Nokia 3155 Service manual

Nokia Customer Care
3155/3155i (RM-41), 3152 (RM-61)
Mobile Terminal
ISSUE 1 07/2005 Company Confidential ©2005 Nokia Corporation
Service Tools

3155/3155i (RM-41), 3152 (RM-61)
Service Tools
Page 2 ©2005 Nokia Corporation Company Confidential ISSUE 1 07/2005
Contents Page
Service Tools..................................................................................................................................................... 3
ACF-8 ..............................................................................................................................................................3
CA-51DS Flash Cable ..................................................................................................................................3
CA-25RS RF Test Cable ..............................................................................................................................3
CA-56RS RF Test Cable ..............................................................................................................................4
CA-52PS DC Service Cable ........................................................................................................................4
DA-47 Docking Station Adapter .............................................................................................................4
DAU-9S FBUS/MBUS Cable ......................................................................................................................5
DKU-2 Flash Cable ......................................................................................................................................5
FLC-20 Flashing Device ..............................................................................................................................5
FLS-4S Flashing Device ..............................................................................................................................6
FPS-8 Flash Prommer .................................................................................................................................6
FPS-10 Flash Prommer ...............................................................................................................................6
JXS-2 Shield Box .........................................................................................................................................6
JBV-1 Docking Station ...............................................................................................................................7
MJ-57 Module Jig .......................................................................................................................................7
PCS-1 Power Cable .....................................................................................................................................7
PKD-1 Software Security Dongle ............................................................................................................8
RJ-18 Power Amp LGA Rework Jig and ST-16 PA Stencil ...............................................................8
RJ-61 Soldering Jig .....................................................................................................................................9
RJ-64 LNA LGA Rework Jig and ST-24 Stencil ....................................................................................9
RJ-65 TX IC LGA Rework Jig and ST-25 Stencil ................................................................................10
RJ-100 Rework Jig and ST-34 Stencil .................................................................................................10
SA-51 GPS Antenna Coupler ..................................................................................................................11
SA-54 RF Calibration Adapter ...............................................................................................................11
SRT-6 Opening Tool ..................................................................................................................................11
SS-13 Tuning Docking Station ..............................................................................................................12
SS-50 Domesheet Alignment Jig ..........................................................................................................12
SS-64 Opening Tool ..................................................................................................................................12
SS-79 Flip Module Rest for RF coupler ...............................................................................................13
SX-4 Smart Card ........................................................................................................................................13
XCS-4 MBUS/FBUS Cable ........................................................................................................................13
XRS-6 RF Cable ..........................................................................................................................................14
Service Configurations............................................................................................................................... 15
Service Setup1: POS Flashing ................................................................................................................15
Service Setup 2: Flashing with Docking Station ..............................................................................16
Service Setup 3: Testing with Module Jig ..........................................................................................17
Service Setup 4: EM Calibration ...........................................................................................................18
Service Configuration 5: Automated Tuning and Alignment ........................................................19
Service Configuration 6: GPS Engine Testing ....................................................................................20
GPS Engine Test Setup ......................................................................................................................... 20
GPS Antenna Test Setup ...................................................................................................................... 21

Nokia Customer Care Service Tools
3155/3155i (RM-41), 3152 (RM-61)
ISSUE 1 07/2005 ©2005 Nokia Corporation Company Confidential Page 3
Service Tools
ACF-8
The ACF-8 is a universal power supply for FLS-4S and FPS-8.
CA-51DS Flash Cable
The CA-51DS allows bottom connector flashing using the FLS-4S Flash Device or the
FLC-20 Flash Device.
CA-25RS RF Test Cable
The CA-25RS test cable is used for RF engine testing and tuning. This cable is 30 cm long.
It snaps directly on the mobile terminal’s RF connector and converts the output to an
surface mounting assembly connector. Removal of the E-cover is required for CDMA RF
testing. This cable is also used for GPS engine testing, but removal of the A-cover is
required.

3155/3155i (RM-41), 3152 (RM-61)
Service Tools
Page 4 ©2005 Nokia Corporation Company Confidential ISSUE 1 07/2005
CA-56RS RF Test Cable
The CA-56RS test cable is used with Module Jig (MJ-57) for RF engine testing and
tuning. This cable is 10 cm long. It snaps directly on the mobile terminal’s RF connector
and converts the output to an surface mounting assembly connector.
CA-52PS DC Service Cable
The CA-52 is used together with JBV-1 Docking Station and DA-47 Docking Station
Adapter for EM calibrations. This cable is for a smaller Dynamo DC-jack.
DA-47 Docking Station Adapter
The DA-47 works in conjunction with the JBV-1 Docking Station and the FPS-8, FPS-10
Prommer Boxes to allow calibration, tuning, and software flashing of the mobile
terminal. It supports the LYNX battery interface, which does not require BTEMP. The DA-
47 also has a built-in RUIM card reader.

