Nostalgia Electrics SCC-200 User manual

SNOW CONE CART™
Model # SCC-200
For Household Use Only!
Read These Instructions Before Using
This Unit!
SAVE THESE INSTRUCTIONS!

ENGLISH 1
IMPORTANT PRECAUTIONS
Appliance Specifications:
120 Volts
60 HZ
100 Watts
ETL Approved
Important Precautions to Remember:
A. NEVER immerse in water.
B. NEVER use near water.
C. NEVER use an abrasive sponge or cloth.
D. NEVER use a scouring pad on the unit.
E. NEVER leave unit unattended while in use.
F. NEVER try to force the cover in the locking mechanism.
G. Unplug unit from outlet when not in use and when cleaning.
H. DO NOT operate this appliance with a damaged cord or plug or in the event the
appliance ever malfunctions.
I. Keep out of reach of children.
J. This appliance is NOT A TOY.
K. This appliance is not intended for use by young children or infirm persons without
supervision.
L. Young children should be supervised to ensure that they do not play with the
appliance.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before operating this appliance.
2. DO NOT TOUCH hot surfaces. Keep hands away from blade mechanism. Use
handles or knobs.
3. To protect against electrical shock, do not immerse cord, plug or any part of this
unit in water or other liquids.
4. Close supervision is necessary when any appliance is used by or near children.
5. Unplug from outlet when not in use and before removing parts and before cleaning.
6. DO NOT operate any appliance with a damaged cord or plug or if the appliance has
been damaged in any manner. Return the appliance to the nearest repair shop for
examination or repair or send back to company as stated in this booklet in the
warranty.
7. The appliance manufacturer does not recommend the use of accessory
attachments. This may cause injuries.

ENGLISH 2
IMPORTANT SAFEGUARDS (Continued)
8. DO NOT use outdoors.
9. DO NOT let the cord hang over the edge of table or counter tops, or touch hot
surfaces.
10. DO NOT place on or near a hot gas or electric burner, or in a heated oven.
11. Extreme caution must be used when moving this appliance.
12. DO NOT use the appliance for other than its intended use.
13. A unit that is plugged into an outlet should not be left unattended.
14. Check ice hopper for presence of foreign objects prior to use.
15. Blades are extremely sharp. Use with extreme caution.
16. DO NOT place on or near a hot gas or electric burner, or in a heated oven.
17. Longer detachable power supply cords can be used if care is exercised in their use.
18. The marked electrical rating of an extension cord should be at least as great as the
electrical rating of the appliance.
19. This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electrical shock, this plug is intended to fit into a polarized outlet only one
way.
SAVE THESE INSTRUCTIONS!
INTRODUCTION
Thank you for purchasing the one-of-a-kind SNOW CONE CART™. This vintage looking
appliance beautifully resembles the carnival style vendors of the early 1900s. Though it
may be designed to look like a nostalgic cart of the past, The SNOW CONE CART™ is in
fact a technologically modern snow cone maker, and should be treated as such.
The SNOW CONE CART™ uses ice cubes from your freezer or icemaker to create:
Snow Cones
Slushies
Smoothies
Low Fat Snacks
The SNOW CONE CART™ is designed for indoor use and can be used in a number of
locations such as:
Family Rooms
Dorm Rooms
Offices
Club Houses
Now you can enjoy icy, cool snow cones to snack on when……
Watching TV or a Movie at Home
Throwing a Party
Listening to Music
Craving a Low fat Treat

ENGLISH 3
ASSEMBLY
After Taking the Unit Out of the Box:
Your SNOW CONE CART™ requires some assembly before first use. The Main Unit,
which includes the ice grinder, is already assembled. You will need to put together the cart
itself using the instructions that follow. Before first use, make sure to wipe clean the inside
of the Main Unit with a non-abrasive moist sponge, a non-abrasive towel, or a damp cloth
followed by a non-abrasive dry towel.
BREAKDOWN
Parts

ENGLISH 4
ASSEMBLY (Continued)
Screws, Studs, and Nuts
ASSEMBLY
1. Open the box and remove all parts including the Main Unit, Storage
Compartment, Wheels, Legs, and all other contents (including the Push Handle
and accessories).
2. Attach the Push Handle to the Storage Compartment using four of the #1 screws
(as shown below):
Main Unit
Base Support
Storage
Compartment
1
2
3
4
5
6
7
8

ENGLISH 5
ASSEMBLY (Continued)
3. Connect the Base Supports by screwing two of the #1 screws into the Cross Bar
(as shown below):
4. Connect the Leg Assembly by screwing four of the #3 studs from the Base
Support into the Leg Assembly (as shown below). Make sure to screw from the
Base Support into the Leg Assembly and not vice versa. Once the studs are
firmly screwed through, place the four #8 Nut Caps over the studs for cosmetic
purposes:
5. Now that the Leg Assembly and Base Support have been connected, use four of
the #2 screws to connect the Storage Compartment to the Base Support (as
shown below). Once you have successfully screwed the #2 screws through the
Storage Cabinet and into the Base Support, place the Bottom Plate underneath
the Storage Cabinet and attach it to the Base Support using four of the #1
screws:

ENGLISH 6
ASSEMBLY (Continued)
6. Attach the Wheels to the Base Support by using two of the #4 Wheel Rods.
Slide a #5 Lock Washer onto a Wheel Rod, and then push the Wheel Rod
through the holes in the Base Support. Make sure to place the two #6 Flat
Washers between the Base Support and the Wheels. Repeat on the other
wheel. Finally, place the two #7 Wheel Rod Caps on the outside of the screws
for cosmetic purposes (as shown below):
7. Place the Main Unit onto the Storage Compartment so that the two side holes
match up. Connect the Main Unit to the Storage Compartment using the two
included Lock Screws (D) as shown below:
8. Place the Clear Plastic Bowl into the top of the Main Unit and firmly secure the lid
into the bowl. Make sure that the end of the lid with the two tabs is properly
placed into the corresponding holes and the lid snap shuts. Please note that the
ice will not shave unless the lid is properly secured. Never force it down.
You are now ready to use your SNOW CONE CART™!
Helpful Hint: Use the black plastic adjusters on the bottom of the feet to properly level.

