Nobles Typhoon 16B Product manual

ESPAÑOLENGLISH
MANUAL DEL OPERADOR Y REPUESTOS
OPERATOR AND PARTS MANUAL
WET/DRY BATTERY VACUUM
BATERÍA EN ASPIRACIÓN HÚMEDA/SECA
®
608819
Rev. 03 (11-2008)
*608819*
www.nobles.com
TYPHOON 16B
Model Part No.:
608817
608818 -- PAC
t

OPERATION
2Typhoont16B (11--08)
This manual is furnished with each new model.
It provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine care instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,
old machine components such as
batteries, hazardous fluids, including
antifreeze and oil, in an
environmentally safe way according to
local waste disposal regulations.
Always remember to recycle.
TENNANT Company
PO Box 1452
Minneapolis, MN 55440 USA
Phone: [phone] or (763) 513--2850
www.nobles.com
Specifications and parts are subject to change without notice.
Copyright E1999, 2003, 2004, 2008 TENNANT Company,
All rights reserved. Printed in U.S.A.
MACHINE DATA
Please fill out at time of installation
for future reference.
Model No. --
Serial No. --
Machine Options --
Sales Rep. --
Sales Rep. phone no. --
Customer Number --
Installation Date --

OPERATION
Typhoont16B (08--07) 3
TABLE OF CONTENTS (ESPAñOL ÍNDICE....18)
SAFETY PRECAUTIONS 4....................
SAFETY LABELS 5...........................
MACHINE COMPONENTS 6...................
MACHINE INSTALLATION 7...................
UNCRATING MACHINE 7..................
INSTALLING BATTERIES 7................
ATTACHING OPTIONAL SQUEEGEE KIT 7..
MACHINE SETUP 9..........................
WET VACUUMING 9......................
DRY VACUUMING 9.......................
MACHINE OPERATION 9.....................
VACUUM MOTOR THERMAL PROTECTOR 9
OPERATING ACCESSORY TOOLS 10.......
OPERATING SQUEEGEE KIT OPTION 10....
DRAINING RECOVERY TANK 10................
CHARGING BATTERIES 11....................
MACHINE MAINTENANCE 12..................
DAILY MAINTENANCE 12...................
MONTHLY MAINTENANCE 13...............
QUARTERLY MAINTENANCE 13............
BATTERY MAINTENANCE 13...............
TRANSPORTING MACHINE 14.................
STORING MACHINE 14........................
RECOMMENDED STOCK ITEMS 14.............
TROUBLE SHOOTING 15......................
MACHINE SPECIFICATIONS 16................
MACHINE DIMENSIONS 16....................
ELECTRICAL DIAGRAM 33....................
PARTS LIST 34...............................
TANK GROUP 34..........................
BASE GROUP 36..........................
OPTIONS 38..................................
SQUEEGEE KIT ASSEMBLY 38.............
WET/DRY TOOL KIT 40.....................
DRY TOOL KIT 41..........................
STANDARD FLOOR TOOL KIT 42...........
WET PICK--UP TOOL KIT 43................

