Nordson NT-T10 User manual

Professional Card& Program Developers
And Manuf Acturse
The rights change and upgrade definition and other product information,
without advance notice are preserved by our company
(Please read operating maual carefully before use)
please keep the operating manual carefully
RFID Card Access Control
Operating Manual
Model: NT-T10,NT-T12

-1-
80 00 u se r cards
#

-3--2-
2. System operation
1. factory setting opening password：7890，
programming code:123456
2. quick operation
Press”*”+“waiting to swipe”
(1) Swipe systematic master card to get to system programme
state
(2) Swipe added card to get to adding user card state
(3）swipe deleted card to get to deleting user card state
3. modify programming code and set up systematic master card
(1) Press “8”+ “programming code”+ “#” + “0” +
“ new code”+ “#” + “ new code” + “#”
Note: buzzer sounds means operation success（length of code is
1-8 digits）
(2) press”*” + “programming code” + “#”+ “0”+ “ swipe”
Note：sound of buzzer, master card setting successfully
4. add card type user
Press”*”+” program code”+ “#”+ “1”+“four digits user
code” +“reading card”
Note: user program code is arbitrary four digits and continues to
adding card, the code will automatically gain 1.
5. add password type user
Press “*” + “program code” + “#”+ “2” + “four digits user
code” + “user password” +”#”
Note: four digit user code( if it is 1, then enter “0001”) user
password(0-8 digits)
6. add password& card type user
Press “*” + “ program code” + “#” + “3” + “ four
digits user code” + “four digits user password” + “#” +
“swipe”
7. delete single user
Press “*” + “ program code” + “4” + “user password
or swipe card” + “#”
Note: can continue operate on programming status
8. delete all users
Press “*” + “ program code” + “#” + “5” + “user
password or swipe master card” + “#”
Note: sound of buzzer, operate successfully
9. modify user password
Press “*” + “program code” + “ #” + “6” + “four digits
user code” + “four digits new password” + “#”
Note: on programme state, can continue to operate
10. modify delayed time to open door
Press “*” + “ program code” + “#” + “7” + “
opening time” + “#”
Note: delayed time :0-255s, default to 3s, the longest is 255s.
11. system initialization
(1)press “program code” + “#” + “8” + “programming
status or swipe master card” + “#”
Note: The buzzer will sound once to indicate successful initialization,
clear all the settings. You can also remove the card painted brush
painted increase card delete card initialization data)

-5--4-
6. Us er se tti ngs
4. The da ta copy in g opera tion
The T X D and RXD o f m ain acc e ss cont r ol mach i ne con n e ct to th e
RXD a n d TXD of th e s ame typ e o f vice ac c ess con t rol ma c h ine ,
TXD a n d RXD sho u ld be cro s s-lin k ed,an d t hen en t e r the co p y
pas s word on t h e main ac c ess con t rol mac h ine, T h e red an d g r een
lig h ts flas h i n the sam e t ime on tw o m achin e s,un t i l the ti c k
sou n d heard i t f inish d a ta copy i ng Copy i ng pas s w ord sh o u ld
con s ult fro m a gency o r d istri b utor (N o te: Ma i n a cces s M a chin e s
is ma c hine wi t h data, v i ce acce s s contr o l mach i n e is req u i red
wri t ing dat a )
5. Acce ss cont ro l mode co nvers io n
Acc e ss mode : W hen GLE D a nd GND co n necte d t o powe r , t he gre e n
lig h t flash e s, then d i sconn e ct GLED a n d GND , co n v ersi o n i s
fin i shed wh e n the tic k s ound is h e ard (t h e f acto r y s etti n g i s
def a ult set t ing as Ac c ess mod e ).
Rea d er mode ( W iegan d 2 6 outpu t ): when D 0 a nd GND c o n nect e d t o
pow e r, the gr e en ligh t f lashe s , then di s conn e c t D0 and G N D ,
con v ersio n i s finis h ed when t h e tick so u nd is he a r d Read e r mode
(Wi e gand 34 o u tput) : w hen D1 an d G ND conn e cted t o p o wer, t h e
gre e n light f l ashes , t hen dis c onnec t D 1 and GN D , c o nver s i on
is fi n ished w h en the ti c k sound i s h eard
12. set managed card( add and delete card)
Press “*” + “program code” + “#” + “9” +
“swipe card”
Note: swiping first one is to add card, second
time is to delete card. The function is for
easy access to add and delete user card. After
setting add and delete card, press “*” back
to the add and delete user card state again.
13. set open door general password
Press “*” + “ program code” + “#” + “9” +
four digits password”
Note: factory setting is 7890, cancel general
password by entering 0000
14. exit from programme state
Press “*”, after 10s and no operation, will
exit automatically
3. Jumper setting
（1）J1.active and passive output setting.
When 1 and 2 connection, COM, CO,CN are on-off
signal output.. When 2 and 3 connection and
COM and GND are short out, then it is active
signal output.
（2）J2. RESET reset setting. Initialize programming
code after electrify short j2
15. Tamper alarm turned on or off
Cancel the alarm: Enter the password to open the door in an
alarm state temporarily closed alarm
Close Alarm: Brush Remove the card three times to close the tamper alarm
Open alarm: Brush increase card three times to open the tamper alarm

