Nortel Ethernet Routing Switch 8600 User manual

Nortel Ethernet Routing Switch 8600
Installation — Chassis
Release: 5.0
Document Revision: 02.01
www.nortel.com
NN46205-303 316314-G Rev 01
.

Nortel Ethernet Routing Switch 8600
Release: 5.0
Publication: NN46205-303
Document status: Standard
Document release date: 30 May 2008
Copyright © 2008 Nortel Networks
All Rights Reserved.
Printed in Canada, India, and the United States of America
LEGAL NOTICE
While the information in this document is believed to be accurate and reliable, except as otherwise expressly
agreed to in writing NORTEL PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF
ANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document are
subject to change without notice.
Nortel, the Nortel logo, the Globemark, and Passport are trademarks of Nortel Networks.
All other trademarks are the property of their respective owners.
ATTENTION
For information about the regulatory and safety precautions, read "Regulatory messages and safety
precautions" in this guide.
For information about the software license, read "Software license" in this guide.
.

3
.
Contents
Regulatory Information and Safety Precautions 7
Software license 19
New in this release 23
Features 23
Dual input AC power supply 23
RS modules 23
Other changes 24
Air filter 24
Document changes 24
Document corrections 24
Part numbers 24
Troubleshooting 24
Introduction 25
Chassis installation fundamentals 27
8010co chassis 28
8010 chassis 29
8006 chassis 31
8003 chassis 32
Power supplies 33
Fan trays and cooling modules 34
Site requirements 35
Space requirements 35
Hardware requirements 35
8010, 8006, and 8003 chassis 35
8010co chassis 39
Successful installation verification 41
8010, 8006, and 8003 chassis installation 43
Chassis installation procedures 43
Chassis installation time requirements 45
Positioning the chassis on a flat surface 45
Mounting the chassis in an equipment rack 45
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

4
Installing the cable management brackets 52
8010co chassis installation 57
Chassis installation procedures 57
Chassis installation time requirements 59
Mounting the chassis in a two-post rack 59
Installing the cable management brackets 63
Installing 8004DC power supplies with the BIP 65
Grounding the chassis 65
Switch operations 71
Powering on DC power supplies 71
Powering on AC power supplies 73
Resetting the switch 73
Installing removable flash memory cards 74
Removing removable flash memory cards 75
Protecting memory card files 77
Common procedures 79
Reducing the chassis weight 79
Part numbers 81
Technical specifications 83
Chassis weight 83
Rack-mount 84
Model 8003AC power supply 84
Model 8004AC power supply 85
Model 8005AC power supply 85
Model 8005DI AC power supply 86
Model 8004DC power supply 87
Model 8005DC power supply 88
Component input power 89
Power supply selection 90
8010co chassis 91
Physical specifications 91
Network Equipment Building Standard 92
Environmental specifications 92
Maximum airflow 92
International regulatory requirements 92
8010 chassis 94
Physical specifications 94
Environmental specifications 94
International regulatory requirements 95
8006 chassis 96
Physical specifications 96
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

5
Environmental specifications 97
International regulatory requirements 97
8003 chassis 99
Physical specifications 99
Environmental specifications 99
International regulatory requirements 100
Translations of safety messages 103
Class A device caution statement 103
Electrostatic discharge caution statement 104
Laser fiber optic warning statement 105
Lifting 8010co chassis warning statement 106
Index 109
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

6
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

7
.
Regulatory Information and Safety
Precautions
Read the information in this section to learn about regulatory conformities
and compliances.
International Regulatory Statements of Conformity
This is to certify that the Nortel 8000 Series chassis and components
installed within the chassis were evaluated to the international regulatory
standards for electromagnetic compliance (EMC) and safety and were
found to have met the requirements for the following international
standards:
•EMC—Electromagnetic Emissions—CISPR 22, Class A
•EMC—Electromagnetic Immunity—CISPR 24
•Electrical Safety—IEC 60950, with CB member national deviations
Further, the equipment has been certified as compliant with the national
standards as detailed in the following sections.
National Electromagnetic Compliance (EMC) Statements of
Compliance
FCC Statement (USA only)
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the Federal Communications
Commission (FCC) rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy. If it is not installed and used in accordance
with the instruction manual, it may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case users will be required to take
whatever measures may be necessary to correct the interference at their
own expense.
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

