Norwood LumberMate LM29V2 User manual

7.5 KW / 4 KW ELECTRIC
MOTOR PACKAGE
MILL-ELEC-S1-MANEN
ORIGINAL INSTRUCTIONS
ENSEMBLEDE
MOTEUR ÉLECTRIQUE
DE 7,5 KW / 4 KW
INSTRUCTIONS ORIGINALES
7,5 KW / 4 KW
SÄHKÖPAKKAUS
ALKUPERÄISET OHJEET
7,5 KW / 4 KW
ELEKTROMOTOR
URSPRÜNGLICHE ANLEITUNG
GRIPEKLO (LM29& MN26)
ORIGINAL ANVISNINGER
KIT DE TRAVA DE CAME
(LM29 E MN26)
INSTRUÇÕES ORIGINAIS
NOMBRE DEL ADJUNTO
EN ESPAÑOL
INSTRUCCIONES ORIGINALES
7,5 KW/4 KW ELPAKET
BRUKSANVISNING ORIGINAL
»LumberMate LM29V2, LM30
»LumberMan MN26V2, MN27
»LumberPro HD36V2, HD36
MILL-ELEC-S1-MANEN (2021-07-14).indd 1MILL-ELEC-S1-MANEN (2021-07-14).indd 1 2021-07-14 3:53:59 PM2021-07-14 3:53:59 PM

MILL-ELEC-S1-MANEN (2021-07-14).indd 2MILL-ELEC-S1-MANEN (2021-07-14).indd 2 2021-07-14 3:53:59 PM2021-07-14 3:53:59 PM

EN–1 7.5 kW / 4 kW ELECTRIC MOTOR
PACKAGE
EN–1 Safety Instructions
EN–3 Saftey Instructions
EN–5 Parts List: HD26V2 (7.5 kW electric motor (S1)
(400V, 3 Phs) package)
EN–6 Parts List: LM29V2-75KW-EU-400V (7.5 kW
electric motor (S1) (400V, 3Phs) package)
EN–7 Parts List: MN26V2-004KW-EU-400V (4 kW
electric motor (S1) (400V, 3 Phs)package)
EN–8 Technical Data
EN–9 Assembly
EN–10 Motor Installation
EN–17 Safety Switch Assembly
EN–20 Layout of Controls
EN–21 Operating the Electrical Equipment
FR–1 ENSEMBLE DE MOTEUR ÉLECTRIQUE
DE 7,5 kW / 4 kW
FR–1 Instructions de sécurité
FR–3 Instructions de sécurité
FR–5 Liste des pièces : HD26V2 -75KW-EU-400V
(Ensemble de moteur électrique de 7,5 kW (S1),
400 V, triphasé)
FR–6 Parts List: LM29V2 -75KW-EU-400V (Ensemble
de moteur électrique de 7,5 kW (S1), 400 V,
triphasé)
FR–7 Liste des pièces : MN26V2-004KW-EU-400V
(Ensemble de moteur électrique de 4 kW (S1)
400 V, triphasé)
FR–8 Données techniques
FR–9 Assemblage
FR–10 Installation du moteur
FR–17 Assemblage de l’interrupteur de sécurité
FR–20 Disposition des commandes
FR–21 Utilisation de l’équipement électrique
FI–1 7,5 kW / 4 kW SÄHKÖPAKKAUS
FI–1 Turvallisuusohjeet
FI–3 Turvallisuusohjeet
FI–5 Osaluettelo: HD36v2-75KW-EU-400V (7,5
kW sähkömoottori (S1) (400 V, 3-vaiheinen)
-pakkaus)
FI–6 Osaluettelo: LM29v2-75KW-EU-400V (7,5
kW sähkömoottori (S1) (400 V, 3-vaiheinen)
-pakkaus)
FI–7 Osaluettelo: MN26v2-004KW-EU-400V (4
kW sähkömoottori (S1) (400 V, 3-vaiheinen)
-pakkaus)
FI–8 Tekniset tiedot
FI–9 Asennus
FI–10 Moottorin asennus
FI–17 Turvakytkimen asentaminen
FI–20 Ohjaimien sijainti
FI–21 Sähköjärjestelmien käyttö
DE–1 7,5 kW / 4 kW ELEKTROMOTOR
DE–1 Sicherheitsanweisungen
DE–3 Sicherheitsanweisungen
DE–5 Teileliste: HD36v2-75KW-EU-400V (7,5 kW
Elektromotor (S1) (400 V, 3 Phasen))
DE–6 Teileliste: LM29v2-75KW-EU-400V (7,5 kW
Elektromotor (S1) (400 V, 3 Phasen))
DE–7 Teileliste: MN26v2-004KW-EU-400V (4 kW
Elektromotor (S1) (400 V, 3 Phasen))
DE–8 Technische Daten
DE–9 Zusammenbau und Montage
DE–10 Motorinstallation
DE–17 Montage des Sicherheitsschalters
DE–20 Aufbau der Bedienelemente
DE–21 Bedienung der elektrischen Ausrüstung
NO–1 Installasjons- Og Driftinstruksjoner
For Motordrevet
NO–1 Saghode Og Motordrift
NO–1 Sikkerhetsinstruksjoner
SE–1 7,5 kW/4 kW ELPAKET
SE–1 Säkerhetsinstruktioner
SE–3 Säkerhetsinstruktioner
SE–5 Lista över delar: HD36v2-75KW-EU-400V (7,5 kW
elmotor (S1) (400 V, trefas))
SE–6 Lista över delar: LM29v2-75KW-EU-400V (7,5 kW
elmotor (S1) (400 V, trefas))
SE–7 Lista över delar: MN26v2-004KW-EU-400V (4 kW
elmotor (S1) (400 V, trefas))
SE–8 Tekniska data
SE–9 Montering
SE–10 Installation av motorn
SE–17 Säkerhetsbrytarenhet
SE–20 Kontrollernas layout
SE–21 Användning av den elektriska utrustningen
MILL-ELEC-S1-MANEN (2021-07-14).indd 3MILL-ELEC-S1-MANEN (2021-07-14).indd 3 2021-07-14 3:53:59 PM2021-07-14 3:53:59 PM

