Novusun CNC NC200 User manual

百年品质，值得信赖 —— 您的产品名称
Manual
MACH3 LPT port USB Card
NC200

M请在这里输入您的公司名称或产品名称
Manual of NC200
Manual of NC200
Contects
Chapter 1.Introduction..................................................................................................................................- 1 -
1.1 Product Introduction ..............................................................................................................................- 1 -
1.2 Products specification ............................................................................................................................- 1 -
1.3 Products Appearance and size................................................................................................................- 2 -
1.4 substantival explanation.........................................................................................................................- 3 -
1.5 Noting and Waring .................................................................................................................................- 4 -
Chapter 2.Connection ...................................................................................................................................- 5 -
2.1 Product connection define and method..................................................................................................- 5 -
Chapter 3.Software Installation ..................................................................................................................- 10 -
3.1 MACH3 Install ....................................................................................................................................- 10 -
3.2 NC200 Plug-in installation ..................................................................................................................- 13 -
Chapter 4.Setting of software .....................................................................................................................- 14 -
4.1 Open software ......................................................................................................................................- 14 -
4.2 Software Common settings..................................................................................................................- 15 -
Chapter 5.Using of software.......................................................................................................................- 22 -
5.1 Set Machine Coordinate system...........................................................................................................- 22 -
5.2 Set workpiece coordinate system.........................................................................................................- 24 -
5.3 Open G code file and run .....................................................................................................................- 26 -
Chapter 6.Question & Answer....................................................................................................................- 28 -
6.1 Q&A for Hardware ..............................................................................................................................- 28 -
6.2 Q&A for Software................................................................................................................................- 28 -
Chapter 7.Contract us .................................................................................................................................- 29 -
www.nvcnc.net

Chapter1 Introduction
Manual of NC200
- 1 -
Chapter 1. Introduction
1.1 Product Introduction
Novusun CNC has engaged in the Numerical control industry for 7 years, specialized in
the research, development and production of various CNC controller systems with high quality
and high reliability. We produce the Brushless DC motor, Stepper motor driver, and also 1 to 6
aixs CNC motion controllers.。
NC200 is the 4 axis motion controller we spend 4 years to design.
NC200 support Mach3 software and serial port MPG, through USB to communicate
with computer.
NC200 motion controller adopts the ARM design framework. The ARM design
includes communication,codeanalytic, underlying algorithm and pulse gerneration. Rational
design, reliablecontrol, convenient operation.
This manual introduces operation, connection and usage schedule of our professional
motion controller for engraving machine. Through a lot of the drawing the users can learn
quickly how to use this motion controller.
1.2 Products specification
Support USB;
5 ports input interface for ordinary digital data；
3 ports output interface for ordinary digital data；
1 port 0-10V spindle speed analog output interface(can change to PWM output)；
www.nvcnc.net

Chapter1 Introduction
Manual of NC200
- 2 -
can support 4 axis stepper systems,200KHz pulse output for every axis；
ARM motion control chip；
Compatible with MPG input, support the digital display MPG from our company。
1.3 Products Appearance and size
NC200 motion controller is with the plastic shell structure. The controller appearance as
the Figure 1-1 show:
The products overall size is 56.8mm*54.1mm*22mm；
Figure1-1. NC200 front appearance and size
www.nvcnc.net

Chapter1 Introduction
Manual of NC200
- 3 -
1.4 substantival explanation
When operate the NC200,where will be a lot of English abbreviation,now we list all of
them for your kindly references:
FRO:Feedingadjust:During the operating process,the F value already set,and need to
adjust the current feeding speed, then we can adjust FRO value to realize it.
SRO: Spindle speed adjust: During the operating process, the S value already set, and need
to adjust the current spindle speed, then we can adjust SRO value to realize it :
Current Speed S#=setting S*SRO.
SRJ:speed adjust manually
During the operating process,as the manual speed already set,and we need to adjust the
current speed,and impossible to fix the value during it is working,then we can revise the SRJ
value to realize it.
Current manual speed FS#=Setting manual speed*SRJ.
F:Feedingspeed,the unit is mm/min.For example F=200,means every minute feeding
2000mm.
S: Spindle Speed. Unit is rad/min.For example S=20000,means 20000 revolution/Minute.
X axis Coordinate
Y axis Coordinate
Z axis Coordinate
A axis Coordinate
www.nvcnc.net