ENGLISH 7
USING YOUR SNOW CONE CART™
USING YOUR SNOW CONE CART™
First, find a stable surface near an electrical outlet before starting. (Make sure your cord is
away from any water source. If needed, it is acceptable to use an extension cord.)
1. Before plugging in your unit, add ice cubes by removing the clear lid from the
Main Unit of your SNOW CONE CART™. In order to do so, simply push the
release button on the lid, lift and remove. Once you have done this, plug in the
unit.
For Optimal Ice Shaving Results – Your ice cubes should sit a short while before putting
them in the shaving unit. If your ice has a frosty look, it is much too hard to shave. If your
ice sits long enough to look clear and it is wet to the touch, then it is ready to make your
SNOW CONE CART™ experience a fun one.
2. When ice cubes are ready, place cubes in the shaving unit while allowing enough
room for the lid to be placed back on the unit easily. Never force it shut.
3. Return the clear lid to the unit and turn the power button to the ON position. This
will activate the unit to begin shaving. Please note that the ice will not shave
unless the lid is properly secured.
4. Repeat steps 2 and 3 until you have shaved the amount of ice desired. Make
sure to unplug when you are finished.
5. Once you have the desired amount of ice, open the housing door on the Main
Unit to retrieve your ice and use the recipes on the next page to create your
favorite snow based treats!
REPLACING THE BLADE
Should the ability of your SNOW CONE CART™ to properly shave ice diminish after a
lengthy period of normal use, replace it with the included Replacement Blade and Tool.
Should you need additional blades, you can order directly from the manufacturer.
Please note the following steps for replacing the blade:
1. Remove the Ice Tray and insert the Disassembly Tool (N under PARTS) over the three
arms of the Ice Hopper.

ENGLISH 8
REPLACING THE BLADE (Continued)
When following the next three steps, use EXTREME CAUTION as the blade is very
sharp! Once the Ice Tray is removed, you are fully exposed to the blade inside!
2. Once the Disassembly Tool is properly inserted, twist counter-clockwise (as the arrow
shows) and lift the Ice Hopper out.
BLADE IS NOW COMPLETELY EXPOSED – USE CAUTION
3. Locate the two plastic clips on the Blade Assembly and use a spoon and your thumb to
press the clips inward and lift out the Blade Assembly.
4. Twist off the Blade Retainer Nut, and using extreme caution, remove the Blade Cartridge
from the Assembly. Insert the replacement Blade Cartridge, and reverse the above
steps to reassemble.
5. After reversing all steps, make sure to lock with the tool.

ENGLISH 9
CLEANING
1. Make sure the unit is unplugged before cleaning.
2. Open the housing door to clean and dry inside of unit using a slightly damp, non-
abrasive sponger or non-abrasive towel.
3. Also use a slightly damp, non-abrasive sponge or non-abrasive towel to wipe
clean outside of unit, then wipe with a non-abrasive dry towel to dry.
4. The shaving unit and clear lid are dishwasher safe. To take out the shaving unit,
simply turn the white top in a counter-clockwise direction and it will unscrew,
unlocking the top.
IMPORTANT: The blade is very sharp. Use EXTREME CAUTION when handling.
RECIPES
Your SINOW CONE CART™ makes light and fluffy mounds of ice that can be used to
make:
SNOW CONES – Add your favorite syrup flavor. Add more than one flavor to increase the
fun and vary the flavor by creating Rainbow Snow Cones.
SLUSH DRINKS – By filling a glass with freshly shaved ice and adding your favorite soft
drink or flavored tea or fruit juices.
FRUITY SLUSH – By filling a serving cup with freshly shaved ice, adding flavored syrup
and topping with chopped fruit of your choice.
YOGURT SNOW – By pre-freezing your favorite flavored yogurt in ice cube trays, you can
use your SINGLE CONE VINTAGE SNOW CONE MAKER™ to shave the yogurt cubes
and make a refreshing, healthy treat. Add flavored syrup for even more flavor.
SNOW SMOOTHIES – By freezing ½cup of milk in ice cube trays, you can use your
SINGLE CONE VINTAGE SNOW CONE MAKER™ to shave the cubes. Place the shaved
cubes and fresh strawberries or your choice of fruit in a blender. Add 1/4 cup of sugar for
sweetness, then blend until smooth to your desired consistency.
JUICY TREATS – By freezing your favorite juice in ice cube trays, you can use your
SINGLE CONE VINTAGE SNOW CONE MAKER™ to shave the cubes to create a healthy,
juicy treat.
Use your imagination with different fruits, syrups, sodas, teas and juices to create any
number of refreshing, icy, healthy, low fat treats, drinks, and desserts that will delight kids
of any age