Text: S. Cabrit
First Edition: 2020-09-20
Latest Revision: 2021-07-14
Copyright © 2020, 2021 Norwood Industries Inc.
All rights reserved. No part of this publication may
be reproduced in any form or by any means without
permission in writing from the publisher, Norwood
Industries Inc.
The trade-names Norwood®, LumberMax®, LumberPro®, LumberMate®,
LumberMan®, LumberLite®, LM Pro®, HD38®, HD36®, LM30®, LM29®,
MN27®, MN26®, PortaMill®, Frontier®, OS®, OS23®, OS27®, OS31®,
BladeMate®, Duradeck®, IntelliSet®, MultiMate®, Omega®, SabreBar®,
SabreChain®, SabreTooth®, Sawmill TV®, Sawyer-Assist®, SkidMate®,
Trekker®, the LumberJack®mascot, “Forest. Fun. Freedom.”, the “chevron”
graphic and the color orange (as related to sawmills, edgers, skidders
& related equipment) are registered trademarks owned by Norwood
Industries Inc. in multiple jurisdictions. Functional and design elements
of Norwood sawmills and log handling equipment are protected by
registered patents and pending patents in multiple jurisdictions.
U.S. Patent Nos. 6,932,555, 9,102,074, 7,784,387, 8,215,216,
8,261,645, 8,261,647, 8,276,493, 8,820,727, 9,676,116, 10,843,370,
D816742, D818013, D834623, D831711, D639,319, D654,101,
D638,040, 8,479,628 — Canada Patent Nos. 2,432,863, 2,488,216,
132823, 2,541,734, 2,687,619, 2,687,622, 2,687,623, 2,688,407,
2,696,974, 2,782,909, 2,806,456, 2,800,791, 2,969,794, 3,037,006,
134185, 133049, 169785, 169786, 169787, 169788 — EU Patent Nos.
EP 2,746,009 B1, EP 2,332,706 B1, EP 2,332,683 B1, EP 2,684,631,
EP 2,332,704, EP 2,759,384, 1117196-0001; 001212393-0001;
001217277-0001, 001214662-0001, 003736255-0001, 003736255-0002,
003736255-0003, 003736255-0004 — Brazil Patent Nos. BR30 2012
003601-1, BR10 2013 025882-2, BR10 2013 025883-0, PI 1004044-7,
PI 1010352-0, DI 7001877-4, DI 7001876-6, PI 1009180-7 — Australia
Patent Nos. 201710614, 201710616, 201710615 — China Patent No.
4192870. Other patents pending in multiple jurisdictions.
Norwood Industries Inc. is constantly developing its equipment.
Wereserve the right to make changes to the design, construction and
finish of our equipment without notice.
Photographs and illustrations in this manual may show optional
attachments or previous models and parts.
Telephone: [phone]
E-mail: [e-mail]
Website: www.NorwoodSawmills.com
Norwood Industries Inc.
2267 15/16 Side Road East
Oro-Medonte ON L0L 1T0
Canada
®
MILL-ELEC-S1-MANEN (2021-07-14).indd 4MILL-ELEC-S1-MANEN (2021-07-14).indd 4 2021-07-14 3:53:59 PM2021-07-14 3:53:59 PM