Nokia Customer Care Service Tools
3155/3155i (RM-41), 3152 (RM-61)
ISSUE 1 07/2005 ©2005 Nokia Corporation Company Confidential Page 5
DAU-9S FBUS/MBUS Cable
The DAU-9S is a general purpose cable that supports FBUS/MBUS communication
between a Mod-10 device and a PC.
DKU-2 Flash Cable
The DKU-2 is used for USB flashing. Use this flash cable with the FLC-20 Flashing Device
or with the FLS-4S Flashing Device.
FLC-20 Flashing Device
The FLC-20 allows point-of-sale (POS) locations to flash the handset. This device allows
bottom Pop-portTM connector flashing.
Note: Requires either the CA-51DS Service Cable or DKU-2 Flash Cable (not
included).
Note: The FLC-20 is not supported in the APAC, LTA and China markets.

3155/3155i (RM-41), 3152 (RM-61)
Service Tools
Page 6 ©2005 Nokia Corporation Company Confidential ISSUE 1 07/2005
FLS-4S Flashing Device
The FLS-4S allows point-of-sale (POS) locations to flash the mobile terminal.
FPS-8 Flash Prommer
The FPS-8 is used for mobile terminal flashing at authorized service centers.
FPS-10 Flash Prommer
The FPS-10 replaces the FPS-8 Flash Prommer. The FPS-10 allows the flash code to be
pre-loaded into the unit's memory and then can be flashed directly to the mobile
terminal at high speeds. A smart card is required when flashing DCT-4 mobile terminal.
JXS-2 Shield Box
The JXS-2 is used to perform RF radiated testing and antenna testing.

Nokia Customer Care Service Tools
3155/3155i (RM-41), 3152 (RM-61)
ISSUE 1 07/2005 ©2005 Nokia Corporation Company Confidential Page 7
JBV-1 Docking Station
The JBV-1 connects flash prommers. The docking station can be powered by the FPS-8
Flash Prommer or by an external power supply.
MJ-57 Module Jig
The MJ-57 is used as a means to secure the PWBs and displays for troubleshooting with
the covers off. The design provides DC power input and a communication port for the
service software. In addition, the MJ-57 provides a secure way of connecting RF cables
for testing and tuning. The CA-56RS cable is required for RF testing.
Note: The MJ-57 Module Jig’s flex PWB is sold as a separate spare part.
Note: The CA-56RS cable is not included in the MJ-57 sales package. When the cable
is attached to the MJ-57 jig and the PWB is inserted, make sure to press the PWB
into place to ensure good contact with the cable.
PCS-1 Power Cable
The PCS-1 is used to connect the service tools (e.g., JBV-1 Docking Station, MJ-57
Service Jig) to an external power supply.

3155/3155i (RM-41), 3152 (RM-61)
Service Tools
Page 8 ©2005 Nokia Corporation Company Confidential ISSUE 1 07/2005
PKD-1 Software Security Dongle
The PKD-1 is a hardware dongle that, when connected to the parallel (LPT) port of the
PC, enables the use of the service software. It is not possible to use the service software
without the dongle. Printers or other peripheral devices can be connected to the PC
through the dongle, if needed.
Caution: Make sure that you have switched off the PC and the printer before making
connections.
Caution: Do not connect the PKD-1 to the serial port. You may damage your PKD-1
and/or your PC.
RJ-18 Power Amp LGA Rework Jig and ST-16 PA Stencil
The ST-16 stencil allows rework on LGA-type components that do not have pre-tinned
pads. Both power amps require the use of this stencil. The stencil is designed to
specifically fit the PA pad configuration and dimensions. The RJ-18 fits the physical
dimension of the PAs.
Note: Used in conjunction with the SPS-1 Paste Spreader.

Nokia Customer Care Service Tools
3155/3155i (RM-41), 3152 (RM-61)
ISSUE 1 07/2005 ©2005 Nokia Corporation Company Confidential Page 9
RJ-61 Soldering Jig
The RJ-61 serves as a mechanical holder for desoldering and soldering of components. It
provides a convenient means to replace components on the PWB when they are changed
during service repairs at authorized AMS locations. The RJ-61 allows soldering of the
engine PWB as well as the UI-PWB.
RJ-64 LNA LGA Rework Jig and ST-24 Stencil
The ST-24 stencil allows rework on LGA-type components that do not have pre-tinned
pads. The LNA requires the use of this stencil. The stencil is designed to specifically fit
the pad configuration and dimensions while the rework jig fits the physical dimension of
the LNA.
Note: Used in conjunction with the SPS-1 Paste Spreader.

3155/3155i (RM-41), 3152 (RM-61)
Service Tools
Page 10 ©2005 Nokia Corporation Company Confidential ISSUE 1 07/2005
RJ-65 TX IC LGA Rework Jig and ST-25 Stencil
The ST-25 stencil allows rework on LGA-type components that do not have pre-tinned
pads. The Tx RF IC requires the use of this stencil. The stencil is designed to specifically fit
the IC pad configuration and dimensions while the rework jig fits the physical dimension
of the IC.
Note: Used in conjunction with the SPS-1 Paste Spreader.
RJ-100 Rework Jig and ST-34 Stencil
The ST-34 stencil allows rework on LGA-type components that do not have pre-tinned
pads. The stencil is designed to specifically fit the N7200 pad configuration and
dimensions. The RJ-100 fits the physical dimension of the N7200.
Note: Used in conjunction with the SPS-1 Paste Spreader.