NSB FAN KELLY Installation and operating instructions

To avoid the possibility of causing injury to users or damage to property, please follow all the explanations as below.
Untuk mengelakkan kemalangon atau kerosakkan harta benda, sila patuhi semualangkoh pencegahan dibawah.
(a) Ceiling Fan must be mounted above 2.5m from
the floor and 1 m from the wall to the Blade.
Kipas mestilah dipasang pada jarak kipas dengan
fontoi melebihi 2.m danjarak bilah kipas dari
dinding melebihi 1m.
(b) Avoid fixing inside a dome ceiling.
Elakkan pemasangan kipas di siling berbentuk kubah.
11
Down Covering
Down Cover

2
Caution
Care and maintenance
Specificationsare subject to change without prior notice.
(a) This appliance must be earthed.
(b) Do not attempt to repair the fan. Always contact our authori`ed service agent for repair.
(c) Be sure to use it in a dry GXKG.
(a) Keep the fan cle
(d) Ceiling fan installation and electrical wiring must be done by qualified technician in accordance
an.
(b) Do not install the ceiling fan at high humidity or flammable areas.
(c) Do not bend the blades during installation, blades balancing or fan cleaning.
(d) Do not clean the fan using harsh solvent containing erodible material such as gasoline or petroleum.
Model
KELLY
Fan Size
220-240V
Voltage
50Hz
25
Motor power
W max
RPM
Max.Speed(RPM)
2.89
Nett Weight
KG
9
Gross Weight with Box
KG
Color
with all applicable codes and air conditioning engineers (ASHRAE) or the local qualied authorities.

3
WARNING:TURN OFF THE MAIN SWITCH AT THE DB (ELECTRICAL DISTRIBUTION BOX)
STEP1: Assemble suspension system
the figure A.
STEP : Power connection
RECEIVER

4
a) nsert
STEP : Fan blade installation
STEP :
a) According to Figure align the lamp plate with the screw hole and lock it with the screw. Put in the LED lamp, connect
the power cord, and fasten the lamp cover.
special

Pairing the remote control:
Step 1)Turn on the ceiling fan.
Step 2)Within the first 20 seconds,
continue pressing the button with
and start step 1)and step 2) again.

without feeling
the wind)
children.
The 1-6 YVKKJ change randomly to feel the MKTZRKIUURHXKK`KKRRKIZ.
eect

Symptom Possible Solution
Wobbles -Make sure that all the screws securing the blades are securely fastened.
-Make sure that all the blades are securely fastened.
-If you have installed more than one fan Make sure their distance is not
less than 2 meters.
-If the blades are damaged,call up the service center fora replacement but
there will be charges incurred if found not due to manufacturing fault.
Noisy -Check all the mounting, if loose, tighten.
jerks upon startup
Pergerakan permulaan
terenjat
No Airflow
Tiada aliran angin
-This is normal as it is powered by a 3 phase brushless DC motor.
It won't affect the performance.
-Make sure that it is not in "reverse function" mode.
Fan not functioning -Make sure that all the wires are securely connected.
-When the voltage drops below 140V or exceeds above 270V for more than 5
During High Speed,
the fan turning fast
seconds,the motor will cut off automatically.When the voltage is back to
normal,it will turn on automatically.
and then slow
-This is normal as the motor is not only protected by a Voltage regulator,
it is also protected by an additional thermal sensor where it will limit
the motor temperature from rising to no more than 75 . It is to increase
the life span of the motor.

clevis
To ensure safety, kindly check the following:
(a) The ceiling fan is securely fixed to the main hook.
(b) The safety wire is securely fixed and tightened by a screw.
(c) The wiring between the power supply and ceiling fan is connected properly and correctly.
(d) Make sure all the screws to secure the plastic covers are tightened properly.
(e) The screws for securing the fan blade are tightened properly.
Care of Your Fan
Here are some suggestions to help you maintain your fan
actual period of
usage support connections, brackets, and blade attachments twice a year. Make sure
they are secure.
2.Clean your fan periodically to help maintain its new appearance over the years. Use only a soft
enhanced beauty. Cover small scratches with a light application of shoe polish.
brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to
minimize discolouration or tarnishing. Do not use water when cleaning. This could damage
the motor, the wood, or possibly cause an electric shock.
3.You can apply a light coat of furniture polish to the wood blades for additional protection and
4.There is no need to oil your fan. The motor has permanently lubricated sealed ball bearings.
after