Norbord CSS 793 User manual

Panels Hardware Tools required
C
15mm
25mm
8 x
8 x
2 x
8 x
10 x
40mm
D
30mm
4 x
4 x
A
8 x
H
B
R
G
E
1000mm WIDE
Cabinet
WALL
G
A
1
GA
G
A
GA
A
G
1
L
G
Apply a small
droplet of glue
to hole before
inserting
Cross Head Screwdriver
Note: If you
are using
a colour
matched
end panel, use
this to replace
the identically
sized side
panel supplied
within this
pack.
Inside groove
to back
Left side panel
Right side panel
H
H
H
H
H
2
3
H
H
H
Insert as shown. It's IMPORTANT
that arrow points to outside edge.
2
H
H
Drill & Drill Bits
PVA Wood Glue
Pliers x 2
Hammer
Spirit Level
To construct
cabinets & legs
3mm
To fit
handles
4.5mm
CSS793 0?/10
DD
LL
AG
Insert and as shown, repeat for opposite side panel.
Attach wall hanging units using the pre-marked holes as
shown using screws . Please note the back of the hanging
bracket does not line up with the back panel groove.
L
D
4 x
I
4 x
N
4 x
M
2 x L
2 x
K
Before you start . . .
WARNING: Installation should be performed by a competent person only. This
product could be dangerous if incorrectly installed. Check the pack and make sure all
the components are included - if not, call the Manufacturers' Helpline on 01769 575500
and their team will get things sorted. When you are ready to start make sure you have the
right tools to hand, plenty of space and a clean dry area for building. Don't rush, read the
instructions first and run through the sequence before you begin. Assembly should be done
in the stages shown in the following diagrams, constructing one unit at a time and keeping
fittings together to avoid loss. Lay large panels on the floor using the packaging for
protection. Do not over tighten screws.
Cleaning - Use mild soap and water only. Do not use abrasive cleaners.
Wall Fixings Hinges
(standard
doors only)

Now affix to wall
To fit shelves
E
Push shelf support into
chosen shelf position holes,
5 supports per shelf. Tilt and
slide in shelf.
Joining and Levelling
of Cabinets
3
3
R
3mm
90°
4
6
5
H
3
1
2
5
Slide back
panel into groove.
3
1
2
Connect base
panel
onto side
panel as
shown.
Repeat for top
panel
3
1
2
1
3
4
C
C
Fit central
support post
and
secure with
4 x screws.
C
4
H
2
1
3
H
1
Connect side panel as shown
tighten clockwise in remaining 4 positions.
1
2
1
3
5
H
H
Tighten clockwise
in 4 positions.
H
H
H
Run small
bead of glue
along all
grooves
To fit door handles
Position your choice of handle (available separately) using the drilling guide
available in stores.
Mark 20mm on a 3mm dia. drill bit with
masking tape. Drill between the 2 holes
drilled for the hinges, through one cabinet
side (16mm) and 4mm into the next,
stopping when you reach the marker.
Join the cabinets together with
2 x screws.
R
CSS793 0?/10
Fixing to Wall
Adjustment – IN & OUT to Wall
Adjustment – UP & DOWN to Wall
Spacing between side panels –
allow 18mm clearance each side
Measure
57mm from
top of unit
Position and secure fitting brackets to the wall with suitable fixings.
WARNING: This unit could be dangerous if fitted incorrectly to the
wall.(Fixings are not supplied with the pack as they vary according to the
type of walls you have. If you are unsure, ask an expert).
Hang cabinet onto
wall brackets
and adjust to level
as shown.
Ensure that front
face of unit is
vertical by using
spirit level.
K
K
K
K
K
K
K
K
Insert door hinge into
recess in door and affix
using 2x screws.
Turn screw as shown, to adjust the door position
B
N
Connect door hinge to cabinet
and tighten screw shown.
Affix hinge plate to cabinet using
pre-drilled holes with
pre-mounted screws.
After adjustment is complete
apply cover plate
IM
l
e
n
a
p
foe
g
d
E
Door hinges (standard doors only)
If you have chosen framed doors, refer to the instructions supplied in the
separate hinge pack for the frame fixing, fitting and adjustment of hinges.
Now affix to wall
To fit shelves
E
Push shelf support into chosen shelf position holes, 5 supports per shelf. Tilt and slide in shelf.
Joining and Levelling
of Cabinets
3
3
R
3mm
90°
4
6
5
H
3
1
2
5
Slide back panel into groove.
3
1
2
Connect base
panel
onto side
panel as
shown.
Repeat for top
panel
3
1
2
1
3
4
C
C
Fit central support post
and
secure with 4 x screws.
C
4
H
2
1
3
H
1
Connect side panel as shown tighten clockwise in remaining 4 positions.
1
2
1
3
5
H
H
Tighten clockwise in 4 positions.
H
H
H
Run small bead of glue along all grooves
To fit door handles
Position your choice of handle (available separately) using the drilling guide available in stores.
Mark 20mm on a 3mm dia. drill bit with
masking tape. Drill between the 2 holes
drilled for the hinges, through one cabinet
side (16mm) and 4mm into the next,
stopping when you reach the marker. Join the cabinets together with
2 x screws.
R
CSS793 0?/10
Fixing to Wall
Adjustment – IN & OUT to Wall
Adjustment – UP & DOWN to Wall
Spacing between side panels –
allow 18mm clearance each side
Measure
57mm from
top of unit
Position and secure fitting brackets to the wall with suitable fixings. WARNING: This unit could be dangerous if fitted incorrectly to the wall.(Fixings are not supplied with the pack as they vary according to the type of walls you have. If you are unsure, ask an expert).
Hang cabinet onto wall brackets and adjust to level as shown. Ensure that front face of unit is vertical by using spirit level.
K
K
K
K
K
K
K
K
Insert door hinge into recess in door and affix using 2x screws.
Turn screw as shown, to adjust the door position
B
N
Connect door hinge to cabinet and tighten screw shown.
Affix hinge plate to cabinet using
pre-drilled holes with pre-mounted screws.
After adjustment is complete apply cover plate
IM
l
e
n
a
p
foe
g
d
E
Door hinges (standard doors only)
If you have chosen framed doors, refer to the instructions supplied in the separate hinge pack for the frame fixing, fitting and adjustment of hinges.