Chapter1 Introduction
Manual of NC200
- 4 -
1.5 Noting and Waring
Free from exposure to the electronics without waterproof
function.Please environment as dry as possible. This is the icon.
Wiring warning, the IO input terminal of this equipment support the
equipment with source switch (such as Inductive proximity switch.)When using
such kind of switch, attention please: avoid the +terminal and –terminal of
power supply to connect with GND.This equipment’s analogy quantity
output terminal of spindlecontrolalos have a certain load capacity. Please avoid
this terminal connect with GND.in case that the interior components and parts be
brokendown.
Operation warning, Please do the security measures well when
connecting with the machine tools.The ESTOP, limit and other things must be
perfected.When comes across the emergancy, please press the ESTOP key at once
or cut off the power directly, thus avoiding the equipment damage and casualty.
High voltage danger, the primary device is 18-32VDC power
supply.Voltage equipment.Pls pay attention to the electricity, safety when conducting
the operation
www.nvcnc.net

Chapter2 Connection
Manual of NC200
- 5 -
Chapter 2. Connection
2.1 Product connection define and method
Figure2-1. Product wiring section and interface summary
As the Figure 2-1 showed,the connection of the controller includes USB connection
interface, MPG interface and LPT controller port. Now we descript them in details as below.
2.2.1 LPT Controller interface
As Figure 2-1 showed,No.1 is LPT Controller interface. In the first row, from right to left,
it's PIN1 to PIN13; in the second row, from right to left, it's PIN14-PIN25.
PIN1-PIN9,PIN14,PIN16,PIN17 are output PINs, which can be set as PWM, usual output and
www.nvcnc.net

Chapter2 Connection
Manual of NC200
- 6 -
stepper motor control port. and PIN10-PIN13,PIN15 are input PINs, which can be set as probe,
limit, estop and home. See as table 2-1.
Figure2-2. sequence of LPT port
No. INPUT & OUTPUT Note
1 OUTPUT PORT Can be set as usual output\stepper
motor controller port and spindle
PWM output
2 OUTPUT PORT
3 OUTPUT PORT
4 OUTPUT PORT
5 OUTPUT PORT
6 OUTPUT PORT
7 OUTPUT PORT
www.nvcnc.net

Chapter2 Connection
Manual of NC200
- 7 -
8 OUTPUT PORT
9 OUTPUT PORT
10 INPUT PORT Can be set as limit/estop/probe/home
11 INPUT PORT
12 INPUT PORT
13 INPUT PORT
14 OUTPUT PORT Can be set as usual output\stepper
motor controller port and spindle
PWM output
15 INPUT PORT Can be set as limit\estop\probe\home
16 OUTPUT PORT Can be set as usual output\stepper
motor controller port and spindle
PWM output
17 OUTPUT PORT
18-25 GND Ground
Table 2-1. Stepper driver control interface define
NC200 can replace computer's LPT port, and performs better than computer's LPT port. This port
connect to stepper driver board see as figure 2-3.
www.nvcnc.net

Chapter2 Connection
Manual of NC200
- 8 -
Figure2-3. Connect with Stepper driver board
2.2.2 MPG connection
As shown in Figure 2-2 marked 2 of the location of the serial port MPG, the port type is
RJ45, that is, the common standard network interface. Serial pulse generator pulse generator is the
standard pulse generator, the axis of choice, such as the choice of power through the serial port and
host interaction. Serial port hand pin, pin label reference figure 2-4, from left to right in order
PIN1-PIN8. Serial port hand pulse pin definition reference table 2-2. serial port manual pulse
using method reference serial port manual pulse user manual.
www.nvcnc.net

Chapter2 Connection
Manual of NC200
- 9 -
Figure2-4. Pins Number of MPG
No. Mark Definition
1 GND GND of MPG
2 RXD Serial input communication port
3 TXD Serial output communication port
4 +5V 5V power port
5 FHA+ A+ of MPG
6 FHA- A- of MPG
7 FHB+ B+ of MPG
8 FHB- B- of MPG
2.2.3 USB Port
As the Figure 2-1 show,The marked No. 3 port is USB communication port, NC200
communicate with mach 3 through it.
www.nvcnc.net

