NTI UNIMUX Series User manual

MAN435 REV 1/30/24
UNIMUX-HD4K18GB-x
4K 18Gbps Video USB KVM Switch
Installation and Operation Manual
UNIMUX-HD4K18GB-8 (Front and Rear View)
UNIMUX-HD4K18GB-32 (Front and Rear View)
UNIMUX Series

i
UNIMUX-HD4K18GB-16 (with included cable management tray)
UNIMUX-HD4K18GB-32 (with included cable management trays)
TRADEMARK
UNIMUX and the NTI logo are registered trademarks of Network Technologies Inc in the U.S. and other countries. All other brand
names and trademarks or registered trademarks are the property of their respective owners.
39B38BCOPYRIGHT
Copyright © 2024 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
40B39BCHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the
right to make changes in the product design without reservation and without notification to its users.
FIRMWARE VERSION
Current Firmware Version 1.01
Typographic Conventions
The table below offers examples of text format and its meaning when that format is used in place of the standard font (Helvetica)
used throughout this manual.
Typeface meaning Font Configuration Example
On-screen computer output Courier New-(not bold) C:>
What you type on the computer Courier New-bold C:>edit text.bat

ii
UUTABLE OF CONTENTS
0B0BINTRODUCTION.............................................................................................................................................................1
1B1BMATERIALS....................................................................................................................................................................2
2B2BFEATURES AND FUNCTIONS.......................................................................................................................................3
3B3BInstall Cable Management Tray ......................................................................................................................................4
4B4BRACKMOUNTING INSTRUCTIONS...............................................................................................................................5
14B14BTo Mount to a Rack .....................................................................................................................................................5
5B5BINSTALLATION...............................................................................................................................................................6
15B15BRS232 Connection.......................................................................................................................................................8
16B16BPower-Up Sequence....................................................................................................................................................9
17B17BLimitations....................................................................................................................................................................9
6B6BUSING THE UNIMUX SWITCH ....................................................................................................................................10
18B18BFront Panel Control....................................................................................................................................................10
19B19BKeyboard Control.......................................................................................................................................................10
7BUser Access Functions..................................................................................................................................................11
20B20BOCommand Mode........................................................................................................................................................11
26B26BUUNavigation...............................................................................................................................................................11
27B27BUUSettings Menu.........................................................................................................................................................12
28B28BUUBroadcast Mode......................................................................................................................................................13
29B29BUUScan Mode..............................................................................................................................................................14
30B30BUUNormal Mode ..........................................................................................................................................................15
31B31BUUAdministrator Settings.............................................................................................................................................16
32B32BUUPort Name List........................................................................................................................................................17
33BUHot Keys .................................................................................................................................................................18
8B8BRS232 CONTROL.........................................................................................................................................................19
21B21BRS232 Connections and Configuration.....................................................................................................................19
34B33BUURemote Connection................................................................................................................................................19
35B34BUUBaud Rate...............................................................................................................................................................19
36B35BUUCommand Protocol.................................................................................................................................................19
22B22BNTI Switch Control Program For Windows 7, 8,10 and 11........................................................................................20
23B23BSerTest- RS232 Interface Test Program...................................................................................................................21
37B36BUUMain Options...........................................................................................................................................................21
24B24BFirmware Update.......................................................................................................................................................23
9B9BKEYBOARD FEATURES..............................................................................................................................................25
25B25BKeyboard-To-Computer Translation..........................................................................................................................25
38B37BUUTranslation Capabilities ..........................................................................................................................................25
10B10BTROUBLESHOOTING..................................................................................................................................................26
11B11BTECHNICAL SPECIFICATIONS...................................................................................................................................27
12B12BINDEX............................................................................................................................................................................28
13B13BWARRANTY INFORMATION........................................................................................................................................28
UUTABLE OF FIGURES
Figure 1- Install cable management tray(s).....................................................................................................................4
Figure 2- Secure rackmount ears to switch.....................................................................................................................5
Figure 3- Secure switch to a rack....................................................................................................................................5
Figure 4- Connect a HDTV monitor.................................................................................................................................6
Figure 5- Connect the device(s)......................................................................................................................................6
Figure 6- Connect the AC line cord.................................................................................................................................7
Figure 7- Connect each CPU..........................................................................................................................................7
Figure 8- Connect Terminal for RS232 Control...............................................................................................................8
Figure 9- Compatible device combinations.....................................................................................................................9
Figure 10- Port List (Main Menu) ..................................................................................................................................11