The sawmill, its options, accessories,
engine and blades (the “equipment”)
are extremely dangerous and can
cause severe injury or death.To avoid
serious injury, the equipment must always be
handled, operated and stored with the utmost
care and good judgment and in accordance
with all warnings, cautions, instructions and
procedures contained in this manual, in the
engine manual, in the instructions enclosed
with optional accessories and on the decals
posted on the equipment. Failure to use good
judgment or to follow any of these warnings,
cautions, instructions and procedures can
result in severe injury or death.
WARNING! This symbol means “Pay Extra
Attention” and is always followed by a warning
about a danger that can cause severe injury.
This symbol means “Pay Attention” and is
always followed by a caution or warning of
great importance for safety or sawing results.
For your own safety and the safety of others,
do not begin working with this equipment
before having read and understood this entire
manual, the engine manual, the instructions
enclosed with optional accessories and the decals
posted on the equipment.
Save all instructions for future reference. Keep all decals
in place, clean and readable. Replace any damaged or
missing decals without delay.
DISCLAIMER
Norwood Industries Inc. and Norwood Sawmills
U.S.A. Inc. disclaim any responsibility or
liability, in negligence or otherwise, for any
injuries, damages or losses of any kind arising
during the course of assembling, operating or
handling this equipment, options, accessories
or blades howsoever caused.
Responsibility for final inspection of the
sawmill parts and components, and the
assembly, maintenance and safe use of the
equipment, lies solely with the person(s) who
assembles and operates the equipment and
handles blades.
Persons under the age of 18 may not work with the
equipment or handle blades.
Only persons who meet all of the following
requirements are qualified to operate the equipment
or handle blades.
Qualified operators:
a. Have read and fully understood all the warnings,
cautions, instructions and procedures in this manual,
the engine manual and all instructions enclosed with
optional accessories, and on all decals posted on
the equipment,
b. Are well rested,
c. Are in good physical health with good eyesight,
d. Have not consumed alcohol or drugs, and
Safety Instructions
EN–1EN–1
EN
7.5 Kw / 4 Kw
Electric Motor
Package
MILL-ELEC-S1-MANEN (2021-07-14).indd 1MILL-ELEC-S1-MANEN (2021-07-14).indd 1 2021-07-14 3:53:59 PM2021-07-14 3:53:59 PM

e. Are not taking medication that can impair judgment,
reaction times, mobility, alertness or otherwise cause
negative side effects.
Persons who fail to meet any of these requirements are
not qualified to use the equipment or handle blades.
Wear protective gloves when working with the
equipment or handling blades. Risk of cutting
injuries when handling blades. Blades and
engine can be hot immediately after sawing.
Wear approved hearing protection when
operating the equipment. Hearing can
be permanently impaired after only short
exposure to high-frequency sounds.
Wear approved close-fitting safety goggles
when working with the equipment or handling
blades.
Wear approved protective footwear with saw
protection, steel toe-cap and non-slip sole
when working with the equipment or handling
blades.
Wear full-length protective pants when working
with the equipment or handling blades. Never
wear loose-fitting clothing, scarves, jewellery
or similar long items that can get caught when
working with the equipment. Always secure loose hair
before working with the equipment.
Wear respiration protection when working
with the equipment. Long term inhalation of
sawdust and the engine’s exhaust fumes can
represent a health risk.
WARNING! Cutting tools: Incorrect use of
the equipment or unsafe blade handling can
cause life-threatening injuries. Blades are
extremely sharp and dangerous.
WARNING! Sawhead drop danger:
Pressing downward, even slightly on the
winch adjustment knob/spring, will release
the winch brake. Releasing the winch brake
will cause the sawhead to drop quickly and violently
causing serious injury.
WARNING! Crush danger: The log rests can
drop quickly when the log rest lever is
activated causing serious injury to your
hand. Keep your hands clear of the log rests
when activating the log rest lever and where milling or
log handling operations may accidentally activate the log
rest lever.
Always stay behind the sawhead after the engine
has started.
Review and follow all of the safety instructions in the
sawmill manual and in the engine manual.
The Worksite
Operate the equipment and handle blades in full
daylight or under adequate site lighting cast from at
least four sides to minimize shadows.
Keep the work area clean, free of clutter, pets,
children, obstacles, hazards or distractions.
Keep all children and animals well away from the
equipment and blades at all times.
A broken blade can be ejected out of the sawdust
chute at high velocity. Keep all people and pets
completely clear of the path of the sawdust chute.
Remember that, as the carriage moves, so do the
blade and the path of the sawdust chute.
The risk of blade breakage increases when a blade
is not properly and regularly profiled and maintained
and/or when a blade is used past its service life.
Illustration below depicts view of work site as
seen from above. It sets out the minimum safety
distance for persons other than the operator. While
operating the equipment, the operator must be within
the stipulated area (*) bounded between the broken
line and the nearest side of the sawmill.
While the equipment is running, persons other than
the operator must observe the safety distances
stipulated in the illustration.
The minimum safety distance away from the
equipment for persons other than the operator on the
left side of the sawmill (the side opposite the
operator’s side) is 15m (50 feet) due to the risk of
blades being ejected out of the sawdust chute. On all
other sides of the equipment, the minimum distance
away from the equipment for persons other than the
operator is 6m (20 feet).
A broken blade can be ejected out of the sawdust
chute at high velocity. Keep all people and pets
completely clear of the path of the sawdust chute.
Remember that, as the carriage moves, so do the
blade and the path of the sawdust chute.
EN–2
MILL-ELEC-S1-MANEN (2021-07-14).indd 2MILL-ELEC-S1-MANEN (2021-07-14).indd 2 2021-07-14 3:54:00 PM2021-07-14 3:54:00 PM

