Nobles MONSOON Product manual

OPERATOR AND PARTS MANUAL
FLOOR STRIPPER APPLICATOR
®
608521
Rev. 01 (08-2007)
*608521*
TM
www.nobles.com
MONSOON
Model Part No.: 608520

OPERATION
2Monsoont(08--07)
This manual is furnished with each new model. It
provides necessary installation, operation and
maintenance instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine maintenance instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Please fill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-
E1999, 2007 Tennant Company Printed in the U.S.A.
Nobles is a registered United States trademark of Tennant Company.
TABLE OF CONTENTS
MACHINE APPLICATION 2................
MACHINE COMPONENTS 2...............
MACHINE INSTALLATION 3...............
UNCRATING MACHINE 3.................
ATTACHING HANDLE 3...................
ATTACHING SOLUTION FLOW LEVER
LINKAGE 3..............................
INSTALLING DISPENSER ASSEMBLY 3....
MACHINE SETUP 4........................
MACHINE OPERATION 4..................
DRAINING TANK 5.........................
MACHINE MAINTENANCE 5...............
TROUBLE SHOOTING 5...................
SPECIFICATIONS 5........................
PARTS LIST 6.............................
MAIN HOUSING ASSEMBLY 6.............
DISPENSER ASSEMBLY 8................
MACHINE APPLICATION
This machine is intended for commercial use. It is
suited to apply floor stripper solvent on floors in an
indoor environment and is not constructed for any
other use. Use only recommended stripping solvents.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
MACHINE COMPONENTS
1
2
3
4
6
5
7
12
9
10
13
11
8
14
1. Solution Flow Lever
2. Drain Hose Knob
3. Handle
4. 76L (20 Gallon) Solution Tank
5. Solution Tank Cover
6. Cover Latches
7. 250 mm (10 inch) Stair Climbing Wheels
8. Dispenser Frame Weldment
9. Dispenser Assembly
10. Dispenser Assembly Knobs
11. Drip Bar
12. Wall Rollers
13. Clear Solution Hose
14. Brushes

OPERATION
Monsoont(07--99) 3
MACHINE INSTALLATION
UNCRATING MACHINE
Carefully check carton for signs of damage. Report
damages at once to carrier.
Check carton contents list below to ensure everything
is included. Contact your distributor for missing items.
Contents:
-- Machine
-- Handle
-- Hardware package (stored in solution tank)
-- Dispenser Frame Weldment w/ Lift Pedal
-- Dispenser Assembly w/2 Knobs
-- 760 mm (30 in) Drip Bar
ATTACHING HANDLE
1. Attach handle to machine. Hardware package is
stored in solution tank.
2. Align handle to mounting holes and fasten with (4)
3/8x1--1/2” hex head screws with flat and lock
washers. Use a 9/16” wrench (Figure 1.).
(4) 3/8x1-1/2 Screw
(4) Lock Washers
(4) Large Flat Washers
FIG. 1.
ATTACHING SOLUTION FLOW LEVER LINKAGE
1. Connect solution flow lever to solution valve
linkage arm.
2. Align solution lever to linkage arm and connect
with allen screw, (2) small flat washer and nylon
lock nut. Use a 5/32” allen wrench and 7/16”
wrench (Figure 2.).
(2) Flat Washers
(1) Allen Screw
(1) Nylon Lock Nut
Solution Flow
Lever Linkage
FIG. 2.
INSTALLING DISPENSER ASSEMBLY
1. Place dispenser frame weldment under machine
and fasten to mounting bracket that is factory
installed. Use two clevis pins as shown, secure
with two hair pins (Figure 3.).
(2) Clevis Pins
Dispenser
Frame Weldment
(2)HairPins
FIG. 3.
2. Position pedal between pedal brackets at rear of
machine. Insert clevis pin through brackets and
pedal, secure with hair pin (Figure 4.).
Clevis Pin
Pedal
Brackets
Hair Pin
FIG. 4.