iii
Figure 11- Help Menu....................................................................................................................................................12
Figure 12- Settings Menu..............................................................................................................................................12
Figure 13- Stop USB Device Reminder warning...........................................................................................................13
Figure 14- Settings Menu..............................................................................................................................................13
Figure 15- Broadcast List..............................................................................................................................................14
Figure 16- Settings Menu..............................................................................................................................................14
Figure 17- Scan List......................................................................................................................................................15
Figure 18- Administrator Settings..................................................................................................................................16
Figure 19- Port Name List.............................................................................................................................................17
Figure 20- Settings Menu..............................................................................................................................................18
Figure 21- Front Panel Mode LEDs ..............................................................................................................................18
Figure 22- RS232 Communication Illustrated...............................................................................................................19
Figure 23- Keyboard Layouts........................................................................................................................................25

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
1
0B0BINTRODUCTION
The UNIMUX™ 4K 18Gbps HDMI USB KVM Switch allows a user to control up to 32HDMI 2.0 Ultra-HD 4Kx2K 60Hz 4:4:4 USB
computers with one USB keyboard, USB mouse, and 4K HDMI monitor. Dedicated internal microprocessors emulate keyboard
and mouse presence to each attached CPU 100% of the time so all computers boot error-free.
Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 @24/30/60Hz RGB/YUV 4:4:4, HDTV resolutions to
1080p @120Hz, and up to 1920x1200 (WUXGA).
HDMI features supported:
oHDMI 2.0
oUp to 12-bit Deep Color on input and 8-bit on output.
oDolby TrueHD, DTS-HD Master Audio, Dolby Digital, Dolby Digital+, Dolby Atmos, LPCM 2/5.1/7.1CH, DTS 5.1,
and DTS:X
oRGB, YUV 4:4:4, YUV 4:2:2, and YUV 4:2:0
oBandwidth up to 600 MHz (18Gbps)
o3D (1080p @60Hz)
oHDR
HDCP 2.2 compliant.
Features NTI's patented true autoboot USB switching –all attached computers can be booted simultaneously.
Compatible with USB computers (PC and MAC) with HDMI outputs.
Control the switch through the front panel buttons, keyboard commands, OSD, or RS232.
Two transparent USB 2.0 ports, in addition to keyboard and mouse ports, for connecting USB devices such as printers,
game controllers, USB flash drives, touch screen monitors, whiteboards, etc.
oSupports high-speed (480 Mbps), full speed (12 Mbps), or low speed (1.5 Mbps) USB devices.
Supports Plug-n-Play specification.
High quality steel construction.
Flash upgradeable.
Rackmount kit included.
Cable management tray included.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
2
1B1BMATERIALS
41B40BMaterials supplied with this kit:
NTI UNIMUX-HD4K18GB-x (4,8,16,24 or 32 ports) 4K 18Gbps Video USB KVM Switch
Line cord, country specific
Rack mount kit
1- DB9 Female-to-RJ45 Female adapter
1- 5 foot RJ45-to-RJ45 CAT5 patch cable
4- Rubber feet
Cable Ties (Qty= # of Ports + 2)
Cable Management Tray with four #6-32 x 1/4" flat head screws (x2 for 24 and 32 port units)
42B41BMaterials Not supplied but REQUIRED:
HD-xx-MM cable for each 4K monitor being connected to the switch and for each PC being connected- available in 3,6,10,
15,25,30,and 50 foot lengths
NOTE: Only supports up to 10 feet lengths for 4Kx 2K@60Hz resolutions and up to 50 foot cables for 1080p
DVI-HD-1/2/3/5M-MM cable for applications where the video source is DVI- available in 1,2,3 and 5 meter lengths.
oSupports resolutions to 1080p.
DP-HD-xx-MM cable for applications where the video source is DisplayPort- available in 3,6 and10 foot lengths
NOTE: Only supports up to 10 foot lengths for 4Kx 2K@60Hz resolutions
Supports up to 1080p@60Hz for MAC computers.
HD-ACT-xx-MM 4K HDMI Active Cables for connection of an HDMI computer or display up to 100 feet away. Available in
20,25,30,40,50,60,75 and 100 foot lengths.
oSupports 4K@60Hz up to 60 feet on input and output connections
oSupports 4K@30Hz up to 100 feet on output connections and up to 75 feet on input connections.
where:
xx is the length of the cable in feet
MM indicates male-to-male connector
USB2-AB-x-5T male USB Type A to male USB Type B interface cable for each USB device being connected to the switch.
Many are available from NTI in 0.5 meter and 3,6,10 and 15 foot lengths. Go to HHUUhttps://www.vpi.us/c/2-0-usb-cables-159UUHH.
Cables can be purchased from Network Technologies Inc by calling [phone] (800-RGB-TECH) in the US and Canada or
[phone] (worldwide).

