Nordpeis Madrid User manual

Assembly Instructions
Art.no: FP-MDR00-100
Nordpeis 18.06.2009
Madrid
GB

2 GB
NB! See separate instructions for the insert
General information
Our surrounds are all made of non-combustible
materials. All our inserts/stoves are tested
according to the latest European requirements
and also to the Norwegian SINTEF standard, which
includes particle tests. Several European countries
however have individual rules for installation of
inserts, stoves and replaces. You as a client are
totally responsible for the fullling of these local
rules concerning the installation in your region/
country. Nordpeis (Northstar) is not responsible
regarding correct installation.
You should check local regulations concerning:
• distance from rebox to combustible/ammable
materials
• insulation materials/requirements between
replace surround and back wall
• size of oor plates in front of replace/stove if
required
• uepipe connection between rebox and chimney
• insulation requirements if uepipe goes through
ammable wall such as a wood wall.
Adjustment
We recommend to stack the surround without glue in
order to adjust the insert prior to perforating the chimney
for the ue connection. Use a spirit level to ensure that
the surround is mounted straight. The insert will expand
with heat and for this reason the surround must not rest
on the insert. (Above the insert there must be a gap
of 3 to 5 mm. Laterally there is no need for gaps, but
between the lower part of the insert and the surround
there must be a gap of at least 2 mm.)
Floor plate
A reproof oor plate must be put in front of the replace
if the oor is of a combustible material.
Powder glue for lling
This is used to repair any notches or wounds in the
concrete. Mix the provided powder glue with water
(the consistency of the glue should be that of tooth
paste). Before you start, use a damp sponge to wet the
concrete surface. This will remove dust and provide for
better adhesion. Fill in any uneven surfaces.
Acrylic glue
This is used for gluing the elements towards wall, gluing
the elements together and for lling joints.
Painting
The surround can be painted 24hrs after that it has
been assembled. Any surface that has been lled needs
to be smoothened with ne sand paper. Use latex or
acrylic based paint (emulsion paint).
Marble/granite
Clean the plates with mild soapy water and remove any
remaining glue.
Fine Fissures
Settlement cracks can appear during the rst year of
new built houses. For this reason, very thin ssures
could appear in the joints between the elements, the
rewall and the chimney. This is entirely normal and
no reason for concern. These small ssures can be
removed by renewing the joint. Scrape out the joint with
a joint scraper and then vacuum clean to remove all the
dirt. Inject acrylic into the joint and even out by using
the ngertip with some soapy water. After about 24
hours the joint can be repainted.
Smaller damages
These are successfully repaired with the provided
powder glue. If the damage is deep, we recommend
lling twice in order to avoid sinking. Fill smaller cracks
and uneven surfaces with a oat or a brush. Smoothen
the surface with a damp sponge or sand paper.
For your own safety, comply with the assembly
instructions. All safety distances are minimum distances.
Installation of the insert must comply with the rules and
regulations of the country where installed. Nordpeis AS
is not responsible for wrongly assembled inserts.
We accept no liability for typographical errors and
changes.

3
GB
Madrid
Insert
NI-25
Steel chimney
Can be installed with steel chimney.
Weight including insert 354 kg
Safety distances Ensure that the safety distances are
complied with.
Please note that these safety distances can vary from
country to country.
The distance to any inammable material in front of the
opening of the insert must be of at least 1 m.
The distance from the glass in the door to a lateral wall,
measured diagonally, must be of at least 600 mm.
The distance from the ue/smoke dome to inammable
wall needs to be at least 300 mm. If the ue goes
through an inammable wall, minimum 230 mm
brickwork must be added between the ue and the wall.
Dry stack the replace until the mantelpiece
element for accurate height and positioning of the
ue/chimney connection.
The distance from the top of the air vent to roof of
inammable material must be at least 380 mm.
Assembly instructions (FIG 1 - FIG 12)
FIG 1: In case of inammable ooring, the area inside
the insert needs to be covered by a steel plate that is
at least 0,7 mm thick. Place the insert as shown and
connect the ue to the chimney.
FIG 2: Place the bottom elements in 90º relative to the
chimney/wall. If needed, adjust with wedges or powder
glue.
FIG 5 / FIG 7: Make sure there is a gap between the
insert and the surround as the insert expand with heat.
Also read the section about adjustment.
FIG 12: When the replace is installed, ll the joints
between the elements with acrylic and smoothen with a
humid sponge or nger so that the joint is well marked.

2383
1400
990
330
982
1382
670 815
Madrid = mm

5
23.02.2009
2/4
Madrid NI-25
9
10
6
5
5
6
2
6
7
98
2
3
4
5
4
11
12
10
6
8
3
5
7
4
1
04.06.2009
2/4
Madrid NI-25
9
10
6
5
5
6
2
8
9
11 10
2
6
7
4
11
12
10
6
8
4
5
3
5
7
4
1
04.06.2009
2/4
Madrid NI-25
9
10
6
5
5
6
2
8
9
11 10
2
6
7
4
11
12
10
6
8
4
5
3
5
7
4
1
04.06.2009
2/4
Madrid NI-25
9
10
6
5
5
6
2
8
9
11 10
2
6
7
4
11
12
10
6
8
4
5
3
5
7
4
1
FIG 1 FIG 2
FIG 3FIG 4

6
18.06.2009
3/4
Madrid NI25
7
13
14
12
11
15
12
13
14
16
18
16
18
17
17
8
15
14
FIG 5FIG 6
FIG 7 FIG 8
18.06.2009
3/4
Madrid NI25
7
13
14
12
11
15
12
13
14
16
18
16
18
17
17
8
15
14
18.06.2009
3/4
Madrid NI25
7
13
14
12
11
15
12
13
14
16
18
16
18
17
17
8
15
14

7
18.06.2009
4/4
Madrid NI25
7
13
14
12
11
26
27
28
18
16
17
18
19
20
21
29 15
14
22
23
25
24
21
19
20
FIG 9 FIG 10
FIG 11
18.06.2009
4/4
Madrid NI25
7
13
14
12
11
26
27
28
18
16
17
18
19
20
21
29
15
14
22
23
25
24
21
19
20
FIG 12