Saftey Instructions
Risk of being crushed by the carriage.
Risk of tripping on the rails or the cross-bunks.
Never walk on the rails or the cross-bunks.
Never step across the rails.
Risk of being crushed between the sawmill and a
moving log.
Set up the equipment on level ground so that there is
at least 3m (10 feet) of level ground around the rails
and that there are no obstacles within that area.
Do not stand between the pile of logs and the
equipment.
Always stand at the side of the pile of logs when
handlings the logs. Never stand where you are at
risk of being hit by a rolling log.
Keep at least a 5lb. fully-charged ABC dry-chemical
fire extinguisher visible and easily accessible at the
worksite.
Keep a fully-stocked first-aid kit visible and easily
accessible at the worksite.
Never work alone. Make sure that there are other
adults within hearing distance should you need to
call for help.
Control Panel OFF Switch
The control panel is equipped with an OFF switch.
Test the OFF switch before each use once a day: Start
the electric motor ON and press the OFF switch. If it
does not shut the electric motor OFF, it is not working
therefore stop using the equipment and contact Norwood
immediately to order a replacement.
Site Operating Conditions
a. Altitude is not exceeding 1000m,
b. Maximum ambient air temperature is +40 °C,
minimum ambient air temperature is not less than 0
°C,
c. Storage and transportation temperature range is
-15 °C ~ 40 °C.
d. The relative humidity does not exceed 50% at a
maximum temperature of +40 °C, higher relative
humidity may be permitted at lower temperature (e.g.
90% @ 20 °C).
e. The machine can be stored or transported under
ambient temperatures between -25 °C and +55 °C.
Through poor conditions of the electrical MAINS, shortly
voltage drops can appear when starting the
EQUIPMENT.
This can influence other equipment (e.g. Blinking of a
lamp). If the MAINS-IMPEDANCE Zmax<0.252OHM,
such disturbances are not expected. (In case of need,
you may contact your local supply authority for further
information).
Before the machine is connected in TN-S power supply
system, the end user shall perform the test according to
clause 18.2 of EN 60204-1.
Operating the equipment
Cutting tools: Stand behind the carriage and keep
both your hands on the push handle while operating
the equipment. Never stand in front of the carriage
or blade. Never pull the carriage through the cut.
Sawhead drop danger: Pressing downward, even
slightly on the winch adjustment knob/spring, will
release the winch brake. Releasing the winch brake
will cause the sawhead to drop quickly and violently
causing serious injury.
Never open the blade and bandwheel guards while
the motor is running.
Before opening the blade and bandwheel guards,
turn the control panel to the OFF position and
disconnect (unplug) the power supply electrical cable
from your electrical outlet.
Coiled blades can spring apart with considerable
force and unpredictably in any direction. Handle
coiled blades, including those packaged in boxes,
with the utmost care.
The blade and bandwheel guards are shatter
resistant to temperatures as low as -28°C. Never
operate the equipment in temperatures at or below
-28°C.
Ensure that the equipment is assembled and
maintained in accordance with this manual, the
sawmill manual and the instructions enclosed with
optional accessories.
Never use the equipment to cut anything other than
wood.
Never add hardware or attachments of any kind to
the equipment other than those manufactured by
Norwood Industries Inc. specifically for the
equipment. Never modify the equipment.
EN–3
MILL-ELEC-S1-MANEN (2021-07-14).indd 3MILL-ELEC-S1-MANEN (2021-07-14).indd 3 2021-07-14 3:54:01 PM2021-07-14 3:54:01 PM