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
3
2B2BFEATURES AND FUNCTIONS
Item Type Description
1 USB Type A Female Transparent USB port for connecting low-, full-, or high-speed USB 2.0 devices
2 LEDs For visual indication of connection between the user and a specific CPU.
3 Switches Push to manually switch to a specific CPU or change the switch operating mode
4 LEDs For visual indication of switch operating mode
5 IEC Connector For attachment of country-specific power cord
6 Power Switch To control the ON/OFF function of the switch
7 RJ45 Female RS232 (DCE) connection for attachment of RS232 control cable
8 USB Type A Female For connection of user USB device(s)
9 HDMI Female For connection of user monitor cable
10 USB Type B Female For connection of USB device cable from CPUs
11 HDMI Female For connection of video cable from CPUs
12 Button For performing firmware updates

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
4
3B3BINSTALL CABLE MANAGEMENT TRAY
Your UNIMUX KVM Drawer comes with a cable management tray to provide a means of securing the cables that plug into the
rear of the USB KVM Switch. For 24 or 32 port units, two trays are provided, one to mount at the bottom and one at the top of
the case.
Install the cable management tray(s) using the #6-32 x 1/4" flat head screws provided.
Use the cable ties (supplied) to secure the cables to the tray. Securing the cables will help to insure optimum performance.
Figure 1- Install cable management tray(s)

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
5
4B4BRACKMOUNTING INSTRUCTIONS
This NTI switch was designed to be mounted to a rack or to sit on a desktop. It includes rackmount ears to make attachment to a
rack easy, and rubber feet to be applied to the bottom of the case if it will instead sit on a flat surface. If this will sit on a flat
surface, simply apply the rubber feet to the bottom of the case in each of the 4 corners.
14B14BTo Mount to a Rack
1. Attach the ears to the switch using the 6-32x3/16" flat Phillips-head screws (6) provided as shown in the illustration below.
The holes in the ears should line up with pre-threaded holes in the sides of the NTI switch. Tighten the screws securely.
Figure 2- Secure rackmount ears to switch
2. Install 4 captive nuts (not provided) to the rack in locations that line up with the holes in the mounting ear on the NTI switch.
3. Secure the NTI switch to the rack using four 3/16" diameter screws (not provided). Each screw should be of sufficient length
to go completely through the NTI mounting ear, rack frame and fully engage all threads in the captive nut. Be sure to
tighten all mounting screws securely.
4. Attach all cables securely to the switch and where necessary supply adequate means of strain relief for cables.
Figure 3- Secure switch to a rack
6-32x3/16"
Flat Head
Screws
(Provided)
Rackmount Ear
NTI Switch
Front of Switch
Captive Nuts
3/16" Diameter Screws
Rack
(not provided)
(not provided)
NTI Switch

