Norbord CSS806 User manual

Push shelf support into
chosen shelf position holes,
4 per shelf. Tilt and
slide in shelf.
Insert as shown. It's IMPORTANT
that arrow points to outside edge.
2 x Side Panels
2 x Top Rails
1 x Base Panel
1 x Back Panel
1 x Adjustable Shelf
1
2
3
4
5
Panels Hardware Tools required
1
Note: If you are using a colour
matched end panel, use this to
replace the identically sized side
panel supplied within this pack.
Insert and as shown, repeat
for opposite side panel.
Inside groove to back
Left side panel Right side panel
AG
15mm
25mm
8 x
8 x
22 x
2 x
12 x
2 x
A
H
B
R
G
F
4 x E
Cross Head Screwdriver
Now affix your cabinet legs
To fit shelves
Joining and Levelling
of Cabinets
Fitting to wall
Drill 3mm pilot hole.
Fix bracket
with screw.
B
F
Use appropriate fittings to secure
cabinet to wall (depending on
wall type).
All legs are pre-set
at 150mm height.
Rotate to adjust up
and down, to level the
unit.
3
3
3mm
90
F
R
Mark 20mm on a 3mm
dia. drill bit with
masking tape. Drill
between the 2 holes
drilled for the hinges,
through one cabinet
side (16mm) and
4mm into the next,
stopping when you reach
the marker. Join the
cabinets together with
2 x screws.
R
E
Drill & Drill Bits
PVA Wood Glue
Pliers x 2
Hammer
Spirit Level
To construct
cabinets & legs
3mm
To fit
handles
4.5mm
G
A
GA
AG
GA
AG
G
Apply a small
droplet of glue
to hole before
inserting
1
G
NO central wood dowel
required to top of cabinet
side panels.
400mm WIDE
BASE
Cabinet
2
1
3
4
5
H
H
H
H
H
H
H
H
H
2
2
2
3
H
Connect base
panel
onto side
panel as
shown.
Repeat for top
rails .
3
H
3
1
2
2
3
1
2
Connect side panel as shown
tighten clockwise in 8 positions.
H
H
41
2
2
1
3
1
Slide back
panel into groove.
Carefully drill through panel
into the edge of panel and
secure using 2 x screws.
5
3
Run small
bead of glue
along all
grooves
1
2
4
3
4
4
2
B
B
3mm
ASSEMBLY GUIDE
CSS806 07/12
CSS806 07/12
Insert door hinge into
recess in door and affix
using 2x screws.
Turn screw as shown, to adjust the door position
B
N
Connect door hinge to cabinet
and tighten screw shown.
Affix hinge plate to cabinet using
pre-drilled holes with
pre-mounted screws.
After adjustment is complete
apply cover plate
IM
Edge of panel
Legs
Hinges
2 x I
2 x N
2 x M
Please note at this point
if you are building a
drawer line unit it is
advisable to fit
the drawer runners
at this stage.
If fitting the standard
drawer boxes please use
the pre marked positions
on the cabinet.
If you have chosen
upgraded drawer boxes
or framed doors, refer to
the instructions supplied
with the drawer box.
Door hinges (standard doors only)
If you have chosen framed doors, refer to the instructions supplied in the
separate hinge pack for frame fixing, fitting and adjustment of hinges.
Before you start . . .
WARNING: Installation should be performed by a competent person only. This product could be dangerous if incorrectly
installed.
Check the pack and make sure all the components are included - if not, call the Manufacturers' Helpline on 01769
575500 and their team will get things sorted. When you are ready to start make sure you have the right tools to hand, plenty of
space and a clean dry area for building. Don't rush, read the instructions first and run through the sequence before you begin.
Assembly should be done in the stages shown in the following diagrams, constructing one unit at a time and keeping fittings
together to avoid loss. Lay large panels on the floor using the packaging for protection. Do not over tighten screws.
Cleaning - Use mild soap and water only. Do not use abrasive cleaners.
Video assembly guides can be viewed at www.mycabinetguide.co.uk
(standard doors only)
4 x O4 x Q2 x P
2 x S

Push shelf support into
chosen shelf position holes,
4 per shelf. Tilt and
slide in shelf.
Insert as shown. It's IMPORTANT
that arrow points to outside edge.