OPERATION
4Monsoont(11--99)
3. Loosen (2) knobs and attach dispenser assembly
to frame weldment, tighten down knobs. Brush
side should face towards machine (Figure 5.).
Knob
Dispenser
Assembly
Frame
Weldment
Brushes
FIG. 5.
4. Position drip bar into dispenser assembly and
snap bar onto retainer clip. Then connect elbow on
clear hose to drip bar (Figure 6.).
Drip Bar
Elbow
Retainer
Clip
FIG. 6.
5. Raise dispenser assembly off floor. Step down on
pedal to raise dispenser to transport position
(Figure 7.).
FIG. 7.
MACHINE SETUP
1. Push solution flow lever completely forward to
shut off solution flow.
2. Open solution tank cover and pour up to 76L (20
gal) of recommended stripper solvent into tank.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
NOTE: See Flow Rates on page 5.
WARNING: Flammable materials can cause
an explosion or fire. Do not use flammable
materials in tank(s).
MACHINE OPERATION
NOTE: This machine is designed to be pushed forward
for easy maneuvering and quick applying, however if
desired you may pull the machine backwards, but you
must rotate the dispenser assembly 180°.
1. Lower dispenser assembly to floor. Push pedal
forward to release from transport position
(Figure 8.).
FIG. 8.
NOTE: Use stripper traction shoes when applying
stripper on floor.
2. To start solution flow, pull Solution Flow Lever
completely backwards. You can regulate the
amount of flow by pushing lever forward
(Figure 9.).
Solution
Flow Lever
FIG. 9.

OPERATION
Monsoont(11--99) 5
3. Begin applying stripper by pushing machine at a
moderate walking pace.
FOR SAFETY: When using machine, go slow on
inclines and slippery surfaces.
DRAINING TANK
1. Raise dispenser assembly to transport position
and push machine to draining area.
2. To drain excess stripper solvent, remove drain
hose from holder and twist off drain hose plug.
3. Perform maintenance procedures before storing
machine.
MACHINE MAINTENANCE
AFTER EACH USE:
1. Remove and rinse out dispenser drip bar and
brushes.
2. Rinse out tank and clear hose thoroughly.
3. Clean machine housing with a nonabrasive,
non-solvent cleaner.
4. Periodically lubricate wheels and casters with a
water resistant oil.
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
No solution flow. Dispenser drip bar is plugged. Unplug drip bar.
Solution flow lever not activated. Activate lever.
Solution valve is plugged. Replace or unplug valve.
Clear hose is plugged. Remove and flush out.
SPECIFICATIONS
Model Monsoont
LENGTH 840 mm ( 33 in)
WIDTH 480 mm (19 in)
HEIGHT 860 mm (34 in)
WEIGHT 29Kg (64.5 lbs)
DISPENSER ASSEMBLY WIDTH 810 mm (32 in)
TANK CAPACITY 76L (20 Gal)
SOLUTION FLOW RATE 14L (3.6 Gal) per minute (max. flow)
2509 Sq. meter (27,000 Sq. ft) per full tank

PARTS LIST
6Monsoont(08--07)
MAIN HOUSING ASSEMBLY
8
61
1
4
3
5
7
6
26
25
24
23
22
9
10
11
11
18
12
15
13
16
17
48
49
47
17
50
28
29
30
31
32
33
27
34
35
36
40
41
14
19
22
23
24
4
58
57
56
55
48
49
50
51
52
53
62
49
48
45
44
43
46
42
38
39
54
12
60
16
15 12
59
15
16
20
15
21
63
37
2