-7--6-
+12 V
GND
COM
NC
BTN
GLE D
NO
D1
D0
GND
Powe r
12V
+12V
GND
D1
D0
LED
-
+
TXD
RXD
TXD
RXD
Note: P l ease cha n g e the o p erating m o d e when use
access contr o l m a c hine as access contr o l r e a der.
TXD and RXD is dat a c o p y ing interface , two ho s t s
can be copied each other, when acc e s s wi r i n g
should set t w o TX D and RXD r everse o p e ration.
Th e s ame t y pe of a c ces s c ont r ol
Data copy
7.1 Commo n powe r s uppl y diagr am
Fi g ure 1
Acce ss con t rol
Acc e s s contro l r eader
7. Wir ing dia gram
+1 2V
GN D
CO M
NC
BT N
LE D
NO
D1
D0
GN D
TX D
RX D
Re d
Bl ac k
Gr ey
Pu rp le
Br ow n
Bl ue
Ye ll ow
Wh it e
Gr ee n
Bl ac k
Or an ge
Pi nk
12 V+ D C re gulat ed p ow er i np ut
12 V- D C re gulat ed p ow er i np ut
Re la y pu blic en d, co nn ec t GN D
Re la y cl osed en d( Co nn ec t po si ti ve e le ctric loc k)
Ex it b ut ton one e nd (t he o th er e nd c on ne ct ed g nd)
Re ad er m ode
Re la y no rmally op en e nd (C on ne ct p os it iv e elect ri c lo ck )
WG D 1
WG D 0
Da ta c op ying in te rf ac e
Da ta c op ying in te rf ac e
12 V- D C Re gulat ed p ow er i np ut
-+
-+

-9--8-
Fi g ure 2
+12 V
GND
NO
NC
PUS H
+12V
GND
COM
NC
BTN
GLE D
NO
D1
D0
GND
TXD
RXD
+12 V
GND
D1
D0
LED
Wi eg an d outpu t
Acce ss cont rol
Spe c i al Power S u pply
Acc e s s contro l ler
Da ta c op y
Note: P l e a s e change the operating mode when use
access control machine as access control r e a d e r .
TXD and RXD is data copying interface , two host s
can be co p i e d ea c h other, when access wi r i n g
should s e t two T X D and R X D reverse operation.
8. Cautions and failure analysis
(1) Notes
◆ The user card that authorized by adding card or deleting
card only can be deleted by swiping
◆ Tamper alarm is light sensor, the light changes strongly,
hosts two minutes ,then the alarm returns to normal
◆ First time use please change the password that for opening
the door and host programming.
◆ Note input or output Wiegand interface mode, details can
th
refer to 5 setting.
◆ When two hosts copy each other they should be cross-connected
TXD and RXD
◆ Note distinguish the main and vice machine when copying data ,
to avoid the access control data is cleared
(2) Failure analysis
Card can not open the door:
◆ Check whether the card registration
◆ Check the wiring if there is a problem
◆ access control mode is correct or not
Can not read card:
◆ Check whether the correct card type or card is damaged
◆ Check whether an external card reader and the host are placed
too close
7.2 S p ecial power c onne c ting d iagra m
-+
-+