Notifier IFS-2600 Technical manual

ECN11
-
00
6
1
1
1. Product Overview
IFS-2600 Termination Board (TB) is the main termination board, where connections from all other devices in the
panel and thefield are terminated. The Power Supply Interface board (PSI) is mounted directly on top of the spacers
provided in the Termination Board which is available as a separate kit (#ASY-02-021). Both these boards are
mounted on a metal work chassis, which in turn is assembled in the IFS-2600 base panel. A power supply unit (PSU)
is mountedto the chassis, which powers the panel.
Figure 1, IFS-2600 Chassis
This is the IFS-2600 CHS chassis (#MW-02-012) onto which Termination board (#PCA-01-048) will be
assembled.
2. Installation
WARNING:
Installation should be performed by competent persons in accordance with the
relevant standards as required for the installation. Honeywell Ltd accepts absolutely no liability
for the suitability, settings or connections done within an installation.
1. Attach the male end of four M3x20 M/F tapped spacers (#11164) to the four slots provided on termination
board and secure it using four M3 flanged nuts (#10313) as shown in Figure 2.
Figure 2, IFS-2600 Termination Board (NI-2025-01 PCB)
9 Columbia Way
Baulkham Hills, NSW 2153
PH 02-9894-1444 • FAX [phone]
www.notifier.com.au
Notifier IFS-2600 Termination Board (TB)
Product Installation Document
DOC
-
03
-
037
ECN11
-
00
61
21
/0
9
/2011
Rev:
1.0
2
IFS-2600 Chassis
(#MW-02-012)
Studs to secure
Termination
Board
M3 Flanged Nuts (#10313)
to Male end of
Spacer (#11164)

ECN11
-
00
6
1
2
2. Attach the Termination board (#PCA-01-048) to the four Studs on the IFS-2600 chassis and secure it using
four Philips head sems screws (#2316) as shown in figure 3.
Figure 3, Termination Board Secured to IFS-2600 Chassis
3. Place the Power Supply Interface (PSI) board (#PCA-01-045) on the spacers (provided on the termination
board) and secure it using four Philips head sems screws (#2316) as shown in figure 4.
Note: This assembly is termed as Top Hat Assembly, which will be secured to the Base panel.
Figure 4, PSI Board attached to Termination Board
4. If the IFS-2600 Top Hat Assembly was removed from the panel, re-attach it to the top location of IFS-2600
Base panel and secure it using four M4 flanged nuts (GEN-01-008) as shown in figure 5.
Figure 5, IFS-2600 TB on Chassis installed in Base Panel

ECN11
-
00
6
1
3
Figure 6, Termination Board, PSI & PSU Connection Diagram
3. Components
The IFS-2600 TB kit assembly contains the following components, as outlined in Table 1.
Part No. Description Qty
2316 M3 x 8 Philips Head Sems Screws 8
10313 M3 Flanged Nuts 4
11164 M3 x 20 M/F Hexagonal Tapped Spacer 4
11877 Cable - 4 way Power PSI for IFS-2600 – 150mm (DWG0058) 1
11878 PSI-FIM Ribbon Cable10 Way – 150mm (DWG0059) 1
CA-01-005 24V Cable – PSI to PSU – 4 Way, Red+Black 550mm (DWG0304) 1
PCA-01-048 Termination Board to Suit IFS-2600, NI-2025-01 PCB 1
Table 1: Components
4. Supplemental Documentation
For
information
on... Refer to... Part No.
IFS-2600 TB IFS-2600 Installation, Programming & Operations Manual DOC-01-009
Table 2: Supplemental Documentation