OPERATION
4Typhoont16B (12--04)
SAFETY PRECAUTIONS
This machine is intended for commercial use.
It is designed for wet/dry vacuuming in an indoor
environment and is not constructed for any other
use. Use only recommended accessory tools.
All operators must read, understand and practice
the following safety precautions.
The following warning alert symbol and the “FOR
SAFETY” heading are used throughout this manual as
indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
Failure to follow these warnings may result in:
personal injury, electrical shock, fire or explosion.
WARNING: Fire Or Explosion Hazard:
-- Do Not Operate Machine In Or Near Flammable
Liquids, Vapors Or Combustible Dusts.
This machine is not equipped with an explosion
proof motor. The electric motor will spark upon
start up and during operation which could cause a
flashfireorexplosionifmachineisusedinanarea
where flammable vapors/liquids or combustible
dusts are present.
-- Do Not Pick Up Flammable Or Toxic Materials,
Burning Or Smoking Debris.
-- Batteries Emit Hydrogen Gas. Keep Sparks
And Open Flame Away. Keep Battery
Compartment Open When Charging.
WARNING: Electrical Shock Hazard.
Disconnect Battery Cables Before Servicing
Machine.
The following information signals potentially
dangerous conditions to the operator or
equipment:
FOR SAFETY:
1. Do not operate machine:
-- With flammable liquids or near flammable
vapors as an explosion or flash fire may
occur.
-- Unless trained and authorized.
-- Unless operator manual is read and
understood.
-- If not in proper operating condition.
-- In standing water.
-- Without bag and/or filters in place.
2. Before operating machine:
-- Make sure all safety devices are in place
and operate properly.
3. When using machine:
-- Do not pick up burning or smoking debris,
such as cigarettes, matches or hot ashes.
-- Report machine damage or faulty
operation immediately.
-- Never allow children to play on or around.
4. Before leaving or servicing machine:
-- Stop on level surface.
-- Turn machine off.
5. When servicing machine:
-- Disconnect battery connections before
working on machine.
-- Wear protective gloves and eye protection
when handling batteries or battery cables.
-- Avoid contact with battery acid.
-- Use manufacturer supplied or approved
replacement parts.
-- All repairs must be performed by a
qualified service person.
-- Do not modify the machine from its
original design.
6. When transporting machine:
-- Turn machine off.
-- Do not lift machine when batteries are
installed.
-- Get assistance when lifting machine.
-- Use a recommended ramp when
loading/unloading on/off truck or trailer.
-- Use tie--down straps to secure machine to
truck or trailer.

OPERATION
Typhoont16B (11--08) 5
SAFETY LABELS
The safety labels appear on the machine in the locations indicated. Replace labels if they are missing or become
damaged or illegible.
WARNING LABEL --
LOCATED ON BACK SIDE OF MACHINE.
FOR SAFETY LABEL --
LOCATEDONBACK
SIDE OF MACHINE.
FOR SAFETY:
Read the owner’s manual
before using machine.
WARNING: FAILURE TO
FOLLOW THESE WARNINGS
MAY RESULT IN: PERSONAL
INJURY, ELECTRICAL SHOCK,
FIRE OR EXPLOSION.
Do Not Operate Machine In Or
Near Flammable Liquids,
Vapors Or Combustible Dusts.
Do Not Pick Up Flammable Or
Toxic Materials, Burning Or
Smoking Debris.
WARNING LABEL -- LOCATED ON TOP OF THE MACHINE.

OPERATION
6Typhoont16B (11--08)
MACHINE COMPONENTS
5
89
6
4
7
1
32
1. Bag Compartment Cover
2. Vacuum Hose Snout
3. Control Grips
4. 145 cm (57 in) Vacuum Hose
5. Vacuum Bag Compartment /
Recovery Tank
6. Battery Compartment
7. Compartment Latches
8. Swivel Casters & 300 mm (12 in) Rear Wheels
9. Squeegee Kit (Optional)
3
10
11
12
14
13
10. Machine ON/OFF Switch
11. Drain Hose
12. Squeegee Kit Lift Pedal (Optional)
13. Charger Plug
14. 3 m (10 ft) Vacuum Hose

OPERATION
Typhoont16B (11--08) 7
MACHINE INSTALLATION
UNCRATING MACHINE
Carefully check carton for signs of damage. Report
damages at once to carrier.
Check Machine Contents to ensure package is
complete. Contact distributor for missing items.
Machine Contents:
1 -- Battery Cable #130364
4 -- Battery Post Caps #45962
4 -- Black Battery Boots #611221
1 -- 3m (10 ft) Vacuum Hose #160481
1 -- 145 cm (57 in) Vacuum Hose #1014026
1 -- Paper Bag #611785
1 -- Cloth Bag #900105
2 -- 12VDC 105AH Batteries #578426 (included with
machine PAC #607623)
1 -- Battery Charger, 24DC/12A 120V #603553
(included with machine PAC #607623)
NOTE: Squeegee and Accessory Tools Kits are
optional, they must be ordered separately (See
OPTIONS section).
INSTALLING BATTERIES
NOTE: If planning to install Optional Squeegee Kit,
wait to install the batteries until kit is installed
(See ATTACHING OPTIONAL SQUEEGEE KIT).
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks And
Open Flame Away. Keep Battery Compartment
Open When Charging.
FOR SAFETY: When servicing machine, wear
protective gloves and eye protection when
handling batteries or battery cables. Avoid contact
with battery acid.
Recommended Battery Specifications:
Two 12 volt 105/130 amp hour deep cycle batteries.
Maximum battery dimensions are 340 mm (13.5 in) L x
180 mm (7 in) W x 250 mm (10 in) H.
1. Turn ON/OFF switch to off.
ATTENTION: Make sure tanks are empty before
opening.
2. Open battery compartment, unlatch lower latches
and carefully tilt upper housing backwards to floor.
Remove loose battery cables at bottom of
compartment (Figure 1).
FIG. 1
3. Carefully install batteries into compartment and
arrange battery posts as shown. Connect the
battery cables to the battery posts as shown, RED
TO POSITIVE & BLACK TO NEGATIVE. Use the
battery post covers and rubber boots supplied
(Figure 2).
(--)
(+)
(--)
(+)
FIG. 2
ATTENTION: Do not drop batteries into
compartment. Battery and machine housing
damage may result.
4. Apply a light coating of non--metallic grease or
protective spray on the cable connections to
prevent battery corrosion.
ATTACHING OPTIONAL SQUEEGEE KIT
NOTE: Kit installation is made easy if batteries are not
installed. However, kit can be installed with batteries in
place.
1. Remove vacuum bags and/or empty recovery
tank.
2. Tip machine on backside -- only if batteries are
removed from machine.