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
6
5B5BINSTALLATION
1. It is not necessary to turn the CPUs or monitors OFF during this installation.
2. Connect the cable from a monitor to the HDMI connector labeled “HDMI OUT” on the UNIMUX (See Fig. 4 below.)
Figure 4- Connect a HDTV monitor
3. Connect the male USB type A connector on the keyboard cable to either one of the two USB type A female connectors
labeled "KYBD/MOUSE" on the rear panel of the UNIMUX.
4. Connect the male USB type A connector on the mouse cable to the remaining USB type A female connector labeled
"KYBD/MOUSE".
Figure 5- Connect the device(s)

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
7
5. Connect the AC line cord to the UNIMUX. (See Fig. 6 below.)
Figure 6- Connect the AC line cord
6. Connect each CPU to the USB switch using a HD-xx-MM video and USB Type A-B device cable – REQUIRED
(not supplied). (See XXFigure 7XX below.)
7. Group the input device and monitor interface cables from each CPU, making sure that cables from the first CPU are
connected to the UNIMUX at connectors "CPU IN1" and "HDMI IN1". Cables from the second CPU should
connect to "CPU IN2" and "HDMI IN2" connectors...etc.
Figure 7- Connect each CPU
NOTE: For 4Kx2K @ 30Hz resolution, use maximum 30 foot HD-xx-MM cables
NOTE: For 4Kx2K @ 60Hz resolution, use maximum 10 foot HD-xx-MM cables
NOTE: For 1080p resolution, use maximum 50 foot HD-xx-MM cables.
NOTE: DVI-HD-1/2/3/5M-MM cables also work supporting resolutions up to 1920x1080@60Hz.
If the computer is running a
Mac OS any attempt to
convert the signal twice with
adapters and cabling will fail.
For example: USB-C to DVI
to HDMI monitor, or DVI to
HDMI to VGA monitor.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
8
15B15BRS232 Connection
If the RS232 is going to be used, connect one end of the CAT5 patch cable (supplied) to the port labeled “RS232” on the rear of
the UNIMUX. Plug the other end of the CAT5 cable into the RJ45-to-DB9 adapter (supplied), and connect the adapter to the
RS232 port on the control terminal. Follow the instruction under “RS232 Control” on page 19 for configuration and use of the
RS232 control feature.
Figure 8- Connect Terminal for RS232 Control

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
9
16B16BPower-Up Sequence
The UNIMUX can be powered at any time.
The CPUs can be powered at any time although if a CPU needs a keyboard and/or mouse at power-ON it should be powered
after connecting to and powering-ON the UNIMUX.
USB input devices (keyboard and mouse) can be hot plugged to and from the UNIMUX at any time.
Approximately 5 seconds after powering ON the UNIMUX, the following splash screen will appear on the monitor:
Once the splash screen goes away, the UNIMUX is booted
up and the monitor connected to Port 1 will display the
desktop image for the connected CPU. The user can
continue with normal operation of the connected CPU.
17B17BLimitations
If the computer is running a macOS, converting the output connector more than once will not work. I.e., USB Type C to
HDMI and then back to DVI for the monitor.
Only USB input device or hub cables can be connected to the UNIMUX at the USB Type A female ports labeled
"KYBD/MOUSE". (See Features and Functions on page 2, item 8.)
A USB hub (single or multi-port) can be used provided only USB input devices are plugged into it.
Only a USB Windows keyboard or USB mouse may be connected to the USB port on a USB MAC keyboard
A maximum of 7 devices (including hubs) may be connected to the UNIMUX directly.
See XXFigure 9XX for some examples of input device combinations that can be used with the UNIMUX.
Figure 9- Compatible device combinations