Before operating the equipment, ensure that:
• all maintenance procedures have been properly carried
out;
• the blade is disengaged;
• the equipment stands firmly and securely and the rails
are fully supported along their full length;
• the carriage retaining keepers and bed end stops are
properly and securely installed;
• all components, fasteners, cables and parts are properly
and securely installed and in good working order;
• all safety features are properly and securely installed
and in good working order including, but not limited to,
the electric motor circuit breaking safety switch, the
blade/bandwheel brake, the sawdust chute cage, and
blade and bandwheel guards are correctly installed and
securely locked; and
• the blade is correctly installed, properly tensioned and
aligned, and can rotate freely in the correct direction.
Before each cut, ensure that:
• no person other than the operator and no pets are within
the minimum safety distances;
• the worksite is free of objects that the operator can trip
over, hazards or distractions.
• the blade will clear the log posts and log dogs;
• the rails and track are free of debris;
• the log is firmly secured with the log clamping
mechanisms;
• the adjustable blade guide will clear the widest portion of
the next cut by one inch and is secured in place;
• the blade and bandwheel guards are correctly installed
and securely locked; and
• the operator is wearing all personal protective equipment.
At regular intervals during operation, ensure that no
person other than the operator and no pets are within the
minimum safety distances.
Turn the motor off if you are going to leave the operating
station behind the carriage, even just temporarily, for
example when loading or repositioning logs or removing
lumber.
Never overreach. Keep proper footing at all times.
Discontinue operating the equipment or handling blades
if you become fatigued or distracted.
Stay focused and alert. Watch what you are doing. Use
common sense.
If your sawmill is equipped with an electric powered
motor:
Risk of electric shock! Hazardous voltage inside the
disconnect box, starter box and at the electric motor can
cause shock, burns or death.
Electrical short danger! Ensure that you do not short
out any part of the electrical system. Shorting out
the electrical system can cause both of the sawhead
support cables to simultaneously break suddenly and the
sawhead to drop violently causing serious injury.
Only a qualified electrician can open the electrical
equipment. All electrical installation, service and
maintenance work must be performed by a qualified
electrician and must be performed in accordance to
applicable electrical codes. Failure to do so can result in
serious injury or death.
Before installing, servicing or maintaining any of the
electrical equipment, turn the control panel to the OFF
position and disconnect (unplug) the power supply
electrical cable from your electrical outlet. Follow all
applicable electrical codes.
If you have any reason to suspect that there is anything
wrong with the electrical system, immediately disconnect
(unplug) the power supply electrical cable from your
electrical outlet, turn the control panel to the OFF
position and remove the ignition key and contact a
qualified electrician to service the electrical equipment.
Do not operate the equipment until it has been serviced
by a qualified electrician and certified fully safe to operate
Storing the Equipment
When storing the equipment, turn the control panel to the
OFF position and disconnect (unplug) the power supply
electrical cable from your electrical outlet. Take any other
measures necessary to prevent unauthorized operators
from accessing or starting the equipment.
Ensure that the blade and bandwheel guards are
correctly installed and securely locked.
Lower the sawhead to its lowest position.
Always store the equipment in a secure and locked
location completely inaccessible by children or any
persons.
When not in use or when unattended, even for short
periods of time such as during breaks, remove the blade
from the sawmill and store it in a location inaccessible by
children or any persons. In addition to being a wise safety
precaution, removing the blade from the sawmill ensures
that it is not stored under tension and so prevents
premature blade fatigue.
When not in use, take measures to secure thecarriage to
the bed to prevent the carriage from being blown or
inadvertently rolled along the track.
Always store all blades in a secure and locked location
completely inaccessible by children or any persons.
If your sawmill is equipped with the optional trailer
package: When storing the equipment, always remove
the drawbar and wheels and secure them in a different
location and take any other measures necessary to
prevent unauthorized persons from accessing or moving
the equipment.
The machine can be stored under ambient
tempera¬tures between -25 °C and +55 °C.
When storing the equipment, turn the electric motor OFF
and remove the blade. Disconnect (unplug) the power
supply electrical cable from your electrical outlet.
EN–4
MILL-ELEC-S1-MANEN (2021-07-14).indd 4MILL-ELEC-S1-MANEN (2021-07-14).indd 4 2021-07-14 3:54:01 PM2021-07-14 3:54:01 PM

