NSB FAN TEEGA User manual

Instruction
Manual
MODEL: TEEGA

1
Tables of Contents
Item
Safety Precaution
IMPORTANT: PLEASE READ BEFORE INSTALLATION
1. Installation must be carried out by a qualified wiring installer.
2. Turn off the electrical mains at the circuit breaker fuse box.
3. Do not use power supply other than 240V / 50Hz.
4. The appliance must be permanently connected to the electricity supply through a
double pole switch having contact separation of at lease 3 mm in all poles.
5. Do not connect ceiling fan to an dimmer switch or regulator.
6. When mounting the fan, ensure that the safety wire is loop across the ceiling
mounting hole.
7. The ceiling fan mounting hook must be able to with joint hold a min. weight of 35
pounds.
8. The ceiling fan must be mounted at a min. height of 8.2 feet / 2.5m of clearance
from the floor and 3 feet / 1m from the wall to the blade.
9. Do not install at areas / place near /at
a) Chemicals and alkali
b) Flammable areas such as gas cooker
c) Oily places
d) Wet and high humidity area example a shower area
e) High vibration / impact and continuously expose to direct wind
10. Do not place any objects in the path of the blades.
11. When all electrical connections are done, store all wires neatly.
12. Make sure that screws and connection are tighten till snug.
Warning
This product is design to use only those parts supplied with this product and / or
accessories designated specifically for use with this product. Using parts and / or
accessories not designated for use with this product could result in personal injury or
property damage.
Page NO.
1.
Safety Precautions.......................................................................................................
2. Parts & Accessories.....................................................................................................
3.
Installation Instructions..................................................................................................3-5
a. Fan Mounting..................................................................................................
b.
. Blades.................................................................................................................4
c. Wiring Connection..............................................................................................5
4.
Power Supply Connection............................................................................................6-7
5. Circuit Diagram..........................................................................................................
6. Technical Specifications..............................................................................................
7.
Maintenance................................................................................................................11
1
2
...3
..8
..9

Item
1. Canopy 1
2. Dow Rod 1
3. Down rod Jointer Cover 1
4. Blade 5
5. Fan Host Component 1
Receiver Transmitter
Note:
The Illustrations in this manual are for explanation purposes only and may differ from
the actual unit. It is subjected to change without prior notice for further improvements.
Parts & Accessories
Qty
2
1
2
3 4
5
6
1H 4H 8H
F/R
Canopy
Down Rod
Down rod Jointer Cover
Blade
Fan Host Component

Step 2- Remove the Fan Host Ring Cover.
Installation Instructions
3
IMPORTANT: SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER
FUSE BOX.
Step 1- Tighten the Ceiling Canopy Top Cover Component, Sealed Pads and Hanger
Bracket with screws provided.

Installation Instructions
4
Step 3- Tighten the blades with screws provided. Each blade uses 3 pieces of screws.
Ensure the screws (9 pcs) for securing the blades are tightly screwed.
Step 4- Fix back the Fan Host Ring Cover.

5
Installation Instructions
Step 5- Connect wiring as show.
Step 6- Tighten the ceiling canopy component with screws provided.

6
1
2 F/R
3 4
5
6
1H 4H 8H
Remote Control
- Turn the fan on/off
- 1 for low speed,
6 for high speed
- Controls the fan direction, forward or reversed
- Turn on the light
- Turn off the light
- Fan stop after 1hr
- Fan stop after 4hr
- Fan stop after 8hr
1-6
F/R
1H
4H
8H
Insert 2x1.5V AAA battery (provided) into the transmitter.
Function Transmitter
1.5V AAA
1.5V AAA

7
Power Supply Connection
IMPORTANT: DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO
DIMMER SWITCH OR WALL REGULATOR.

8
Circuit Diagram
Maintenance
Due to the fan’s natural movement, connections may get loose after a period of usage.
To ensure a proper and safety usage, it is highly recommended to inspect and tighten
all connections every 6 months.
Cleaning
Cleaning your fan periodically will prolong its new appearance. Basic cleaning
procedures are as follows:
1. Use only water. Don't use detergent, corrosive of acidic solution.
2. Use only soft cloth to clean the fan.
3. To cover small scratches, apply a light coat of shoe polish over if.
4. There is no need to give lubricant oil on fan spare part.
L
NBLUE NEUTRAL
RECEIVER
MOTOR
BROWN LIVE
BLUE
WHITE
BLUE
WHITE
YELLOW/GLEEN
YELLOW/GLEEN
RED
PINK
GRAY
RED
PINK
GRAY

9
Technical Specifications
Model
No. of Blades
Voltage
Motor
Teega
3
240V / 50Hz
DC
More than 1M
More than 2.5M

10
Balancing
PREFACE
Sometimes, your ceiling fan have
wobbling problems when operating
due to irregularity in the blades of
the blade holders Also, improper
assembly in the mounting system
or crooked bearing may cause
some additional problems. This
balancing kit can be used to fix
wobbling problems.
DYNAMIC BLADE BALANCING KIT FOR CEILING FANS
DYNAMIC BLADE BALANCING KIT
1. Make sure that all blades are firmly screwed into the blade holder.
2. Make sure that all blade holders are firmly secured to the motor housing and check
that the pitch of blade holders are all the same.
3. By looking up at the fan from below, check and confirm that none of the blade holders
are bent and that none of the blades are out of position. A correction can be made by
Bending the blade holder back into position gently.
4. Use a measuring tape to check the blade tracking. Put the yard stick up against the
ceiling vertically and against the outside leading edge of a blade. Note the distance of
the ceiling. Turn the blades slowly and carefully by hand to check the remaining
blades. If the blades not in alignment, the blade holder maybe gently bent up or down
to be in line with the other blades.
After following all the steps and if the wobbling problem is not solved, a dynamic
balancing needs to be done by balancing kit. Follow the procedure listed below:
Turn on the fan and adjust the speed control (usually high speed) setting to the
speed which creates the greatest wobble.
Turn off the fan, select one blade and place the balance clip on it, half way between
the blade holder and the blade tip on the rear edge of a blade. Note the distance of
the edge of blades to the
Turn on the fan. Watch to see if the wobble is improved or worsened. Turn off the fan
again and move the clip to another blade and test again. Repeat this process with
all blades and then note the blade which is the most improved.
Move the clip back to the blade which showed the most improvement. Move the clip
inward and outward on this blade and operate the fan to find the position where the cilp
gives the the most improvement.
Next remove the clip and install a balancing weight to the top of the blade along the
center line near the point where the clip was positioned. Use a sharp knife or razor to
separate the weights.
Caution: Stay clear of the blades. If the clip for any reason is not secure, injury could
result.

11

12

13
If you need any Technical assistance or to report a fault, please contact our customer
service centre at:
Customer Service Centre