Nouveau 229346 User manual

IMPORTANT INSTALLATION INSTRUCTIONS SHALL BE READ BEFORE THE
USE OF THIS PRODUCT
SAVE THESE INSTRUCTIONS AFTER INSTALLATION FOR FUTURE REFERENCE
WARNING
WARRANTY
The installation should be carried out by at least two adults. When assembling the upper parts, please use a ladder.
The setscrews supplied are intended for concrete wall. If you intend to attach the awning to other materials
(e.g. wood), other fasteners are required accordingly. Please make sure the fasteners for other materials
installation have the same or higher strength in comparison to the provided expansion bolts for
installation surfaces.
1. Never use the awning during heavy rain or storm. Please do not extend the awning when wind is above
Beaufort Scale 5. Otherwise, the awning may be damaged and then cause risk for users.
2. Keep the fabric away from fire and flammable objects.
3. Do not put any heavy objects on the top of fabric while the awning is extended.
4. Check the awning once every month to make sure all bolts and nuts are tightened. Should you find any loose
bolts, tighten them up immediately.
5. Do not operate the awning if any cleaning or maintenance is performed on the windows or doors nearby.
6. Do strap both parts of the arm, or extend the awning fully until the internal springs are completely free of
tension before you assemble, adjust or clean the jointed arm.
7. This awning should be installed at the height over 2.5M away from floor or ground.
This awning is warranted for 2 years with proper operation and 2 cycles a day.
8. Make sure there is enough space for awning extension before installation.
CARE AND MAINTENANCE
FRAME
Cleaning: Use a mild detergent and warm water on the frames. Do not use abrasive materials, cleansers,
chemicals, bleach or solvents on frames. Rinse with clean water. Dry thoroughly.
Maintenance: Frame finishes may be maintained by applying a quality auto wax after each cleaning. For best
results, always cover awning when not in use. We recommend plastic cover. Always clean and dry frames
thoroughly before covering.
FABRIC
Cleaning: Wipe up minor spots with mild soap and a damp cloth. It is sufficient to brush off the dirt on the
curtain in most cases.
Maintenance: Dry the fabric in the extended position when it is wet as soon as possible. The best way to
maintain the look of your fabric is to cover them when not in use.
PACKAGE
This awing is packed in double corrugated carton box with inner poly bag. The spare parts are packed in a
separate inner box or poly bag inside the master carton. If the carton is broken or damaged, identify all parts
against the parts list. Do not attempt assembly if any parts are missing or damaged.
INSTRUCTION FOR MANUAL
AWNING 3X2M

Mark Top-of-bracket Line
Measure The Distance Of Two Wall Bracket
Installation of bracket
1. Identify all parts packed in carton
against the parts list. Remove all
protective material. Place Parts on
non-abrasive surface to avoid scratches.
Do not attempt assembly if any parts are
missing or damaged.
2. Find an appropriate place over 2.5m to
the floor or ground for assembling the
awning on the wall and place a mark.
3. Draw a line on the wall with a ruler
according to the mark. It will be the
top-of-bracket line (the line must be
horizontal). This is to say, this line might
not be parallel with other structural lines,
such as siding, etc.
4. Locate where wall brackets are to be
installed and mark. The brackets must be
assembled onto the wall vertically.
Parts List
Warning! Make sure you are the using all of hardware included in the package. Not using any
pieces may weaken the structure of the awning and can be a potential safety hazard.
of the
A 1PC
B1
B2
2PCS
2PCS
1PC
4SETS
2SETS
C
D
E
Either B1 or B2 is
workable in following
steps.

5. Drill two holes according to the mark for each bracket. The diameter of the drill head should be
0.55 inch (14mm). The hole must be longer than the bolt. With the help of hammer, insert the setscrew into the
drilled hole except the end part with nut. Fix the bracket to the wall and tighten the nut.
Installation of Awning
2 adults are needed to handle this operation. With help, lift awning to the brackets on wall and slip torsion bar into
brackets as shown in the following Fig..If torsion bar can not be easily slipped into the bracket, lift the front profile
slightly. If it still does not work, loosen nuts (7) on the bracket to align the torsion bar with bracket. Finally,
tighten all bolts securely.
Install On Wall
B1
B2
E
C
D
D
Following steps,
take B1 as the example.

Roller Bracket
Torsion Bar
Left Arm
Wall Bracket
Right Arm
Front bar
Hand Hook
Valance
Arm Base
Gear Box
Fabric
Arm
Locking Nuts
Jack Bolt
Retract
Extend
OPERATION
1. Turn the hand hook to retract or extend the awning as you require.
Warning: Stop retracting the curtain with excessive force if already fully
retracted. The wrong operation may cause damage to the awning.
2. Loosen the locking nuts. Then, turn the jack bolt to adjust pitch from 12 to 45.
3. Adjust the arm until the front bar is on horizontal level.
4. Tighten the locking nuts.
Enjoy the delightful outdoor living with the awning now!