Chapter3 Software Installation
Manual of NC200
- 10 -
Chapter 3. Software Installation
3.1 MACH3 Install
MACH3 installation, registration, and USB plug-ins. See as Figure 3-1
Figure3-1. MACH3 soft installation
First run the installation Mach3Version3.043.066 .Into the first
page. See as Figure 3-2.
www.nvcnc.net

Chapter3 Software Installation
Manual of NC200
- 11 -
Figure3-2. MACH3 installation process 1
Click Next and then enter the page shown in Figure 3-3
Figure3-3. installation process 2
Select I agree and click Next，See as Figure 3-4.
www.nvcnc.net

Chapter3 Software Installation
Manual of NC200
- 12 -
Figure3-4. MACH3 installation process 3
Select the installation path, click Next (it can be installed on any disk, and recommended
to install the C drive or the D drive) See as Figure 3-5
Figure3-5. MACH3 installation process 4
Click Next until completion. Then restart the computer.
www.nvcnc.net

Chapter3 Software Installation
Manual of NC200
- 13 -
3.2 NC200 Plug-in installation
Copy the file NC200.dll to X:\Mach3\PlugIns，X is the disk where the
soft is installed.
www.nvcnc.net

Chapter4 Setting of software
Manual of NC200
- 14 -
Chapter 4. Setting of software
4.1 Open software
Double-click the mach3mill 。
Enter mach3 software. Pop-up the plug-in dialog box. See as Figure 4-1.
Figure4-1. Plugin selection dialog
Choose our plugin NC200_Novusun-PlugIn---Ver- 。 2.0a Then press OK. If you do not want
to the dialog box appear again next time, you can select Don’t ask me this again.If connect
successfully,Status bar will show “NC200 device is connected to your computer”. See as
Figure4-2.
www.nvcnc.net

Chapter4 Setting of software
Manual of NC200
- 15 -
Figure4-2. connect successfully
4.2 Software Common settings
4.2.1 Check NC200 plugin
Click config plugins to input PluginConfig,you can seeNC200. See as Figure4-4.
Figure4-3. Input Config plugins
www.nvcnc.net

Chapter4 Setting of software
Manual of NC200
- 16 -
Figure4-4. MVUM Plugin
4.2.2 Motor operating parameters setting
Figure4-5. Motor operating parameter setting menu entry
See as Figure 4-5.From submenu “motor tuning” of the menu “config” into the motor
parameter settings dialog. See as Figure 4-6
www.nvcnc.net

Chapter4 Setting of software
Manual of NC200
- 17 -
Figure4-6. Motor operating parameter settings dialog
The parameters are defined as follows:
S： teps per Pulse equivalent ,it is number of pulses required with axial movement 1mm, This
can be calculated by lead screw pitch and motor drive segment. Such as pitch 2.5mm,2-phase
motor 8 segments, Calculation method is 。 8*200/2.5=640
：
Velocity The speed is the axial velocity, Units ， is mm/s Recommended settings 1500.
：
Acceleration Units ， is mm/s2 Recommended settings 200.
：
Step Pulse Step Pulse Cannot be set, it’s 2.5us in default.
：
Dir Pulse . Dir Pulse Cannot be set, it’s 2.5us in default.
Attention: The parameters for each axis is not necessarily the same，To select the axis,
and then set parameters. You should click “SAVE AXIS SETTINGS” After setting.
4.2.3 Port Settings
www.nvcnc.net

Chapter4 Setting of software
Manual of NC200
- 18 -
Figure4-7. Port setting intry
See as Figure 4- ， 7 Click the sub-menu “ports and pins” of menu “Config” into Port Settings
dialog box.
Figure4-8. Pin&Port Dialog
The sub-pages you need to set include “Motor Outputs”, “Input Signals”, “Output Signals”
and “Spindle Setup”.First Click to enter “Motor Outputs”. This page is to select the stepper motor
control pin. See as Figure4-9. Here based on the actual customer application board to set the pin
definition, here we take NV8727T4 as an example, the XYZA 4 axis pulse and direction signals
in turn PIN2, PIN3, PIN4, PIN5, PIN6, PIN7, PIN8, PIN9.
www.nvcnc.net