NSB FAN X LED User manual

Instruction Manual

1
Safety Precaution ……………………………………………………………………………….……………….….. 1
Parts & Accessories ……………………………………………………….……………….………………..………... 2
Fan Installation Instruction ……………………………………….……………….………………..………………. 3
Fan Mounting …………………………………………………….………………..………………...……….………… 4
Blades Assembly……………………………………………………………………..………………………………… 5
Install Light Kit ………………………………………………………………………………………………………….. 5
Electrical Connection ………………………………………………………………………………………………….. 6
Maintenance ………………………………………………………. ………………………………………………….. 7
Troubleshooting ……………………………………………………………………………………………………. …. 7
IMPORTAN: PLEASE READ BEFORE INSTALLATION
1. Installation must be carried out by a qualified wiring installer
2. Turn off the electrical mains at the circuit breaker fuse box
3. Use power supply 220-240V/50Hz.
4. When mounting the fan, ensure that the safety cable is loop across the ceiling mounting hook.
5. The ceiling mounting hook must be able to with hold a min of 35 pounds.
6. Install ceiling fan blade more than 2.3 M above floor.
7. Do not place any objects in the path of the blades.
8. When all electrical connection is done, store all wire neatly.
9. Make sure that all screws and connection are tightly screwed and secured.
10. This appliance is not intended for use by persons (including children) with Reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
11. This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
12. An all‐pole disconnection must be incorporated in the fixed wiring in accordance with the wiring rules, a
all‐pole disconnection incorporated in the fixed wiring is to be provided.
Safety Precaution
Tables of Contents

2
Parts & Accessories
01 Canopy x1
02 Cover yoke x1
03 Down rod x1
04 Motor x1
05 LED Light Kit x1
06 Blade x5
07 Blade holder screws x10
08 Wire nut x3
09 Lead wire x2
10 Balancing kits x1

3
IMPORTANT: SWITCH OFF THE ELECTRICAL MAINS THE CIRCUIT BREAKER FUSE BOX.
Follow the steps below to hang your fan properly.
1. Insert the downrod through the canopy and yoke cover
2. Through the lead wire and safety cable out the top of downrod.
3. Align the holes at the bottom of the downrod with the holes in the yoke on top of the fan motor
assembly.
4. Carefully insert the bolt through the holes in the yoke and downrod. Be careful not to jam
against the wires inside the downrod. Insert stop pin to ensure security.
5. Tighten the two screws on top of the fan motor firmly.
6. Slide down the yoke cover
Warning : Make sure the stop pin is properly engaged to prevent it from falling out.
Failure to properly install stop pin as noted could result in fan loosening and
possibly falling.
Fan Installation Instruction
Canopy
Cover yoke

4
1. “J” Hook mounted ，When mounting the fan, ensure that the safety cable is loop across the
“J”hook.
2. “U” Hook mounted Remove the bolt, stop pin, nut, washer and rubber pulley from the downrod.
Place the rubber pulley onto “U” hook and fix back the bolt, stop pin, nut and washer.
3. Remove the safety Cable Screw from the down rod bracket. Arrange and tie the Safety Cable as
step 2.Firmly screw the Safety Cable onto the down rod.
Fan Mounting
Stop pin

5
1. Insert the blade screws through the blade then secure the blade to the motor by tightening the 2 screws
2. Repeat this process to install the other blades to the motor
1. Connect the plugs together wires from housing assembly to the wires from light kit.
2. Finally install the light kit to the housing by rotating it clockwise until tighten to secure the
position.
Blades Assembly
Install Light Kit

6
1. Before installing the fan turn off the power supply.
2. With the two pieces of lead wires from the screw pack, connect the wire to the fan.
3. All electrical connections must be in accordance with local and national electrical code
standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a
qualified electrician.
Connect the red & black wire to the house’s supply wire. Diagram shows a complete
assembly of the ceiling fan with safety wire mounted on the hook. Supply leads
accommodated in the canopy.( Refer wiring diagram below)
RED----------LIVE WIRE
BLACK------NEUTRAL WIRE
YELLOW GREEN -----GROUND WIRE
Finally raise the top canopy and tighten it with the screw attached
Electrical Connection

7
Due to fan’s natural movement, connections may get loose after a period of usage.
To ensure a proper and safety usage, We are highly recommended to inspect and tighten all
connections every 6 months.
CLEANING
Clean your fan periodically to prolong its new appearance. Basic cleaning procedures are as
follows:
1. Use only lukewarm water. Do not use detergent, corrosive or acidic solution.
2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will
scratches the surface.
3. Apply a thin coat of furniture polish to the wooden blades will protect and enhance the
appearance.
4. To cover small scratches, apply a light coat of shoe polish over it.
5. There is no need to lubricant the fan.
Check on the following before lodging a service report.
SYMPTOM
PROBLEM
SOLUTION
Fan not moving
1. Main cables not connected
2. Wire connection loose
1. Check main and branch circuit
Breakers or fuse.
2. Check the line wires
connections to the fan and
switch housing.
Fan noisy
1. Housing screws are loose
2. 2.Wire and nut connections
rattles against each other.
3. Canopy touches the ceiling
1. Tighten all screws
2. Separate and store neatly the
wire connections from the
nut.
3. Check to ensure the canopy is
not touching or too close to
the Ceiling.
Remote control Not working
1. Remote and receiver code
different
2. Battery not installed
3. Weak battery
4. Check that the codes to
ensure exactly the same
5. Install the remote control
battery
6. Change a new battery
Maintenance
Troubleshooting