NSB FAN Ovio+ 60 User manual

INSTALLATION INSTRUCTION
CEILING FAN
TYPE :Ovio+ 60”
VOLTAGE :220~240V, FREQUENCY : 50Hz
SAVE THIS MANUAL FOR FUTURE REFERENCE
You have chosen the best.
Your ceiling fan will provide year after year satisfaction and comfort.

I. SAFETY TIPS
1. Read all instructions and safety information carefully and save this manual for future reference.
2. To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel
(switch) before you begin the fan installation or before servicing the fan or installing fan
accessories.
3. For safety and best installation result, please consult a qualified electrician.
4. Make sure you have a location selected for your fan that allows :
-Ceiling structures for the fan must be capable of supporting at least 16 kilogram of weight.
-The minimum height between the floor and the blade tips must be at least 2.3 metres.
5. After the installation is complete, check all connections are absolutely secure.
6. Do not operate the “reverse” switch until the fan has come to a complete stop.
7. Do not insert anything into the fan blades while they are rotating.

II. PART AND ACCESSORIES
1. Mounting bracket x 1
2. Canopy x 1
3. Screw for Hanger bracket x2
4. Downrod x 1
5. Cover x 1
6. Motor x 1
7. Blade x 3
8. Bottom cover x 1
9. Wire nut x 3
10. Wall plugs for screw x 3
11. Balancing kits x 1 set
12. Motor screws for blades x 7
13. Blade kits x 3
14. Remote control or transmitter (vary from model to model) x 1set
Fig. 1

III. FAN INSTALLATION INSTRUCTION
1. The hanging bracket must be securely fastened to a structural ceiling member.
2. Slide the canopy on the downrod. Thread the power leads from the fan through the canopy,
and downrod (take extra care not to pull power wires damage).
3. Set downrod into yoke. Rotate until the holes match.
4. Insert connector bolt through the holes. Be careful not to damage wiring.
5. Tighten the two down rod set screws to make sure the fan run stable.
Warning :Make sure the locking pin clip is properly engaged to prevent it from falling out. Failure to
properly install locking pin clip as noted could result in fan loosening and possibly falling.
Locking pin
Locking pin
Fig. 3
Cross bolt
Fig. 2

Ⅳ. HANGING THE FAN MOTOR ASSEMBLY
6. The ceiling fan must be installed in a location so that the blades are 300mm spacing from the tip of the blade to
the nearest objects or walls.
7. Secure the hanging bracket to the concrete ceiling or structure that is capable of carrying a load of at least 40kg,
with two long screws provided
8. Lift the fan assembly onto the mounting bracket. Fig. 5
9. Ensure the notch of the ball joint is positioned on the stopper of the mounting bracket to
prevent the fan from rotating when in operation. Fig. 6
Fig.5
Fig.5
Stopper of bracket
Fig.6
Fig.4

V. FAN ELECTRICAL CONNECTION
Warning : To avoid possible electric shock, turn off the electricity at the main fuse box or circuit
panel before the fan electrical connection. For safety and best installation result, please consult a
qualified electrician.
1. Power supply wires are connected to the control receiver. These wires are to be connected to
the supply wires from the ceiling.
2. Red (L) = Live / Hot wire from the fan
3. Black (N) = Neutral / Common wire for the fan and light
4. Green Yellow (Grounding) = Ground
ELECTRICAL CONNECTIONS ( FOR OPTIONAL WALL CONTROL)
‧Follow this wiring diagram.
ELECTRICAL CONNECTIONS ( FOR OPTIONAL REMOTE CONTROL)
‧Follow this wiring diagram.
Fig.7
Fig.8

Ⅵ. INSTALL CANOPY COVER
When the connection is completed, slide the canopy up to the mounting bracket and screws
securely.
10.Loosen the 2 screws from the bottom of the mounting bracket. Fig. 7
11.Slide the canopy up to the mounting bracket and place the key hole on the canopy over the
screw on the mounting bracket, turn the canopy until it locks in place at the narrow section of
the key holes and secure it by tightening the two set screws. Avoid damaging the electrical
wiring prepared previously.
Ⅶ. BLADE INSTALLATION
12.Insert the blade screws through the blade kit and blade then secure the blade to the motor by
tightening the 2screws. Fig.8
13.Repeat this process to install the other blades to the motor.
14.Finally install the bottom cover tothe light kit housing by rotating it clockwise. Fig. 9
Fig.9
Fig.10
Fig.11

Ⅸ. FAN MAINTENANCE
1. The fan’s natural movements may cause some connections to work loose. A clicking or rattling
noise is a certain sign of loosening screws. Check the support connections, brackets, and the
blade attachment twice a year, and tighten all screws as necessary.
2. Clean your fan periodically. Use only a cloth dampened with a mild detergent solution. Never
use solvents. Dust with a soft cloth or brush.
3. You will never need to oil your fan. It is permanently sealed bearings will provide silent, trouble
free operation for many years.