OPERATION
8Typhoont16B (11--08)
3. Remove two unused squeegee mounting screws
from bottom of machine.
4. Install squeegee mounting bracket as shown.
Secure with screw and washers that you removed
(Figure 3).
FIG. 3
5. Fasten squeegee bracket to mounting bracket.
Use two (2) clevis and cotter pins provided
(Figure 4).
FIG. 4
6. Stand machine upright.
7. Insert spacer through hole in pedal then position
pedal between two holes in squeegee bracket.
Secure with hardware provided (Figure 5).
FIG. 5
8. Slide pedal between the two mounting arms on
back of machine. Align and insert clevis pin
through arms and slot in pedal, secure with cotter
pin (Figure 6).
FIG. 6
9. Attach squeegee assembly to bracket as shown
and secure with two thumb screws (Figure 7).
FIG. 7
10. Connect the 145 cm (57 in) vacuum hose to the
squeegee assembly and to cover snout.Loop the
hose as shown using the hose clip provided
(Figure 8).
FIG. 8

OPERATION
Typhoont16B (12--04) 9
MACHINE SETUP
WET VACUUMING
1. Open machine cover and remove vacuum bag
from recovery tank (Figure 9).
FIG. 9
2. Make sure automatic float shut-off screen is in
place (Figure 10).
FIG. 10
ATTENTION: To prevent vacuum motor damage,
automatic float shut-off screen must be in place.
DRY VACUUMING
1. Open machine cover and install cloth filter bag,
make sure that the bag edge is properly seated on
compartment rim (Figure 11).
For easy debris disposal and to increase the life of
cloth filter bag, use a paper vacuum bag with the
cloth bag. Place the paper bag inside of cloth bag
and tuck the top of paper bag around outside rim
of cloth bag. Never use paper bag without cloth
filter bag in place. Do not reuse paper bags --
always dispose.
FIG. 11
ATTENTION: Always make sure that a bag is in
place before dry vacuuming. Operating machine
without bag in place will damage vacuum motor.
This damage is NOT covered by warranty.
2. Close cover and fasten latches.
3. Leave automatic float shut--off screen in place
when dry vacuuming. It can provide limited
vacuum motor protection for a faulty bag.
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
WARNING: Fire Or Explosion Hazard. Do Not
Operate Machine In Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
WARNING: Fire Or Explosion Hazard. Do Not
Pick Up Flammable Or Toxic Materials, Burning Or
Smoking Debris.
VACUUM MOTOR THERMAL PROTECTOR
The vacuum motor is thermally protected by a
temperature sensor device. It will trip if motor has an
overload. If motor should quit, wait 20 minutes for
motor to cool and remove obstruction before
continuing.