Qty. Description Norwood No.
1 Electric motor - Motor - 7.5kW S1 duty, 2900 RPM, 400/690V 50 HZ ENGE-11KWS3-EU
HD36-BOX #14D (E.U., 7.5kW, 400/230V, 3PH Electric)
1 Belt - Drive belt (HD36 Electric) (B92-V) HD36-DBB92
1 Bushing - 38mm QD metric (for MILL-SHV46IN & MILL-SHV56IN sheaves) (HD36, LM29) MILL-BUSH38MM
1 Sheave - 6.8" sheave - bushing MILL-BUSH38MM required MILL-SHV68IN
2 Rear leg assembly (LM34, HD36) - Spacer LM34-C0220-SPC
2 Sawhead lift cable (HD36 ELECTRIC) (125" OAL) (Colored End) HD36-SHCBL-ELEC
1 Manual - Electric Motor System (S1) (English)(LM29v2, MN26v2, HD36, HD38) MILL-ELEC-S1-MANEN
MILL-BAG #ELECT - 400/230V, E.U. Electric
1 Safety switch key LM34-SFTY2
10 3/8 nut - flanged nylon lock nut FASN-38LNF
6 3/8 nut - flanged (regular) FASN-38RFL
12 3/8 x 1" bolt - flanged bolt FASB-38X1L
5 Cable tie - Reusable nylon 6" black DBKR-CTIE6
3 Cable tie mount - Adhesive mount DBKR-CTMA
2 3/8 x 2" bolt - flanged bolt FASB-38X2F
4 3/8 x 1 1/2" bolt - flanged bolt FASB-3815F
2 #10 - 32 nut - hex FASN-1032H
2 #10 - 32 x 1 1/2" screw - Phillips machine screw FASS-10112PMS
2 #6 - 5/8 screw - Phillips truss head tapping screw FASS-658PT
HD36-BOX #15 (E.U., 7.5kW, 400V, 3PH Electric)
1 Electric - Control Panel w/controler&12v converter - 4 to 7.5kW,Y-D,400V,3PH,S1(2020) ENGE-YD-S1-400V-CP-12V
Control Panel Assembly (factory-assembled):
2 Electric – Safety switch for back cover w/ 1.6m wiring (LMMNv2, HD36v2) ENGE-SFTY-001
1 Electric - Remote control box clamping bracket (LM29v2, MN26v2, HD36) MILL-EUELEC-0012
2 Electric - Control panel clamp (HD36) (from 2020) N/A
4 M4 x 8mm screw N/A
2 M4 x 30mm screw N/A
2 M4 nut N/A
1 Power cable clamp N/A
Parts List: HD26V2 (7.5 kW electric motor (S1) (400V, 3 Phs) package)
EN–5
MILL-ELEC-S1-MANEN (2021-07-14).indd 5MILL-ELEC-S1-MANEN (2021-07-14).indd 5 2021-07-14 3:54:02 PM2021-07-14 3:54:02 PM

Qty. Description Norwood No.
1 Electric motor - Motor - 7.5kW S1 duty, 2900 RPM, 400/690V 50 HZ ENGE-11KWS3-EU
LM29V2-BOX #15C (E.U., 7.5kW, 400/230V, 3PH Electric)
1 Sheave - 5.0" sheave (HD36) (bushing MILL-BUSH38MM req'd) MILL-SHV50IN
1 Bushing - 38mm QD metric (for MILL-SHV46IN & MILL-SHV56IN sheaves) (HD36, LM29) MILL-BUSH38MM
1 Manual - Electric Motor System (S1) (English)(LM29v2, MN26v2, HD36, HD38) MILL-ELEC-S1-MANEN
LMMNv2-Bag #X (Safety Switches Bag -)
4 M5 x 14mm screw - hex socket screw FASS-M514S
2 Safety switch - Limit switch bandwheel cover (1NO/1NC)(LM29v2, MN26v2, OS23, O27, OS31) FRON-SFTY1
MILLV2-BAG #ELECT - 400/230V, E.U. Electric
10 3/8 nut - flanged nylon lock nut FASN-38LNF
6 3/8 nut - flanged (regular) FASN-38RFL
12 3/8 x 1" bolt - flanged bolt FASB-38X1L
5 Cable tie - Reusable nylon 6" black DBKR-CTIE6
3 Cable tie mount - Adhesive mount DBKR-CTMA
2 3/8 x 2" bolt - flanged bolt FASB-38X2F
4 3/8 x 1 1/2" bolt - flanged bolt FASB-3815F
4 3/8 x 1 1/2" bolt - flanged bolt FASB-3815F
LMMN-BOX #16 (4-7.5kW, S1, 400V, E.U. Electric)
1 Electric - Control Panel w/controler - 4 to 7.5kW,Y-D,400V,3PH,S1(2020) ENGE-YD-S1-400V-CP
Control Panel Assembly (factory-assembled):
2 Electric – Safety switch for back cover w/ 1.6m wiring (LMMNv2, HD36v2) ENGE-SFTY-001
1 Electric - Remote control box clamping bracket (LM29v2, MN26v2, HD36) MILL-EUELEC-0012
1 Electric motor - Control panel bracket (CE) (LM29v2) LM29-E0003
4 M4 x 8mm screw N/A
2 M4 x 30mm screw N/A
2 M4 nut N/A
1 Power cable clamp N/A
Parts List: LM29V2-75KW-EU-400V (7.5 kW electric motor (S1) (400V, 3Phs) package)
EN–6
MILL-ELEC-S1-MANEN (2021-07-14).indd 6MILL-ELEC-S1-MANEN (2021-07-14).indd 6 2021-07-14 3:54:02 PM2021-07-14 3:54:02 PM