PARTS LIST
7
Monsoont(08--07)
MAIN HOUSING ASSEMBLY
REF PART # DESCRIPTION QTY.
1608613 COVER, GREEN 1
2610722 LABEL, HZRD, FLAMMABLE MATL 1
3609980 SCREW, TRS, #8--32X0.38, PHL 4
449800 DLATCH, HOOD RUBBER 2
5601401 PLUG, DOME 1
6613233 DGASKET, 16 GAL COVER 1
7140802 SCREW, 8--32X5/8 4
828990 NUT, LOCK 8--32 4
9230318 HINGE, COVER 16 GAL 1
10 140000 WASHER, FLAT 1/4” 4
11 140195 SCREW, 1/4--20X1/2 8
12 601293 SCREW, 1/4--20X.312 3
13 140825 SCREW, #6X1/2 4
14 601285 BRACKET, PIVOT MOUNT 1
15 140027 WASHER, FLAT 5/16 6
16 41169 NUT, HEX, LOCK, .25--20, NL, SS 3
17 601283 PLATE, LINK 1
18 069764052 CLOSURE, HANDLE 1
19 601284 BRACKET, HANDLE 1
20 608618 HANDLE, GREEN 1
21 1028077 LABEL, READ MANUAL, ISO 1
22 140231 SCREW, 3/8X1--1/2 4
23 140017 WASHER, SPLIT LOCK 3/8” 4
24 140028 WASHER, FLAT 3/8” 4
25 611978 BRACKET, DRAIN HOSE 1
26 140825 SCREW, #6X1/2 2
∇27 701061 DASM, DRAIN HOSE STOPPER 1
Y28 230831 KNOB, DRAIN HOSE 1
Y29 230882 STRAP, DRAIN STOPPER 1
Y30 140056 WASHER, FNDR 3/8ID X 1.50OD 1
Y31 140955 PLUG, DRAIN HOSE 1
32 140921 SLEEVE, DRAIN HOSE 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEM
REF PART # DESCRIPTION QTY.
33 140072 CLAMP 2
34 160457 DHOSE, DRAIN, 25” 1
35 130041 WIRE TIE, NYLON 11--1/2X.190 1
36 11531 CLAMP, HOSE, WORMDRIVE,
1.06--2.00D, .56W
1
37 604604 SPACER, DISPENSER, VALVE 1
38 103019 DCAP, HUB 2
39 103068 DWHEEL, 10” X 1.75 GRAY HUB/TRD 2
40 630018 DHOSE, 1.00D 0.75B 33.0L 1
41 575745 FITTING, ELBOW, .75” HOSE .75” NPT 1
42 140063 WASHER, FLAT, 0.51B 1.25D .31, NYL 2
43 01696 SCREW, .25--20X0.50 4
44 140016 WASHER, LOCK 1/4” 4
45 230746 BRACKET, AXLE OFFSET 2
46 608908 AXLE, .5D X 19.17L 1
47 230496.BK SUPPORT, DRAIN HOSE 1
48 140885 SCREW,1/4--20X1/2 4
49 578244000 WASHER, LOCK 1/4” 4
50 140000 WASHER, FLAT 1/4” 3
51 601292 COVER PLATE, TANK 1
52 601295 SCREW, ”U” BOLT, 1/4--20X1.50ID 1
53 601282 PLATE, SPACER 1
54 601365 DVALVE BALL, 3/4” MPT X 3/4” FPT 1
55 140226 SCREW, 5/16--18X5/8 4
56 140015 WASHER, SPLIT LOCK 5/16 4
57 103065 DCASTER, SWIVEL 4” 1
58 608348 TANK, 16 GAL, GREEN 1
59 1035609 DECAL, “MONSOON” 2
60 601297 BRACKET, VALVE 1
61 140011 WASHER 4
62 41169 NUT, HEX, LOCK, .25--20, NL, SS 2
63 1034636 DECAL, NOBLES LOGO 1

PARTS LIST
8Monsoont(08--07)
DISPENSER ASSEMBLY
15
14
13
26
25
27
12
12
16
17
1
2
3
41
6
5
9810
78
11
18
19
20
2122
23
21
1
28
28
29
29
29
24
REF PART # DESCRIPTION QTY.
∇607703 ASM., 30” DISPENSER W/ BRUSH 1
Y1630258 PIN, CLEVIS 3
Y2230454 BRACKET, SQUEEGEE MOUNT 1
Y3140017 WASHER, SPLIT LOCK 3/8” 2
Y402994 SCREW, HEX, .38--16X0.75, SS 2
Y5102560 PAD, NON--SLIP 1
Y6230456 PEDAL, LIFT 1
Y759156 NUT, HEX, LOCK, .38--16, NL 1
Y8140028 WASHER, FLAT 3/8” 2
Y9140925 SPACER, CHASSIS 3/16” 1
Y10 611048 SCREW, HEX, .38--16X1.25, SS 1
Y11 601286 BRACKET, DISPENSER LIFT 1
Y12 1011094 DKNOB 2
Y13 630018 HOSE, 1.00D 0.75B 33.0L 1
Y14 612146000 FITTING, STR .75” HOSE, .75” NPT 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEM
REF PART # DESCRIPTION QTY.
Y15 601364 FITTING, 90_ELBOW 3/4” 1
Y16 601360 CONNECTOR 1
Y17 601361 O--RING 1
Y18 601303 DBRUSH, STRIP 10” 3
Y19 140798 SCREW, 6X7/8 9
Y20 601298 BRACKET, 30” DISPENSER ASM 1
Y21 601363 PLUG, TAPPERED 2
Y22 601362 DISPENSER, DRIP BAR ASM 30” 1
Y23 573073 CLIP, WAND 1” TO 1--1/2” DIA 1
Y24 140197 SCREW,10--24X3/8 1
Y25 1014918AM DWHEEL, 3.0D 0.88W 0.31B W/BSHG 2
Y26 140027 WASHER, FLAT 5/16” 2
Y27 28819 NUT, LOCK 5/16--18 2
Y28 140799 SCREW 2
Y29 612254000 PIN, HAIRPIN 3