OPERATION
10 Typhoont16B (10--03)
OPERATING ACCESSORY TOOLS
1. Connect 3m (10 ft) vacuum hose to machine cover
snout.
2. Select desired accessory tool and connect to
vacuum hose (Figure 12).
FIG. 12
3. Activate ON/OFF switch and operate accessory
tool as normal.
4. During DRY vacuuming, check bag periodically for
fullness. For best suction performance, empty bag
at 3/4 full.
During WET vacuuming, the float shut-off screen
will automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If you are vacuuming up liquids that
may cause foaming inside recovery tank, use a
quality defoamer chemical to eliminate the foam.
Foam will NOT shut off automatic float and will
damage vacuum motor. Damage due to foam is
NOT covered by warranty.
OPERATING SQUEEGEE KIT OPTION
1. Lower squeegee to floor, lightly kick the pedal
forward to release from transport position
(Figure13).
FIG. 13
2. Activate the ON/OFF switch.
3. Begin operating by pushing and pulling machine in
either direction.
4. During operation, the float shut-off screen will
automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If you are vacuuming up liquids that
may cause foaming inside recovery tank, use a
quality defoamer chemical to eliminate the foam.
Foam will NOT shut off automatic float and will
damage vacuum motor. Damage due to foam is
NOT covered by warranty.
5. To raise squeegee, step downward on pedal until
pedal engages in the transport position
(Figure 14).
FIG. 14
NOTE: Squeegee Kit can be used to pick up fine
particles (dust, sand, sawdust, etc...). The squeegee
is not recommended for ordinary dry pick up.
DRAINING RECOVERY TANK
1. Push machine to nearest floor drain, if not
available use a bucket to drain machine.
2. Remove drain hose from holder and twist off drain
hose cap and drain. Raise hose to stop flow of
water (Figure15).
FIG. 15

OPERATION
Typhoont16B (12--04) 11
3. After draining recovery tank, open cover and
thoroughly rinse out tank with clean water.
4. Replace drain hose knob securely and return to
holder.
ATTENTION: Be certain drain hose knob is secure
to prevent suction loss.
CHARGING BATTERIES
ATTENTION: To prolong the life of the batteries
and to provide optimum machine performance,
ONLY recharge the batteries after a total of 30
minutes of use or more. Do not leave batteries
discharged for lengthy periods.
The following charging instructions are intended for
battery chargers supplied with the machine. Only use
a battery charger with the following specifications to
prevent battery damage.
CHARGER SPECIFICATIONS:
SOUTPUT VOLTAGE - 24 VOLTS
SOUTPUT CURRENT - 15 AMPS
SAUTOMATIC SHUTOFF CIRCUIT
SFOR DEEP CYCLE BATTERY CHARGING
1. Push the machine to a flat, dry surface in a well--
ventilated area for charging.
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks And
Open Flame Away. Keep Battery Compartment
Open When Charging.
2. Open battery compartment. Unlatch lower latches
at front of machine and carefully tilt upper housing
backwards to floor (Figure 16).
NOTE: Make sure to drain the tank prior to accessing
the batteries.
FIG. 16
3. Before charging the batteries, check the
electrolyte level in each battery cell (Figure 17).
FIG. 17
FOR SAFETY: When servicing machine, wear
protective gloves and eye protection when
handling batteries or battery cables. Avoid contact
with battery acid.
The electrolyte level (A) should slightly cover the
battery plates (B). Add distilled water as needed.
DO NOT OVERFILL, the fluid may expand and
overflow while charging. Replace cell caps before
charging (Figure 18).
A
B
FIG. 18
4. Connect the charger’s AC power supply cord to a
properly grounded receptacle (Figure 19).
Grounded
3HoleOutlet
Ground Pin
FIG. 19

OPERATION
12 Typhoont16B (12--04)
5. Connect the battery charger into the machine’s
charging receptacle as shown (Figure 20).
FIG. 20
6. The charger will automatically begin charging and
shut off when fully charged.
ATTENTION: Do not disconnect the charger’s DC
cord from the machine’s receptacle when the
charger is operating. Arcing may result. If the
charger must be interrupted during charging,
disconnect the AC power supply cord first.
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks And
Open Flame Away. Keep Battery Compartment
Open When Charging.
7. After charging, check the electrolyte level (A)
again. The level should be approximately 1 cm
(0.38 in) from the bottom of the fill--port (B)
(Figure 21). Add distilled water if needed.
DO NOT OVERFILL.
A
B
FIG. 21
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow the daily, monthly and quarterly maintenance
procedures.
WARNING: Electrical Shock Hazard.
Disconnect Battery Cables Before Servicing
Machine.
DAILY MAINTENANCE
(After Every Use)
1. Drain and rinse out recovery tank after wet
vacuuming.
2. Remove and rinse off the float shut-off screen
located in recovery tank (Figure 22).
FIG. 22
ATTENTION: Always have float shut--off screen in
place before operating. During wet operation, the
float shut--off screen protects the vacuum motor
from water. During dry vacuuming, the float
shut--off screen can provide limited protection for
a faulty filter bag.
3. Clean squeegee blades with a cloth. Replace
blades when they become worn.
4. Check bag for fullness, empty bag at 3/4 full.
5. Clean machine with an all purpose cleaner and
damp cloth.
FOR SAFETY: When cleaning machine, do not
power spray or hose off machine. Electrical
malfunction may occur.
6. Recharge the batteries after a total of 30 minutes
of use or more (See CHARGING BATTERIES).
7. Inspect vacuum hose regularly for holes, loose
cuff or clogged debris.