Parts List: LM29V2-75KW-EU-400V (7.5 kW electric motor (S1) (400V, 3Phs) package)
Qty. Description Norwood No.
1 Electric motor - Motor - 4kW S1 duty, 2800 RPM, 400V 50 HZ 3 PHASE (custom) ENGE-4KW-S1-400V
MN26V2-BOX #15C (E.U., 4kW, 400/230V, 3PH Electric) (12” x 12” x 9”) (- lbs)
1 Sheave - 4.6" sheave (LM29) (bushing MILL-BUSH38MM req'd) MILL-SHV46IN
1 Bushing - 28mm QD metric (for MILL-SHV46IN & MILL-SHV56IN sheaves) (HD36, LM29) MILL-BUSH28MM
1 Electric motor - 4kW mounting plate LMMN-4KW-BRKT
1 Manual - Electric Motor System (S1) (English)(LM29v2, MN26v2, HD36, HD38) MILL-ELEC-S1-MANEN
LMMNv2-Bag #X (Safety Switches Bag)
4 M5 x 14mm screw - hex socket screw FASS-M514S
2 Safety switch - Limit switch bandwheel cover (1NO/1NC)(LM29v2, MN26v2, OS23, O27, OS31) FRON-SFTY1
MILLV2-BAG #ELECT - 400/230V, E.U. Electric
10 3/8 nut - flanged nylon lock nut FASN-38LNF
6 3/8 nut - flanged (regular) FASN-38RFL
12 3/8 x 1" bolt - flanged bolt FASB-38X1L
5 Cable tie - Reusable nylon 6" black DBKR-CTIE6
3 Cable tie mount - Adhesive mount DBKR-CTMA
2 3/8 x 2" bolt - flanged bolt FASB-38X2F
4 3/8 x 1 1/2" bolt - flanged bolt FASB-3815F
4 3/8 x 1 1/2" bolt - flanged bolt FASB-3815F
LMMN-BOX #16 (4-7.5kW, S1, 400V, E.U. Electric)
1 Electric - Control Panel w/controler - 4 to 7.5kW,Y-D,400V,3PH,S1(2020) ENGE-YD-S1-400V-CP
Control Panel Assembly (factory-assembled):
2 Electric – Safety switch for back cover w/ 1.6m wiring (LMMNv2, HD36v2) ENGE-SFTY-001
1 Electric - Remote control box clamping bracket (LM29v2, MN26v2, HD36) MILL-EUELEC-0012
1 Electric motor - Control panel bracket (CE) (LM29v2) LM29-E0003
4 M4 x 8mm screw N/A
2 M4 x 30mm screw N/A
2 M4 nut N/A
1 Power cable clamp N/A
Parts List: MN26V2-004KW-EU-400V (4 kW electric motor (S1) (400V, 3 Phs)package)
EN–7
MILL-ELEC-S1-MANEN (2021-07-14).indd 7MILL-ELEC-S1-MANEN (2021-07-14).indd 7 2021-07-14 3:54:02 PM2021-07-14 3:54:02 PM

Technical Data
ELECTRICAL SYSTEM
Power HD36v2 & LM29v2: 400 v, 50 Hz, 3/N/PE, 7.5 kW 15 A
MN26v2: 400 V, 50 Hz, 3/N/PE, 4 kW 7.5 A
Protection class IP55
MOTOR SPECIFICATIONS
Weight 7.5kW: 55 kg
4kW: 36kg
Rotation speed 2945 rpm
Standard IEC
SOUND LEVELS
Sound Pressure in the Operator’s Area (1) 88.4 dB(A)
Sound Power (Estimated) (2) 109.4 dB(A)
Vibration Level (3) < 2.5 m/s2
Water Container 12 L (3.2 US gal)
For MN26v2-4kW
Attention! Through poor conditions of the electrical MAINS, short voltage drops can appear when starting
the EQUIPMENT. This can influence other equipment (eg. Blinking of a lamp). If the MAINS-IMPEDANCE
Zmax<0.411OHM, such disturbances are not expected. (In case of need, you may contact your local supply
authority for further information).
For LM29v2-7.5kW and HD36v2-7.5kW
Attention! Through poor conditions of the electrical MAINS, short voltage drops can appear when starting
the EQUIPMENT. This can influence other equipment (eg. Blinking of a lamp). If the MAINS-IMPEDANCE
Zmax<0.421OHM, such disturbances are not expected. (In case of need, you may contact your local supply
authority for further information).
MILL-ELEC-S1-MANEN (2021-07-14).indd 8MILL-ELEC-S1-MANEN (2021-07-14).indd 8 2021-07-14 3:54:03 PM2021-07-14 3:54:03 PM