2 x Side Panels
2 x Top Rails
1 x Base Panel
1 x Back Panel
1 x Adjustable Shelf
1
2
3
4
5
Panels Hardware Tools required
1
Note: If you are using a colour
matched end panel, use this to
replace the identically sized side
panel supplied within this pack.
Insert and as shown, repeat
for opposite side panel.
Inside groove to back
Left side panel Right side panel
AG
15mm
25mm
8 x
8 x
22 x
2 x
12 x
2 x
A
H
B
R
G
F
4 x E
Cross Head Screwdriver
Now affix your cabinet legs
To fit shelves
Joining and Levelling
of Cabinets
Fitting to wall
Drill 3mm pilot hole.
Fix bracket
with screw.
B
F
Use appropriate fittings to secure
cabinet to wall (depending on
wall type).
All legs are pre-set
at 150mm height.
Rotate to adjust up
and down, to level the
unit.
3
3
3mm
90
F
R
Mark 20mm on a 3mm
dia. drill bit with
masking tape. Drill
between the 2 holes
drilled for the hinges,
through one cabinet
side (16mm) and
4mm into the next,
stopping when you reach
the marker. Join the
cabinets together with
2 x screws.
R
E
Drill & Drill Bits
PVA Wood Glue
Pliers x 2
Hammer
Spirit Level
To construct
cabinets & legs
3mm
To fit
handles
4.5mm
G
A
GA
AG
GA
AG
G
Apply a small
droplet of glue
to hole before
inserting
1
G
NO central wood dowel
required to top of cabinet
side panels.
400mm WIDE
BASE
Cabinet
2
1
3
4
5
H
H
H
H
H
H
H
H
H
2
2
2
3
H
Connect base
panel
onto side
panel as
shown.
Repeat for top
rails .
3
H
3
1
2
2
3
1
2
Connect side panel as shown
tighten clockwise in 8 positions.
H
H
41
2
2
1
3
1
Slide back
panel into groove.
Carefully drill through panel
into the edge of panel and
secure using 2 x screws.
5
3
Run small
bead of glue
along all
grooves
1
2
4
3
4
4
2
B
B
3mm
ASSEMBLY GUIDE
CSS806 07/12
CSS806 07/12
Insert door hinge into
recess in door and affix
using 2x screws.
Turn screw as shown, to adjust the door position
B
N
Connect door hinge to cabinet
and tighten screw shown.
Affix hinge plate to cabinet using
pre-drilled holes with
pre-mounted screws.
After adjustment is complete
apply cover plate
IM
Edge of panel
Legs
Hinges
2 x I
2 x N
2 x M
Please note at this point
if you are building a
drawer line unit it is
advisable to fit
the drawer runners
at this stage.
If fitting the standard
drawer boxes please use
the pre marked positions
on the cabinet.
If you have chosen
upgraded drawer boxes
or framed doors, refer to
the instructions supplied
with the drawer box.
Door hinges (standard doors only)
If you have chosen framed doors, refer to the instructions supplied in the
separate hinge pack for frame fixing, fitting and adjustment of hinges.
Before you start . . .
WARNING: Installation should be performed by a competent person only. This product could be dangerous if incorrectly
installed.
Check the pack and make sure all the components are included - if not, call the Manufacturers' Helpline on 01769
575500 and their team will get things sorted. When you are ready to start make sure you have the right tools to hand, plenty of
space and a clean dry area for building. Don't rush, read the instructions first and run through the sequence before you begin.
Assembly should be done in the stages shown in the following diagrams, constructing one unit at a time and keeping fittings
together to avoid loss. Lay large panels on the floor using the packaging for protection. Do not over tighten screws.
Cleaning - Use mild soap and water only. Do not use abrasive cleaners.
Video assembly guides can be viewed at www.mycabinetguide.co.uk
To fit door handles
Position your choice
of handle (available
separately) using the
drilling guide available
in stores.
To fit plinths
Lay plinth panel in front of cabinet.
Position plinth clip plate opposite
front cabinet legs. Secure with 2 x
screws .
Slide into . Stand plinth up.
S
S Q
S
P
B
o
Cabinet
Underside
Position as shown,
lip on underside of
side panel.
Ensure screw hole
is not over panel join.
Tap in the central
plastic lug
Drill pilot holes
3mm x 3 positions
Secure with screw
x 3 positions.
Then push leg into leg boss
O
Rotate to adjust
height
3
B
B