OPERATION
Typhoont16B (12--04) 13
MONTHLY MAINTENANCE
(Every80HoursofUse)
1. Check the fluid level in each battery cell
(See BATTERY MAINTENANCE).
2. Clean battery tops to prevent corrosion
(See BATTERY MAINTENANCE).
3. Check for loose or corroded battery cables.
4. To maintain maximum performance, wash the
cloth filter bag by hand with a mild detergent. Let
bag dry thoroughly before replacing.
5. Lubricate wheels and front swivel casters with a
water resistant oil.
6. Check machine for loose nuts and bolts.
QUARTERLY MAINTENANCE
(Every 250 Hours of Use)
Check the motor for carbon brush wear. Replace
carbon brushes when worn to a length of 10 mm
(0.38 in) or less.
Contact an Authorized Service Center for
machine repairs.
WARNING: Electrical Hazard. Disconnect
Battery Cables Before Servicing Machine.
BATTERY MAINTENANCE
WARNING: Fire Or Explosion Hazard.
Batteries Emit Hydrogen Gas. Keep Sparks And
Open Flame Away. Keep Battery Compartment
Open When Charging.
FOR SAFETY: When servicing machine, wear
protective gloves and eye protection when
handling batteries and battery cables. Avoid
contact with battery acid.
1. Check the specific gravity using a hydrometer to
determine the charge level and the condition of the
batteries (Figure 23). If one or more of the battery
cells read lower than the other battery cells (0.050
or more), the cell is damaged, shorted, or is about
to fail. Check the hydrometer readings against the
following chart to determine the remaining battery
charge level.
NOTE: Do not take readings immediately after adding
distilled water. If the water and acid are not thoroughly
mixed, the readings may not be accurate.
FIG. 23
SPECIFIC GRAVITY
at 27_C(80_F) BATTERY
CHARGE
1.265 100% CHARGED
1.223 75% CHARGED
1.185 50% CHARGED
1.148 25% CHARGED
1.110 DISCHARGED
NOTE: If the readings are taken when the battery
electrolyte is any temperature other than 27_C(80_F),
the reading must be temperature corrected. Add or
subtract to the specific gravity reading 0.004, 4 points,
for each 6_C(43_F) above or below 27_C(80_F).
2. Always follow proper charging instructions
(See CHARGING BATTERIES).
3. Check the electrolyte level (A) in each battery cell
after charging batteries. The level should be
approximately 1 cm (0.38 in) from the bottom of
the fill--port (B) (Figure 24). Add distilled water if
needed. DO NOT OVERFILL.
A
B
FIG. 24

