Nitek MC722MT?2 User manual

Model MC722MT-2
10/100 FIBER MEDIA CONVERTER
Installation and
Operation Manual
Introduction
TheMC722MT‐2auto‐negotiatingFastEthernetMediaConvertersetwhichisdesignedtotranslatesbetween10/100Base‐TX
copperand100Base‐FXfastEthernetfibercabling.TheMediaConverterenablesyoutoextendthedistanceofyour10/100BaseTX
Ethernetnetworkupto2kilometersoverMulti‐Modefiber.
TheConvertersareequippedwith[1]duplexSCfiberconnectortransmitdataovertwofibersupto2km.
SixLEDindicatorsarebuiltinforeasymonitoringandsystemdiagnosticsforpower,fiberandUTP,linkandactivity.
MC722MT‐2FiberMediaConverterInstallationDrawing
InstallingtheMC722MT‐2FiberMediaConverters
Refertotheabovediagramwheninstalling.Usebestindustrypracticesandfollowalllocalbuildingcodes.
1)Connectanetworkpatchcablefromthenetworkequipment’sEthernetstothereceiver.
2)ConnectaSingleModefibercablebetweenthetransmitterandthereceiverusingSCfiberconnectors.
3)Connectanetworkpatchcablefromthetransmitter’sEthernetjacktotheremoteIPdevice(IPcamerainthisexample).
4)Connectthesuppliedpowertransformerstothetransmitterandreceiver.
NITEK ®
De Schans 19-21 2a
8231 KA Lelystad
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
WWW.NITEK.NL
USA
5410 Newport Drive, # 24
Rolling Meadows, IL 60008
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
WWW.NITEK.NET
EUROPE
20810 681200105
FrontPanelRearPanel
LED Color Function
FX Green Litwhenfull‐duplexmodeisactive
TX Green Lit,100Mbs;off10Mbs
FX/LinkAct Green Litwhenfiberconnectionismade
Blinkswhendatatransferisactive
TX/LinkAct Green LitWhenRJ45isConnected
Blinkswhendatatransferisactive
FDX Green Litwhenfull‐duplexmodeisactive
PWR Green Litwhen5VoltDCpowerisapplied
LEDIndicators
TroubleShooting
(ContinuedonPage2)
2Multi‐ModeFibers
MC722MT‐2MC722MT‐2


TroubleShooting
1.IsthePowerLEDonthemediaconverterIlluminated?
Answer—No
●Checktoinsurepoweradapterisproperlyconnectedtothemediaconverterandthepoweroutlet.
●Isthecorrect5voldDCadapterthatwassuppliedwiththeunitbeingused?
●Contacttechsupportat(800)528‐4343
2.IstheFX/ACTIlluminated?
Answer—No
●ChecktheFiberconnectiontothemediaconverter.
●ChecktheSCfiberconnectoriscleanandproperlyconnectedtothefibercable
●Contacttechsupportat(800)528‐4343
3.IstheTX/ACTIlluminated?
Answer—No
●Checkthenetworkconnectorforpropertermination.
●Checktoinsurethenetworkistransmittingdata.
●Contacttechsupportat(800)528‐4343
Model MC722MT-2
10/100 FIBER MEDIA CONVERTER
Installation and
Operation Manual
NITEK ®
De Schans 19-21 2a
8231 KA Lelystad
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
WWW.NITEK.NL
USA
5410 Newport Drive, # 24
Rolling Meadows, IL 60008
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
WWW.NITEK.NET
EUROPE
20810 681200105