NiteRider MiNewt Pro 750 User manual

MiNewt Pro 750
PARTS LIST AND IDENTIFICATION
Please verify the contents of your MiNewt Pro 750 system
A. MiNewt Pro 750 Headlamp
B. Li-Ion Battery
C. O-Ring Mounting Straps
D. Low Prole Bike Helmet Mount
E. MiNewt Pro Slider Mount (SKU #4132)
F. 36” Extension Cable
G. A/C Adapter
MOUNTING THE LI-ION BATTERY
1. Thread the Velcro strap through the slots on the bottom of the
Li-Ion battery.
2. Attach the concave surface of the Li-Ion Battery to a safe,
convenient location on the handlebars, stem or frame, placing
the Velcro strap over the mating surface.
LOW BATTERY INDICATOR
With approximately 15% battery capacity remaining, the
indicator light on the headlamp will turn from green to red.
BATTERY CHARGING
1. Plug the AC Power Adapter into an electric outlet, then plug
the cable from the AC Power Adapter into the Li-Ion Battery.
2. The indicator light will be red until the Li-Ion battery is
fully charged; then it changes to blue.
3. Unplug the AC Adapter from the Li-Ion Battery by grasping
the connectors rather than the cable.
4. Leaving the Li-Ion Battery and AC Adapter connected
indenitely will not harm the batteries.
5. When storing for an extended period of time, charge battery
every four weeks to maximize battery life.
DISCOVER THE NIGHT
Thank you for choosing the MiNewt Pro 750 from NiteRider, the
innovator in technical lighting systems. The MiNewt Pro 750
combines a high-powered white LED headlamp and a Li-Ion
Battery.
To get the most from your NiteRider light, we urge you to
familiarize yourself with the following safety and operating
instructions.
RIDING AT NIGHT
While a MiNewt Pro 750 lighting system will improve your view,
control and enjoyment of night riding, please remember that
cycling at night is an inherently dangerous activity. In addition
to using your lighting system properly and riding with extreme
caution, NiteRider urges you to:
• Never ride alone.
• Always let someone know where you are going.
• Wear a helmet and reective clothing.
• Carry an auxiliary light and emergency supplies.
• Make sure the headlamp, mounting bracket and Li-Ion
battery are securely fastened.
• Always disconnect the battery from the headlamp when
transporting the light system.

MOUNTING THE HEADLAMP ON A HANDLEBAR
Depending on the size of your bike’s handlebars, use one of the
three “O-Ring” style mounting straps to attach the headlamp/
handlebar mount assembly. Follow the steps below:
1. To keep the overall height of the
MiNewt Pro Headlamp down, the
headlamp and mount are very
close to each other.
2. To install the mounting strap, loosen the
handlebar mount screw and rotate the
mount to expose the front slot.
3. Place the desired mounting strap
into the front slot making sure the
tab is pointed in the correct direction.
4. Before tightening the handlebar
mount screw, place the headlamp/mounting
assembly onto the handlebar and aim the
light. Once the headlamp is aimed,
securely tighten the handlebar mount
securely tighten.
5. Place the headlamp/mounting
assembly on the handlebar.
Pull/stretch the mounting strap under
the handlebar, towards the back and
loop it over and into the back slot.
6. Once properly mounted, the headlamp
should feel secure and not slip around
the handlebar.
MOUNTING THE HEADLAMP ON A HELMET
1. Unclamp the straps on each side of the helmet mount
and pull them free.
2. Position the plastic mounting plate
as close to the centerline of the
helmet as possible, orienting the
parallel grooves on the slider clip to
the rear.
3. Feed each strap into and out of two
helmet vents, circling each strap
back to the upper edge of the
corresponding clamp.
4. Fasten the straps by inserting them into the clamps.
INSTALLING SLIDER
Before using the MiNewt Pro in the helmet mount, you must rst
remove the handlebar mount and install the provided slider.
Remove the Phillips screw
that holds the handlebar mount
onto the back of the headlamp.
Be careful not to lose the
at and lock washer. Place
the slider onto the headlamp
and thread the Phillips screw
with the two washers into the
headlamp. Make sure the slider
is centered, then securely
tighten the Phillips screw.
INSERTING THE HEADLAMP INTO THE HELMET MOUNT
Insert the headlamp into the handlebar or helmet
mount slider clip from the rear
forward. Gently rocking the
lamp as you slide it may help.
Do not push the release lever
when inserting the headlamp
into the slider clip; let the lamp
snap into place by itself.
To remove the headlamp, push
the release lever and slide the
lamp backward.
Note: After mounting the
headlamp, adjust it so the
beam illuminates the road properly without distracting oncoming
riders.
OPERATION
1. Connect the headlamp cord to the Power Module.
2. Press and release the headlamp power button to turn the
light on. Cycle through the three brightness levels by
pressing and releasing the power button.
3. To access the daylight visible ash mode, and walk mode,
press and hold the power button until the headlamp starts
to ash.
4. With the headlamp in ash mode, press and release the power
button to access walk mode. From walk mode you can
power normal mode by pressing & releasing the power button.
5. To turn the headlamp off from normal, ash or walk modes,
press and hold the power button until the headlamp shuts off.
PROTECTING YOUR INVESTMENT
Properly charge your battery to maximize its lifespan (see the
“Battery Charging and Care” section for detailed information).
The MiNewt Pro 750 will perform in wet weather conditions, but
submerging it in water will damage the system.
SUPPORT
If you experience difculties during product installation or
operation, NiteRider provides free telephone support on
weekdays from 8:00 AM to 4:30 PM (PST) at 800.466.8366,
ext 4. You may also e-mail us at [e-mail].
WARRANTY
NiteRider stands behind its products with the following MiNewt
Cordless warranties:
• Lifetime warranty on all mechanical components
• 2 years on electrical components
• 180 days on rechargeable batteries
To obtain warranty service, it is preferable to have your
original sales receipt. Contact the NiteRider customer service
department at [phone], extension 4 to obtain a Return
Merchandise Authorization (RMA) number. The RMA number
must be prominently displayed on the outside of your package.
The product must be properly packaged to prevent damage
in transit. For complete warranty information, please visit our
website at www.niterider.com.
RUN TIMES
Light Level
High
Med
Low
Walk
Time*
1:30
2:30
5:00
10:00
Lumens
750
500
200
100
The MiNewt Pro 750 will run up to:
*Run times are approximations and will vary.
NiteRider Technical Lighting Systems, Inc.
8295 Aero Place, Suite 200
San Diego, CA 92123
6. It is highly recommended to disconnect the battery from the
headlamp when transporting the light system to prevent
accidentally turning on the headlamp which may cause
overheating and potential damage from high heat or
even a risk of re.