The part #LM34-C0220-SPC has to be
installed as per the picture here using the
3/8” x 1.0” bolts and 3/8” nylon lock nut.
Then continue the assembly of your
Norwood sawmill as per the owners manual.
Installation Requirements
Electrical system providing a residual current
device with a maximum residual current of 0.03A
should be provided. Installation of over-voltage
protection is needed.
Steady state voltage: 0.9-1.1 of nominal voltage
(400V~).
Frequency: 0.99-1.01 of nominal frequency
continuously;
0.98-1.02 short time.
HVF: ≤0.02
Before assembly, inspect parts to detect any apparent
damage. If there is damaged or missing parts, inform
Norwood Sawmills immediately.
Note: these instructions are used to assemble the electric
package for your sawmill. Some parts and pictures might not
be identical to your sawmill but are similar.
Please use these instructions in conjunction with your
sawmill manual.
For LumberPro HD36v2 Owners — Before You Start!
One part called “Rear leg assembly (HD36) – Spacer”
#LM34-C0220-SPC of the 7.5kW-400v electric package has
to be installed in two locations during the assembly of your
LumberPro HD36 carriage. This part must be installed before
the step shown below, found under “Carriage Assembly” in
the LumberPro HD36v2 manual:
Install the left (186) and right (187) rear leg
assemblies, LOOSELY. DO NOT TIGHTEN
ANY BOLTS YET.
Use 3/8 x 3/4” flange bolts (33A). Finger
tight only.
See Trailer Assembly section if
assembling a sawmill with trailer
package.
EN–9
Assembly
MILL-ELEC-S1-MANEN (2021-07-14).indd 9MILL-ELEC-S1-MANEN (2021-07-14).indd 9 2021-07-14 3:54:03 PM2021-07-14 3:54:03 PM

For LumberPro HD36v2
Use the holes indicated here.
Secure the electric motor with the 3/8” x 1 ½”
bolts and 3/8” flanged nuts.
Install the electric motor on the sawhead
panel.
See hole locations pictured below.
Install the push handle onto the carriage
using the 3/8” x 3/4” carriage bolts and 3/8”
flanged Nyloc nuts.
EN–10
Motor Installation
MILL-ELEC-S1-MANEN (2021-07-14).indd 10MILL-ELEC-S1-MANEN (2021-07-14).indd 10 2021-07-14 3:54:03 PM2021-07-14 3:54:03 PM

For LumberMate LM29v2
Use the holes indicated here.
Secure the electric motor with the
3/8” x 1 ½” bolts and 3/8” flanged nuts.
Use the holes indicated here.
Secure the electric motor and plate with the
3/8” x 2” and 3/8” x 1 1/2” bolts and 3/8”
nuts.
For LumberPro MN26v2
Install the electric motor mounting plate.
Secure it with the 3/8” x 1 ½” bolts and 3/8”
flanged nuts.
EN–11
MILL-ELEC-S1-MANEN (2021-07-14).indd 11MILL-ELEC-S1-MANEN (2021-07-14).indd 11 2021-07-14 3:54:04 PM2021-07-14 3:54:04 PM

Install the sheave and secure it with the
bushing onto the motor shaft. Secure it using
the 3 bolts provided inside the box of the
bushing.
(Before installing the drive belt, refer to the
owner’s manual to install the Bandwheel and
tensioning system of your sawmill)
Install the drive belt over the drive
bandwheel.
Route the drive belt over the idler pulley,
then over the sheave.
Check belt alignment with the bandwheel,
idler pulley and sheave.
Make any slight adjustment if necessary.
EN–12
MILL-ELEC-S1-MANEN (2021-07-14).indd 12MILL-ELEC-S1-MANEN (2021-07-14).indd 12 2021-07-14 3:54:04 PM2021-07-14 3:54:04 PM

Secure the bracket with the 3/8” x 1” flanged
bolts and 3/8” nuts.
Install the control panel bracket on the non-
operator side of the MN26v2 and LM29v2
sawmill carriage. Secure the bracket with the
two 3/8” bolts previously removed from the
MN26 and LM29v2 carriage assembly.
For MN26v2 and LM29v2
Install the control panel bracket to the
control panel, secure with the four M10 bolts
previously removed from the panel.
EN–13
MILL-ELEC-S1-MANEN (2021-07-14).indd 13MILL-ELEC-S1-MANEN (2021-07-14).indd 13 2021-07-14 3:54:05 PM2021-07-14 3:54:05 PM

For HD36v2
Install the HD36v2 control panel to the non-
operator rear leg assembly, and secure it
with the clamps provided with the panel.
This is the MN26v2 and LM29v2 control
panel properly installed.
Note: Move the control panel as high as
possible.
EN–14
MILL-ELEC-S1-MANEN (2021-07-14).indd 14MILL-ELEC-S1-MANEN (2021-07-14).indd 14 2021-07-14 3:54:06 PM2021-07-14 3:54:06 PM

This is the controller panel properly installed.
Install the controller panel to the mounting
plate using the four #10 screws.
For All Models
Install the controller mounting plate bracket
to the push handle using the two clamps.
EN–15
MILL-ELEC-S1-MANEN (2021-07-14).indd 15MILL-ELEC-S1-MANEN (2021-07-14).indd 15 2021-07-14 3:54:07 PM2021-07-14 3:54:07 PM

Install the dead man’s switch to the push
handle using two M4x30m screws and M4
nuts.
EN–16
MILL-ELEC-S1-MANEN (2021-07-14).indd 16MILL-ELEC-S1-MANEN (2021-07-14).indd 16 2021-07-14 3:54:07 PM2021-07-14 3:54:07 PM