OPERATION
14 Typhoont16B (12--04)
4. Keep the battery tops clean to prevent battery
corrosion.
To clean batteries:
FOR SAFETY: When servicing machine, wear
protective gloves and eye protection when
handling batteries and battery cables. Avoid
contact with battery acid.
a. Mix a strong solution of baking soda and water
(Figure 25).
FIG. 25
b. Brush the solution sparingly over the battery
tops and cable connectors.
NOTE: Do not allow baking soda solution to enter
battery cells.
c. Use a wire brush to clean the battery terminals
and cable connectors.
d. After cleaning, apply a coating of clear battery
post protectant to the terminals and cable
connectors.
5. Check for loose or worn cables. Replace if worn.
TRANSPORTING MACHINE
When transporting machine by use of trailer or truck,
be certain to follow tie--down procedures below:
FOR SAFETY: When using machine, go slow on
inclines and slippery surfaces.
1. Load the machine using a recommended loading
ramp.
2. Position the front of machine up against the front
ofthetrailerortruck.
3. Place a block behind each rear wheel to prevent
machine from rolling.
4. Place tie--down straps over top of machine to
prevent it from tipping. It may be necessary to install
tie--down brackets to the floor of your trailer or truck.
FOR SAFETY: When transporting machine, use a
recommended ramp when loading/unloading
on/off truck or trailer, use tie--down straps to
secure machine to truck or trailer.
STORING MACHINE
Before storing the machine perform the following
instructions below:
1. Empty and rinse out recovery tank and accessory
tools.
2. Empty or replace vacuum bag.
3. Raise or remove squeegee assembly.
4. Store machine in a dry area in the upright position.
5. Disconnect battery cables if storing for a lengthy
period.
ATTENTION: Do Not Expose Machine To Rain.
Store Indoors.
ATTENTION: If storing machine in freezing
temperatures, be certain to drain machine of all
water. Damage due to freezing is not covered by
warranty.
RECOMMENDED STOCK ITEMS
Refer to the Parts List section in this manual for
recommended stock items. Stock Items are clearly
identified with a bullet preceding the parts description.
See example below:

OPERATION
Typhoont16B (10--03) 15
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
No power. Faulty ON/OFF switch. Contact Service Center.
Batteries need charging. See CHARGING BATTERIES.
Faulty battery(s). Replace battery(s).
Loose battery cable. Tighten loose cables.
Improper battery cable connection. See INSTALLING BATTERIES.
Vacuum motor thermal overload
tripped. Check air flow for obstruction, wait 20 minutes for motor to cool.
Faulty vacuum motor wiring. Contact Service Center.
Poor pickup. Air flow obstruction. Remove obstruction from float shut--off screen,
vacuum hose, accessary tool or squeegee.
Vacuum bag is full. Empty or replace bag.
Float shut--off screen is activated. Drain recovery tank.
Drain hose plug is loose or off. Secure drain hose plug.
Cover latches are not engaged. Engage cover latches.
Batteries need charging. Charge batteries.
Worn cover gasket. Replace gasket.
Vacuum motor carbon brushes worn. Contact Service Center.
Short run time. Batteries not fully charged. Charge batteries.
Faulty battery(s). Replace battery(s).
Batteries need maintenance. See BATTERY MAINTENANCE.
Faulty charger. Replace charger.

OPERATION
16 Typhoont16B (11--08)
MACHINE SPECIFICATIONS
Model TYPHOONt16B
LENGTH 840 mm (33 in)
WIDTH 530 mm (21 in)
HEIGHT 1090 mm (43 in)
WEIGHT / WEIGHT WITH BATTERIES 41 Kg (90 lbs) / 107 Kg (235 lbs)
RECOVERY TANK CAPACITY 60.75 L (16 Gal)
VACUUM BAG CAPACITY Cloth 15.5 cubic liters (0.44 bushels)
Paper 22.7 cubic liters (0.65 bushels)
VACUUM MOTOR 24V, 3--stage, .75hp, 23A, 566W
OPTIONAL SQUEEGEE PATH WIDTH 685 mm (27 in)
864 mm (34 in)
1016 mm (40 in)
AIRFLOW / SEALED WATER LIFT 70 cfm (1.98 m3/h) / 1780 mm (70 in)
BATTERIES 2--12V deep cycle lead acid, 105AH or 130AH
RUN TIME, CONTINUOUS up to 4 hours
DECIBEL RATING AT OPERATOR’S EAR, INDOORS ON TILE >70dB(A)
MACHINE DIMENSIONS
1090 mm
(43 in)
(See Specifications Chart)
Optional Squeegee Kit
840 mm (33 in)
530 mm (21 in)