8Regulatory Information and Safety Precautions
ICES Statement (Canada only)
Canadian Department of Communications Radio Interference
Regulations
This digital apparatus (8000 Series chassis and installed components)
does not exceed the Class A limits for radio-noise emissions from
digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Règlement sur le brouillage radioélectrique du ministère des
Communications
Cet appareil numérique (8000 Series chassis) respecte les limites de bruits
radioélectriques visant les appareils numériques de classe A prescrites
dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
CE Marking Statement (Europe only)
EN 55 022 Statements
This is to certify that the Nortel 8000 Series chassis and components
installed within the chassis are shielded against the generation of radio
interference in accordance with the application of Council Directive
2004/108/EC. Conformity is declared by the application of EN 55 022
Class A (CISPR 22).
CAUTION
This device is a Class A product. Operation of this equipment
in a residential area is likely to cause harmful interference, in
which case users are required to take appropriate measures
necessary to correct the interference at their own expense.
EN 55 024 Statement
This is to certify that the Nortel 8000 Series chassis is shielded against the
susceptibility to radio interference in accordance with the application of
Council Directive 2004/108/EC. Conformity is declared by the application
of EN 55 024 (CISPR 24).
EN 300386 Statement
The Ethernet Routing Switch 8000 Series chassis complies with the
requirements of EN 300386 V1.3.3 for emissions and for immunity for a
Class A device intended for use in either Telecommunications centre or
locations other than telecommunications centres given the performance
criteria as specified by the manufacturer.
EC Declaration of Conformity
This product conforms to the provisions of the R&TTE Directive
1999/5/EC.
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

National Electromagnetic Compliance (EMC) Statements of Compliance 9
European Union and European Free Trade Association (EFTA) Notice
All products labeled with the CE marking comply with R&TTE Directive
(1999/5/EEC) which includes the Electromagnetic Compliance (EMC)
Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC)
issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following
European Norms (ENs). The equivalent international standards are listed
in parenthesis.
•EN 55022 (CISPR 22)–Electromagnetic Interference
•EN 55024 (IEC 61000-4-2, -3, -4, -5, -6, -8, -11)–Electromagnetic
Immunity
•EN 61000-3-2 (IEC 610000-3-2)–Power Line Harmonics
•EN 61000-3-3 (IEC 610000-3-3)–Power Line Flicker
VCCI Statement (Japan/Nippon only)
This is a Class A product based on the standard of the Voluntary Control
Council for Interference (VCCI) for information technology equipment.
If this equipment is used in a domestic environment, radio disturbance
may arise. When such trouble occurs, the user may be required to take
corrective actions.
BSMI Statement for 8010, 8006 and 8003 Chassis (Taiwan only)
This is a Class A product based on the standard of the Bureau of
Standards, Metrology and Inspection (BSMI) CNS 13438, Class A.
MIC Notice for 8010, 8006, 8003 Chassis (Republic of Korea only)
This device has been approved for use in Business applications only per
the Class A requirements of the Republic of Korea Ministry of Information
and Communications (MIC). This device may not be sold for use in a
non-business application.
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.

10 Regulatory Information and Safety Precautions
National Safety Statements of Compliance
CE Marking Statement (Europe only)
EN 60 950 Statement
This is to certify that the Nortel 8000 Series chassis and components
installed within the chassis are in compliance with the requirements of EN
60 950 in accordance with the Low Voltage Directive. Additional national
differences for all European Union countries have been evaluated for
compliance. Some components installed within the 8000 Series chassis
may use a nickel-metal hydride (NiMH) and/or lithium-ion battery. The
NiMH and lithium-ion batteries are long-life batteries, and it is very possible
that you will never need to replace them. However, should you need to
replace them, refer to the individual component manual for directions on
replacement and disposal of the battery.
NOM Statement 8010, 8006, and 8003 Chassis (Mexico only)
The following information is provided on the devices described in this
document in compliance with the safety requirements of the Norma Oficial
Méxicana (NOM):
Exporter: Nortel Networks, Inc.
4655 Great America Parkway
Santa Clara CA 95054 USA
Importer: Nortel Networks de México, S.A. de C.V.
Avenida Insurgentes Sur #1605
Piso 30, Oficina
Col. San Jose Insurgentes
Deleg-Benito Juarez
Nortel Ethernet Routing Switch 8600
Installation — Chassis
NN46205-303 02.01 Standard
30 May 2008
Copyright © 2008 Nortel Networks
.