NordicTrack T 7.0 Treadmill User manual

#10 x 3/4" Screw
(4)–4
#8 x 1/2" Ground
Screw (6)–1
3/8" Star
Washer (10)–6
3/8" Nut (9)–4
#8 x 3/4" Screw
(6)–12
Wa
#10 Star
sher (5)–4
3/8" x 2" Bolt (2)–2 3/8" x 2 1/2" Bolt (7)–2
3/8" x 3 1/2" Screw (9)–4
3/8" x 4" Screw (3)–6
5/16" x 1"
Screw (7)–2
#8 x 1/2" Screw
(1)–14
5/16" x 2 3/4" Screw (12)–4
5/16" Flat
Washer (XX)–4
5/16" Star
Washer (8)–4
#8 x 3/4" Tek
Screw (13)–8
For detailed instructions, see the User’s Manual. Note: The underside of the walking belt is coated with high-
performance lubricant. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth
and a mild, non-abrasive cleaner.
NORDICTRACK® T7.0 Treadmill • Model No. 831.24977 • Revised 08/19/11
QUICK ASSEMBLY GUIDE

3. Route the Upright Wire (91) through the Left
Upright (84).
4. Attach the Left Upright (84). Then, repeat steps
2 and 4 on the right side.
2
84
84
Wire
Tie
91
Wire
Tie
91
84
3
10
Wires
1. Pull the Upright Wire (91) and the Base Ground
Wire (86) through the hole. Remove and discard
the Screw (A). Attach the Base Ground Wire.
Hole
6
A
86
90
Cut
91
Tie
91
2. Attach a Wheel (93). Attach a Thick Base Pad
(37) and a Thin Base Pad (92). Press the Base
Cap (87) in.
7
93
13
13
37
87
92
9

7. Remove and discard the Screws (A), and then
remove the Pulse Crossbar (81). Remove the
four 5/16" x 5/8" Screws (11).
8. Attach the Trays (95, 96).
3
81
11
11
A
96
95
1
1
1
1
1
6. Route the Upright Wire (91) through the Left
Handrail (79). Attach the Left Handrail. Remove
and discard the Screws (C). Repeat this step
on the right side.
5. Slide the Base Covers (88, 89) onto the
Uprights (84, 85).
89
85
84
88
12
8
79
Wire
Tie
91
C

11. Attach the console assembly.
13. Attach the Storage Latch (54).
12. Attach the Pulse Crossbar (81) to the console
assembly.
NORDICTRACK is a registered trademark of ICON IP, Inc.
Part No. 322141 R0811A Printed in USA © 2011 ICON IP, Inc.
Console
Assembly
11
11
81
Console
Assembly
11 11
11
1
54
92
Large
Barrel
Latch
Knob
2
9
10. Connect the Upright Wire (91) and the Console
Ground Wire (80).
9. Attach the Pulse Crossbar (81).
91
Remove
Wire Tie
80
Ground
Wire
4
4
5
5
12
12
81