OPERACIÓN
Typhoont16B (11--08) 17
Este manual se proporciona con cada nuevo modelo.
Proporciona instrucciones necesarias de
mantenimiento y lista ilustrada de piezas.
Antes de operar o prestar servicio a la máquina,
lea completamente este manual y entienda la
máquina.
Para ordenar piezas use las Listas Ilustradas de las
Piezas. Asegúrese de tener listo el número de modelo
y de serie de la máquina, antes de ordenar piezas o
suministros. Las piezas y suministros pueden
ordenarse por teléfono o por correo de cualquier
centro autorizado de piezas y servicio, distribuidor o
de cualquiera de las subsidiarias del fabricante.
Esta máquina proporcionará un servicio excelente. Sin
embargo, los mejores resultados se obtienen a un
costo mínimo si:
SLa máquina se opera con un cuidado razonable.
SLa máquina se mantiene con regularidad, según las
instrucciones de mantenimiento provistas.
SLa máquina se mantiene con las piezas provistas
por el fabricante o equivalentes.
PROTECCIÓN DEL MEDIO
AMBIENTE
Deseche el material de embalaje, los
componentes usados de la máquina
como las baterías y los líquidos
peligrosos como el anticongelante y el
aceite, de forma segura para el medio
ambiente, de acuerdo con las
normativas o disposiciones locales.
No olvide reciclar.
TENNANT Company
PO Box 1452
Minneapolis, MN 55440
Phone: [phone] or (763) 513--2850
www.nobles.com
Las características técnicas y las piezas están sujetas a
modificaciones sin previo aviso.
Copyright E1999, 2003, 2004, 2008 TENNANT Company,
Todos los derechos reservados. Impreso en U.S.A.
DATOS DE LA MÁQUINA
Rellénela cuando realice la instalación para
utilizarla como referencia en el futuro.
Nº modelo:
Nº serie:
Opciones de la máquina:
Vendedor: --
Nº de teléfono del vendedor:
Nº de cliente:
Fecha de instalación:

OPERACIÓN
18 Typhoont16B (11--08)
ÍNDICE
MEDIDAS DE SEGURIDAD 19..................
ADHESIVOS DE SEGURIDAD 20...............
COMPONENTES DE LA MÁQUINA 21...........
INSTALACIÓN DE LA MÁQUINA 22.............
DESEMPAQUE DE LA MÁQUINA 22.........
INSTALACIÓN DE LAS BATERÍAS 22........
ADICION DE EQUIPO ESCURRIDOR
OPCIONAL 23.............................
PREPARACIÓN DE LA MÁQUINA 24............
ASPIRACIÓN DE LÍQUIDOS 24..............
ASPIRACIÓN EN SECO 24..................
OPERACIÓN DE LA MÁQUINA 25..............
PROTECTOR TÉRMICO DEL MOTOR DE
ASPIRACIÓN 25...........................
HERRAMIENTAS ADICIONALES DE
OPERACIÓN 25...........................
OPERACIÓN DE LA OPCION DEL JUEGO
ESCURRIDOR 25..........................
VACIADO DEL DEPÓSITO DE
RECUPERACIÓN 26...........................
CARGA DE LAS BATERÍAS 26.................
MANTENIMIENTO DE LA MÁQUINA 28.........
MANTENIMIENTO DIARIO 28...............
MANTENIMIENTO MENSUAL 28............
MANTENIMIENTO TRIMESTRAL 28.........
MANTENIMIENTO DE LA BATERÍA 28.......
TRANSPORTE DE LA MÁQUINA 30.............
ALMACENAMIENTO DE LA MÁQUINA 30.......
STOCK RECOMENDADO DE REPUESTOS 30...
LOCALIZACIÓN DE FALLAS 31................
ESPECIFICACIONES DE LA MÁQUINA 32.......
DIMENSIONES DE LA MÁQUINA 32............
DIAGRAMAS ELECTRICAS 33.................
LISTA DE PIEZAS 34..........................
CONJUNTO DEL TANQUE 34...............
GRUPO BASE 36..........................
OPCIONES 38................................
PIEZAS DE LA RASQUETA DE CAUCHO 38..
KIT DE HERRAMIENTA SECO MOJADO 40...
KIT DE HERRAMIENTA SECO 41............
KIT DE HERRAMIENTA ESTÁNDAR 42.......
KIT DE HERRAMIENTA MOJADO 43.........

