 Mbps
Link LED
LED OFF GREEN ORANGE BLINK
DEVICE
POWER
NO
POWER POWER N/A N/A
OPTICAL
LINK
NO
LINK LINKED N/A N/A
10/100
Mbps
LINK
NO
LINK
100
Mbps
LINK
10
Mbps
LINK
ACTIVE
LINK
1000
Mbps
LINK
NO
LINK
1000
Mbps
LINK
N/A ACTIVE
LINK
PoE PoE
OFF
PoE
ON N/A PoE FAULT
MODELS DC INPUT* AC INPUT
Non-PoE 6-16V 6-12V
PoE 48-56V N/A
LED FUNCTIONS POWER JACK OPTIONS
*POLARITY NOT IMPORTANT DUE TO INTERNAL BRIDGE
Installation and
Operation Manual

Installation and
Operation Manual
PoE Media Converter Installaon
Installing the MM-100/1000 & MS-100/1000 Series Media Converters
Refer to the diagrams above when installing. Use best industry pracces and follow all local building codes.
1. Connect the provided AC adapter to the power jack of the local unit and confirm that its device power LED turns on.
2. Connect a network cable from the network equipment to the RJ45 jack of the local unit and confirm that a link LED on its RJ45
jack turns on.
3. Connect appropriate optical cables (see note below) to the TX and RX ports of the local unit.
4. Connect the provided AC adapter or PoE power supply to the power jack of the remote unit and confirm that the device power
LED turns on.
5. Connect the other ends of the optical cables from step 4 to the TX and RX ports of the remote unit.
6. If the remote optical link LED doesn’t light, swap the cables between the TX and RX ports and confirm that it lights.
7. If the remote device will be powered by its own supply, connect that power supply as specified by its documentation and skip
to step 10.
8. If the remote media converter is a non-PoE model and PoE is required:
A. Connect the RJ45 jack of the remote media converter to the Data In jack of the PoE injector.
B. Connect the PoE & Data Out jack of the PoE injector to the remote device and skip to step 10.
9. If the remote media converter will provide PoE, connect the RJ45 jack of the remote unit to the remote device and conrm
that the PoE LED lights.
10. Confirm that the remote device is powered and that a link LED on the RJ45 jack of the remote unit turns on.
11. If the remote device is active, confirm that a link LED is blinking on the RJ45 jack of the remote unit.
12. Confirm that the optical link LED lights on the local unit and verify data connectivity via the network equipment.
NOTE:
MM models require multi-mode SC-terminated fiber cables, which are orange.
MS models require single-mode SC-terminated fiber cables, which are yellow.
Remote TX to Local RX
Remote Unit
w/PoE
Local Unit
Non-PoE Media Converter Installaon
Remote RX to Local TX
Remote TX to Local RX
Remote Unit
w/o PoE
Local Unit
Remote RX to Local TX
PoE Power
Supply
PoE
Injector
AC Adapter
AC Adapter
AC Adapter
Remote
Device
Remote
Device
Network
Equipment
Network
Equipment
MM-100/1000 & MS-100/1000
10/100/1000 MEDIA CONVERTERS w/PoE Option
Data
Data
Data
Data
PoE
Data
Data
PoE
Data
Data
Data

Troubleshoong Guide
Trouble Possible Cause Soluon
Remote device isn’t powered. Non-PoE remote device power is not
connected.
Make sure remote device’s power adapter is
plugged into device and AC outlet.
Remote device is connected to PoE from
remote unit and to AC adapter.
Cut a pair in the cable to the device used for
PoE. Typically, the brown pair can be cut.
PoE injector is not plugged in to AC power. Make sure PoE injector is plugged in to AC
Outlet.
PoE injector is not connected properly. Make sure remote device is connected to
PoE & Data Out port of injector (step 9 above).
Link LEDs light, but don’t blink. Remote device is not acve. Access the remote device through the network
equipment. For instances, view the video
output of an IP camera.
No lights on local or remote
unit.
Unit is not powered up. Make sure AC adapter or PoE supply is plugged
in to unit and AC outlet.
Opcal link LED doesn’t turn on. Opcal cables not connected properly. Swap RX and TX connecons at local or remote
unit.
Opcal bers are dirty. Clean ber faces using coon swab dipped in
isopropyl alcohol. Dust o ber face & barrel
of opcal module with canned duster.
Wrong opcal cables were used. Use orange cables with MM units and yellow
cables with MS units.
Installation and
Operation Manual
MM-100/1000 & MS-100/1000
10/100/1000 MEDIA CONVERTERS w/PoE Option
Call 800-528-4343 or 847-259-8900 for Nitek Tech Support (North America)
Call 0031 321 310 043 for Nitek Tech Support (Europe)