Norbord CSS 805 User manual

Notes
CSS805 07/12 CSS805 07/12
Joining and Levelling
of Cabinets
Fitting to wall
Drill 3mm pilot hole.
Fix bracket
with screw.
B
F
All legs are pre-set
at 150mm height.
Rotate to adjust up
and down, to level the
unit.
3
3
3mm
Mark 20mm on a 3mm
dia. drill bit with
masking tape. Drill
between the 2 holes
drilled for the hinges,
through one cabinet
side (16mm) and
4mm into the next,
stopping when you reach
the marker. Join the
cabinets together with
2 x screws.
90
R
F
R
Panels Hardware Tools required
150mm WIDE (Pull Out)
BASE
Cabinet
ASSEMBLY GUIDE
Cross Head Screwdriver
15mm
25mm
8 x
8 x
10 x
2 x
12 x
2 x
Pull Out
Wire System
(Boxed)
1 x
A
H
B
R
G
F
2 x Side Panels
1 x Top Panel
1 x Base Panel
1 x Back Panel
1
2
3
4
1
2
3
4
Legs
Drill & Drill Bits
PVA Wood Glue
Pliers x 2
Hammer
Spirit Level
To construct
cabinets & legs
3mm
To fit
handles
4.5mm
1
AG
Insert and as shown, repeat
for opposite side panel.
2
H
3
H
H
H
H
H
H
H
H
H
H
Insert as shown. It's IMPORTANT
that arrow points to outside edge.
2
GAG
AG
GA
G
AG
1
G
A
G
Apply a small
droplet of glue
to hole before
inserting
4
H
H
1
2
4
H
Tighten clockwise
in 4 positions.
4
Slide back
panel into groove.
Run small
bead of glue
along all
grooves
3
3
1
2
H
1
2
Connect base panel
onto side panel as
shown. Repeat for
top panel
5
1
2
H
H
1
2
Connect side panel as shown,
tighten clockwise in 4 positions.
1
NOTE: The pull-out wire system
can be fitted to either side panel,
and is shown here fitted to the
RH side. For fitting instructions,
please refer to the assembly
guide supplied with the pull-out
wire system.
Now affix your cabinet legs
Use appropriate
fittings to secure
cabinet to wall
(depending on
wall type).
3
33
3
4
1
Before you start . . .
WARNING: Installation should be performed by a competent person only. This product could be dangerous if incorrectly
installed.
Check the pack and make sure all the components are included - if not, call the Manufacturers' Helpline on 01769
575500 and their team will get things sorted. When you are ready to start make sure you have the right tools to hand, plenty of
space and a clean dry area for building. Don't rush, read the instructions first and run through the sequence before you begin.
Assembly should be done in the stages shown in the following diagrams, constructing one unit at a time and keeping fittings
together to avoid loss. Lay large panels on the floor using the packaging for protection. Do not over tighten screws.
Cleaning - Use mild soap and water only. Do not use abrasive cleaners.
Video assembly guides can be viewed at www.mycabinetguide.co.uk
2 x O2 x Q1 x P
1 x S

Notes
CSS805 07/12
CSS805 07/12
Joining and Levelling
of Cabinets
Fitting to wall
Drill 3mm pilot hole.
Fix bracket
with screw.
B
F
All legs are pre-set
at 150mm height.
Rotate to adjust up
and down, to level the
unit.
3
3
3mm
Mark 20mm on a 3mm
dia. drill bit with
masking tape. Drill
between the 2 holes
drilled for the hinges,
through one cabinet
side (16mm) and
4mm into the next,
stopping when you reach
the marker. Join the
cabinets together with
2 x screws.
90
R
F
R
Panels Hardware Tools required
150mm WIDE (Pull Out)
BASE
Cabinet
ASSEMBLY GUIDE
Cross Head Screwdriver
15mm
25mm
8 x
8 x
10 x
2 x
12 x
2 x
Pull Out
Wire System
(Boxed)
1 x
A
H
B
R
G
F
2 x Side Panels
1 x Top Panel
1 x Base Panel
1 x Back Panel
1
2
3
4
1
2
3
4
Legs
Drill & Drill Bits
PVA Wood Glue
Pliers x 2
Hammer
Spirit Level
To construct
cabinets & legs
3mm
To fit
handles
4.5mm
1
AG
Insert and as shown, repeat
for opposite side panel.
2
H
3
H
H
H
H
H
H
H
H
H
H
Insert as shown. It's IMPORTANT
that arrow points to outside edge.
2
GAG
AG
GA
G
AG
1
G
A
G
Apply a small
droplet of glue
to hole before
inserting
4
H
H
1
2
4
H
Tighten clockwise
in 4 positions.
4
Slide back
panel into groove.
Run small
bead of glue
along all
grooves
3
3
1
2
H
1
2
Connect base panel
onto side panel as
shown. Repeat for
top panel
5
1
2
H
H
1
2
Connect side panel as shown,
tighten clockwise in 4 positions.
1
NOTE: The pull-out wire system
can be fitted to either side panel,
and is shown here fitted to the
RH side. For fitting instructions,
please refer to the assembly
guide supplied with the pull-out
wire system.
Now affix your cabinet legs
Use appropriate
fittings to secure
cabinet to wall
(depending on
wall type).
3
3
3
3
4
1
Before you start . . .
WARNING: Installation should be performed by a competent person only. This product could be dangerous if incorrectly
installed.
Check the pack and make sure all the components are included - if not, call the Manufacturers' Helpline on 01769
575500 and their team will get things sorted. When you are ready to start make sure you have the right tools to hand, plenty of
space and a clean dry area for building. Don't rush, read the instructions first and run through the sequence before you begin.
Assembly should be done in the stages shown in the following diagrams, constructing one unit at a time and keeping fittings
together to avoid loss. Lay large panels on the floor using the packaging for protection. Do not over tighten screws.
Cleaning - Use mild soap and water only. Do not use abrasive cleaners.
Video assembly guides can be viewed at www.mycabinetguide.co.uk
To fit door handles
Position your choice
of handle (available
separately) using the
drilling guide available
in stores.
To fit plinths
Lay plinth panel in front of cabinet.
Position plinth clip plate opposite
front cabinet legs. Secure with 2 x
screws .
Slide into . Stand plinth up.
S
S Q
S
P
B
o
Cabinet Underside
Position as shown,
lip on underside of
side panel.
Ensure screw hole
is not over panel join.
Tap in the central
plastic lug
Drill pilot holes
3mm x 3 positions
Secure with screw
x 3 positions.
Then push leg into
leg boss
O
Rotate to adjust
height
3
B
B