Nivea Selfie User manual
USERMANUAL
Getting Started with
Selfie
Mobile skin diagnosis system
Contents
•About Selfie & Components
•Turn on and off the device
•Sleep mode
•Re-booting the device
•Connect to a Wi-Fi network
•Change to USB mode
•Charge the device
USERMANUAL
Battery LED color
70~100 Blue
35~70 Violet
5~35 Red
0~5 Red (blinking)
About Selfie
Power button
LED
for battery status
Camerabutton
MicroUSBslot
Moisturesensor
Optic
Stander Selfie USBcable
DCadopterandplug
(2USBslots)
QuickStartGuide
Components
Turn on and off the device
1. Push the power button to left. After 3 seconds,
green LED blinks on.
2. Green LED is kept on when the device is ready
to connect with your host device.
3. After turning on, the LED displays the
remaining battery amount.
USERMANUAL
Rubber
USERMANUAL
1. The device goes to sleep mode after 10
minutes without using the device.
(No LED displayed)
2. Turn the device over to wake up from sleep
mode.
Sleep mode
1. Press the camera button for 7 seconds. 2. The LED blinks on Red →Green →Blue →Red.
And then, the green LED blinks on again.
Re-booting the device
3. The green LED blinks on.
* The Wi-Fi is connected automatically after re-booting the device.
3. After turning on, the LED displays the
remaining battery amount.
How to change the LED color
Battery LED color
70~100 Blue
35~70 Violet
5~35 Red
0~5 Red (blinking)
USERMANUAL
1. Check the SSID of the device written on the
serial label.
2. On the Wall paper of your host device, Apps →
Settings →Wi-Fi. Turn on the Wi-Fi (Drag the
on/off bar to right).
Connect to a Wi-Fi network
3. Select the SSID from the Wi-Fi networks list.
Enter a password if any, and tap Connect.
Change to USB mode
1. Turn off the device, and connect to your PC (or
tablet) by USB cable.
2. Press the camera button and turn on the device.
Keep pressing the camera button until the blue
LED of optic blinks on three times.
3. The LED is changed to blue, and the device is
recognized as a removable disk in your PC (or
tablet).
* Default: Wi-Fi mode.
Model CND
S/N CNDRIHSCO001
O/N NDA00000
SSID
X
XXXXXXXX
Seriallabel
Keeppressing
LEDblinking
(3 times)
* In case using USB hub, recommend to use the additional power of USB hub..
USERMANUAL
1. Connect the device to power adopter by USB
cable.
2. While charging the device, the blue LED blinks
on.
Charge the device
3. The blue LED is on when charging is completed.
* Only use the chargers, batteries, and cables approved by the supplier. Unapproved adaptors
or cables can cause the battery to explode or damage the device.
Operatingsystem Android4.0 (ICS)
Dual Camera Device:5MPixel CMOS
Diagnostic:5MPixel/Optical
zoom
Sensor Hydrationsensor
Connectivity
Wi‐Fi(IEEE802.11b/g/n)
USB2.0
Weight Approx 150g
Dimension 158x70x16.5mm
Display 4.5”1280x720HDMulti‐touchLCD
CPU 1.4GHzQuad‐core(ARMCortex‐A9)
SPECIFICATIONS
Memory Flash:16GBEmmc 4.51
RAM:1GBLPDDR2
InternalStorage 14GB
Externalmemory
support MicroSD (Optional)
Battery RechargeableLi‐Polymer
2,000mAh
Multi‐LED WhiteLED,PolarizedWhiteLED,
UVLED
MultimediaCapable H.263/H.264,MPEG‐4
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
,03257$17127(
)&&5)5DGLDWLRQ([SRVXUH6WDWHPHQW
7KLVHTXLSPHQWFRPSOLHVZLWK)&&UDGLDWLRQH[SRVXUHOLPLWVVHWIRUWKIRUDQXQFRQWUROOHGHQYLURQPHQW
7KLVHTXLSPHQWVKRXOGEHLQVWDOOHGDQGRSHUDWHGZLWKPLQLPXPGLVWDQFHFPEHWZHHQWKHUDGLDWRU\RXUERG\
7KLVWUDQVPLWWHUPXVWQRWEHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHU
Table of contents
