NSB FAN Jaya Deluxe User manual

INSTRUCTION MANUAL
CEILING FAN
Jaya Deluxe
The official website : https://www.nsb.com.my

1
SAFETY PRECAUTION
IMPORTAN: PLEASE READ BEFORE INSTALLATION
1. Installation must be carried out by a qualified wiring installer
2. Turn off the electrical mains at the circuit breaker fuse box
3. Use power supply 220-240V/50Hz.
4. The ceiling mounting must be able to with hold a min of 16kg.
5. Install ceiling fan blade more than 2.3 M above floor.
6. Do not place any objects in the path of the blades.
7. When all electrical connection is done, store all wire neatly.
8. Make sure that all screws and connection are tightly screwed and secured.
9. This appliance is not intended for use by persons (including children) with Reduced physi-
cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsi-
ble for their safety. Children should be supervised to ensure that they do not play with the
appliance.
10. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
11. An all‐pole disconnection must be incorporated in the fixed wiring in accordance with
the wiring rules, a all‐pole disconnection incorporated in the fixed wiring is to be provided.
12. The replacement of parts of the safety suspension system device shall be performedby
the manufacturer, its service agent or suitably qualified persons.
13. The fixing means for attachment to the ceiling such as hooks or other devices shall be
fied with a sufficient strength to withstand 4 times the weight of the ceiling fan.
15. The mounting of the suspension system shall be performed by the manufacturer, its
service agent or suitably qualified persons.
16. Disconnection must be incorporated in the fixed wiring in accordance with the wiring rules

2
PARTS & ACCESSORIES
6
9
8
7
10
11
1 Canopy × 1
2 Coupiling cover × 1
3 Downrod × 1
4 Motor × 1
5 Blades × 5
6 Nut × 3
7 Flat washer × 11
8 Blade screws
× 11
9 Balancing kits × 1set
10 Remote × 1
11 Receiver × 1
Fig.1
1
4
5
2
3

3
FAN INSTALLATION INSTRUCTION
Coupling cover
Canopy
IMPORTANT: SWITCH OFF THE ELECTRICAL MAINS THE CIRCUIT BREAKER FUSE BOX.
Follow the steps below to hang your fan properly.
Fig.1
Fig.3 Fig.4
Fig.2
Downrod
Nut
Cotter pin
Spring Washer
Flat Washer
Bolt
Plastic plug
Plastic Plug
Safety Cable
Bolt
2. Assemble the plastic plug into the motor shaft, Carefully feed the fan wires up through the
plastic plug.(Fig.2)
3. Insert the canopy and coupling cover through the down rod.(Fig.3)
4. Place the lead wire and safety cable thorgh the top of downrod. Insert the downrod
into plastic and aligning holes to the holes of shaft and plug. Tighten the downrod
to motor with the previous bolt、washer、nut and contter pin.(Fig.4)
down rod

4
FAN MOUNTING
Safety Cable
Bolt
Nut
R-pin
Spring Washer
Ceiling
Hook
a
WARNING
!
Screw Screw
Safety
Cable
1 2 3
1).Remove the safety Cable Screw from the downrod bracket.
2).Arrange and tie the Safety Cable as above image
labelled with 2.
Safety Cable must be fixed correctly.
May cause injury if ceiling fan drops.
Install Safety Cable
rubber
wheel
3).Firmly screw the Safety Cable onto the downrod.
5. “J” Hook mounted ，When mounting the fan, ensure that the safety cable is loop across the “J” hook.
6. “U” Hook mounted Remove the bolt, stop pin, nut, washer and rubber pulley from the downrod.
Place the rubber pulley onto “U” hook and fix back the bolt, stop pin, nut and washer.
Fig.5 Fig.6
Fig.7

5
Ceiling
Black(AC IN N)
Red(AC IN L)
ELECTRICAL CONNECTION
Warning : To avoid possible electric shock, turn off the electricity at the main fuse
box or circuit panel before the fan electrical connection. For safety and best
installation result please consult a qualified electrician.
7. Connect wires: As shown in the below (Fig.8)
1) Connect the Black wire from motor to the Black "For Light L" wire from Receiver
with a wire nut.
2) Connect the Blue wire from motor to the Blue "For Light N" wire from Receiver
with a quick connector.
3) Connect the Pink wire from motor to the Pink "TO MOTOR V " wire from Receiver
with a quick connector.
4) Connect the Red wire from motor to the Red "TO MOTOR U " wire from Receiver
with a quick connector.
5) Connect the Grey wire from motor to the Grey "TO MOTOR W " wire from
Receiver with a quick connector.
6) The electric wire(hot) the Red "AC in L" wire from Receiver with a wire nut.
7) The electric wire (neutral) the Black "AC in N" wire from Receiver with a wire nut.
8) The ground wire from the Hanger Ball and the green ground wire from the
Hanger Bracket with a wire nut. (Make sure all of wire nuts are connected firmly.)
8. When the connection is completed, raise the top canopy and tighten it with the
screw attached, Tighten the Set Screw of the Coupling cover.
quick connector
Fig.8
Screw
Screw

6
BLADE INSTALLTION
8. Insert the screws and flat washer through the motor blade holder then secure the
blade to the motor by tightening the 2 screws.
9. Repeat this process to install the other blades to the motor.
Blade
Screw
Flat Washer

7
Due to fan’s natural movement, connections may get loose after a period of usage.
To ensure a proper and safety usage, We are highly recommended to inspect and
tighten all connections every 6 months.
CLEANING
Clean your fan periodically to prolong its new appearance. Basic cleaning procedures are as
follows:
1. Use only lukewarm water. Do not use detergent, corrosive or acidic solution.
2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will
scratches the surface.
3. Apply a thin coat of furniture polish to the wooden blades will protect and enhance the
appearance.
4. To cover small scratches, apply a light coat of shoe polish over it.
5. There is no need to lubricant the fan.
MAINTENANCE
TROUBLESHOOTING
Check on the following before lodging a service report.
SYMPTOM
PROBLEM
SOLUTION
Fan not moving
• Main cables not connected
• Wire connection loose
Fan noisy
Remote control
Not working
• Housing screws are loose
• Wire and nut connections rattles
against each other.
• Canopy touches the ceiling.
• Tighten all screws
• Separate and store neatly the
wire connections from the nut.
• Check to ensure the canopy is
not touching or too close to the
Ceiling.
• Check main and branch
circuit breakers or fuse.
• Check the line wires connec-
tions to the fan and switch
housing.
• Remote and receiver code different
• Battery not installed
• Weak battery
• Check that the codes to ensure
exactly the same.
• Install the remote control
battery
The official website : https://www.nsb.com.my