Nora NSPEC Marquise II Series User manual

6505 Gayhart St., Commerce, CA 90040 | Phone: [phone] | FAX: [phone] www.noralighting.com | e-mail: [email protected]
Specifications subject to change without notice. © 2016
®
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED
OUT BY YOUR LOCAL ELECTRICIAN.
Installation Instructions
NRMC2 Series Marquise II Retrofit
***IMPORTANT: READ PRIOR TO ATTEMPTING INSTALLATION***
WARNING: Fire/Electrical Hazard
This equipment is intended to be installed only by qualified personnel. The installation must be made in accordance with the
current edition to the National Electric Code and all applicable state and local building codes. The final installation must be
approved by the appropriate qualified electrical/building inspector(s). Improper installation may result in a fire or electrical hazard.
Be sure the electrical power to the circuit has been disconnected before installing this electrical system.
AVERTISSEMENT : Fire / Risque électrique
Cet équipement est destiné à être installé uniquement par du personnel qualifié . L’installation doit être faite en conformité avec
l’édition actuelle du Code national de l’électricité et toutes étatiques et locales codes du bâtiment applicables . L’installation finale
doit être approuvée par l’ inspecteur en électricité / bâtiment qualifié approprié ( s) . Une mauvaise installation peut entraîner
un incendie ou un risque électrique . Soyez sûr de la puissance électrique vers le circuit a été coupée avant l’installation de ce
système électrique .
Fig. 1 Marquise II Trim
Fig. 3
Fig. 2 Retrofit Kit
a. Medium-base socket adapter
b. Male Ideal®Connector
c. LED Lamp Replacement Marking Sticker
A. B.
C.
B. HOUSING DIMENSIONS
A. PACKAGING CONTENTS
4” 5” 6”
Min.Height 5-1/2” 5-1/2” 5-1/2”
Width 4-1/8” 5-3/8” 6-1/8”
C. ELECTRICAL RATINGS
Refer to correlation label of luminaire and/or specication
sheet in Nora’s website. www.noralighting.com
Safety tests was conducted in minimum housing
dimension specied above (Fig. 3). Luminaire
malfunction and overheating may occur if installed
into a smaller housing.

6505 Gayhart St., Commerce, CA 90040 | Phone: [phone] | FAX: [phone] www.noralighting.com | e-mail: [email protected]
Specifications subject to change without notice. © 2016
®
FOR LED/DEDICATED HOUSINGS:
1. Connect orange female to male connecter and ground wire of the xture to housing (Fig.4).
Connector is not intended to support weight of the xture. Please support xture at all times.
2. Squeeze in mounting blade on both side and carefully push xture into the housing (Fig.5)
3. Aim xture straight down r angle towards a focal point.
Medium Based Housing:
1. Place provided LED Lamp Replacement Marking Sticker inside the
housing where visible to installer.
2. Remove medium-base mounting bracket only if necessary to provide
room for xture to be installed fully and properly into the housing. (g. 7)
3. Use provided Medium-base socket adapter and attach each end to
housing and xture. (g.8)
4. Aim xture straight down r angle towards a focal point.
Only those open holes indicated in the photographs and/or drawings may
be made or altered as a result of kit installation.
Do not leave any other open holes in
an enclosure of wiring or
electrical components.
Remove bracket
if necessary.
FIGURE 4
FIGURE 7 FIGURE 8
FIGURE 5
Male Connector
Male Connector Male Connector
Female Connector
Ground Wire Ground Wire
Converting Medium Based Housing to Dedicated:
1. Place provided LED Lamp Replacement Marking Sticker
inside the housing where visible to installer.
2. Cut Medium-base socket adapter (Figure A)
3. Replace with provided male orange connector (Figure B)
4. Connect ground & xture to housing (Figure C)
5. Squeeze in mounting blade on both side and carefully push
xture into the housing (Fig.5)
6. Aim xture straight down r angle towards a focal point.
FIGURE A FIGURE B
FIGURE C