OPERACIÓN
Typhoont16B (12--04) 19
MEDIDAS DE SEGURIDAD
Esta máquina es para el uso comercial. Se ha
diseñado para aspiración húmeda/seca en un
ambiente interior y no se construye para ningún
otro uso. Use sólo las herramientas adicionales
recomendadas.
Todos los operadores deben leer, entender y
practicar las precauciones siguientes de
seguridad.
A lo largo de todo el manual se utilizan los siguientes
símbolos de advertencia y encabezados “PARA SU
SEGURIDAD” descritos a continuación:
ADVERTENCIA: Para advertir de riesgos o
prácticas inseguras que podrían resultar en
lesiones personales graves o la muerte.
PARA SU SEGURIDAD: Para identificar acciones
que deben seguirse para el funcionamiento
seguro del equipo.
El no cumplimiento de estas advertencias puede
causar lesiones personales, descargas eléctricas,
incendios y explosiones.
ADVERTENCIA: Peligro de incendio o
explosión:
-- No opere la máquina en o cerca de líquidos,
vapores inflamables o polvos combustibles.
Esta máquina no está equipada con motor a
prueba de explosión. El motor eléctrico emite
chispas al arrancar y durante el funcionamiento lo
que podría causar un fuego explosivo o explosión
si la máquina se usa en una área donde están
presentes vapores/líquidos inflamables o polvos
combustibles.
-- No recoja materiales tóxicos o inflamables ni
residuos humeantes o ardiendo.
-- Las baterías emiten hidrógeno. Mantenga
chispasyllamasalejadasdelamáquina.
Mantenga el compartimento de la batería
abierto mientras realiza la operación de carga.
ADVERTENCIA: Peligro choque eléctrico.
Desconecte los cables de la batería antes de
realizar reparaciones en la máquina.
La información siguiente señala condiciones
potencialmente peligrosas para el operador o el
equipo:
PARA SU SEGURIDAD:
1. No opere la máquina:
-- Con líquidos inflamables o cerca de los
vapores inflamables ya que puede ocurrir
una explosión o fuego explosivo.
-- A menos que está capacitado y autorizado.
-- A menos que se haya leído y entendido el
manual del funcionamiento.
-- Si no está en condición de ejecutar una
operación apropiada.
-- En agua estancada.
-- Sin haber colocado los filtros y/o la bolsa.
2. Antes de arrancar la máquina:
-- Asegúrese que todos los dispositivos de
seguridad están en su lugar y operando
apropiadamente.
3. Al usar máquina:
-- No recoja restos ardiendo o humeantes
como cigarrillos, cerillas o cenizas
calientes.
-- Informe inmediatamente acerca de daños
o una operación defectuosa de la
máquina.
-- Nunca permita que los niños jueguen en o
alrededor de la máquina.
4. Antes de salir de o reparar la máquina:
-- Deténgala en una superficie nivelada.
-- Apague la máquina.
5. Al prestar servicio a la máquina:
-- Desconecte las conexiones de la batería
antes de trabajar en la máquina.
-- Utilice guantes y gafas de protección al
trabajar con las baterías o sus cables.
-- Evite el contacto con el ácido de la batería.
-- Use piezas de repuesto provistas o
aprobadas por el fabricante.
-- Todas las reparaciones deben ser
realizadas por una persona de servicio
calificada.
-- No modifique la máquina de su diseño
original.
6. Al transportar máquina:
-- Apague la máquina.
-- No levante la máquina con las baterías
instaladas.
-- Obtenga ayuda al alzar la máquina.
-- Utilice una rampa al cargar/descargar la
máquina en/de un camión o remolque.
-- Use correas de amarre para asegurar la
máquina al camión o remolque.

OPERACIÓN
20 Typhoont16B (11--08)
ADHESIVOS DE SEGURIDAD
Los adhesivos de seguridad se encuentran en las posiciones indicadas a continuación. Sustituya los adhesivos si se
han desprendido, están deteriorados o son ilegibles.
ADHESIVO DE ADVERTENCIA -- Situado en la parte trasera de la máquina.
ADHESIVO DE ADVERTENCIA –
Situado en la parte trasera de la máquina.
ADHESIVO DE PARA SU SEGURIDAD –
Situado en la parte trasera de la máquina.
PARA SU SEGURIDAD:
Lea el manual antes de utilizar la máquina.
ADVERTENCIA: El no
seguir estas advertencias
puede resultar en: lesiones
personales, electrocución,
choque eléctrico, fuego o
explosión.
No opere la máquina en o
cerca de líquidos, vapores
inflamables o polvos com-
bustibles.
No recoja materiales tóxicos
o inflamables ni residuos
humeantes o ardiendo.