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
10
6B6BUSING THE UNIMUX SWITCH
Once the UNIMUX is properly connected, the UNIMUX will enable a connection to be made between the CPUs attached to its
VIDEO and CPU ports and the monitor and input devices attached to the MONITOR and DEVICES ports. The LEDs on the
control panel of the UNIMUX will illuminate depending on which port (and corresponding CPU) is being connected to the monitor
and input devices.
The UNIMUX can be controlled by four methods:
front control panel using touch-switches and LEDs
keyboard control through Command Mode
mouse clicks from within some menus of Command Mode
RS232 commands
18B18BFront Panel Control
There is a touch-switch and LED on the front panel of the UNIMUX for each CPU the switch will connect the monitor and
input devices to. Pressing any touch-switch on the front panel of the UNIMUX will connect the corresponding CPU to the monitor
and input devices.
Holding down any front panel touch-switch for more than 2 seconds will cause the UNIMUX to cycle through all modes of
operation including COMMAND, BROADCAST, SCAN, and NORMAL (described in "User Access Functions" beginning on page
11). The three MODE LEDs on the front panel indicate which mode is selected. Release the touch-switch when the LEDs
indicate the desired mode. When no mode LEDs are illuminated the user is in Normal Mode controlling directly the CPU to which
the user is connected through the UNIMUX.
19B19BKeyboard Control
Keyboard control of the UNIMUX can be achieved using Command Mode (only from the keyboard attached to the
"KYBD/MOUSE" ports)- operated using the keyboard and mouse in conjunction with OSD menus superimposed onto the monitor.
By pressing <Ctrl> + < ` > (accent key), the user can enter Command Mode. Once in Command Mode, typing a series of
commands will cause the UNIMUX to connect the user to any one CPU connected to the switch. Pressing the <Esc> key will exit
Command Mode.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
11
7BUSER ACCESS FUNCTIONS
20B20BOCommand Mode
When entering the Command Mode from the keyboard using the <Ctrl> + <`> (accent key), the OSD menu will automatically
appear on the monitor in addition to illuminating the COMMAND indicator LED on the USB KVM switch. This provides a visual
way to control the UNIMUX.
26B26BUUNavigation
Keyboard Key Action
Up/Down Arrow Select previous or Next port (while in the Port List)
Page Up/Down Advance to previous or to the next page of the Port List
Home Select the first port in the displayed port list
End Select the last port in the displayed port list
<number> Select and switch to Port Number
Enter Execute that selection
Shift-Tab Move to previous field in the menu
Tab Move to next field in the menu
Space Toggle the selection of the highlighted field
F1 Bring up the Help Menu (see XXFigure 11XX)
Esc Back up in the menu to the previous page or Exit the OSD menu
The mouse can also be used to control the UNIMUX within the Command Mode menu.
The mouse cursor can be moved to anywhere on the OSD menu. Text in blue is selectable. The user
can then single-click the left mouse button to make a selection, double-click to perform that function.
Ports listed on the screen can be selected by moving the cursor onto that port and clicking. If the USB Device
Reminder is enabled, an additional press of the <Enter> key will be needed (unless you press <Esc> and cancel the
change).
Note: When switching ports, there will be a 4.5 second delay (@30Hz) or 7.5 second delay (@60Hz) to see the result
on the monitor.
To scroll through the displayed ports on the screen simply click on the up and down arrows located to the right of the
port names displayed.
Figure 10- Port List (Main Menu)
To change the way the port list is displayed, the user can click on the "#" sign to have the list displayed numerically, or click in
"Name" to have the list displayed alphabetically. If the user decides to rename the ports to something easy to remember, listing
them alphabetically may be the most desired setting.
Note: The user must
exit Command Mode
to type to a CPU.
To exit Command
Mode, either hold
down any touch-
switch on the front
panel for more than
2 seconds, mouse
click on "Exit" OR
press <ESC> on the
keyboard.
Click to sort b
y
p
ort number Click to sort al
p
habeticall
y
Click to scroll

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
12
Figure 11- Help Menu
27B27BUUSettings Menu
From the Settings Menu the user can quickly change the status of the major functions in the UNIMUX.
Figure 12- Settings Menu
The user can change the status of Scan Mode and Broadcast Mode between Disabled (red text) and Enabled (green text). Click
on the status indicated to toggle it.
The user can enable or disable the "Stop USB Device" Reminder notice. While enabled, any time the user attempts to change to
a different port number, a warning message will pop up forcing a decision to either proceed with or cancel the attempt. This
provides opportunity for the user to properly eject a USB flash drive (or any other device) that may be harmed by an abrupt loss of
connection between the user and the PC the flash drive is connected to.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
13
To respond to the Stop USB Device warning, either click "Enter" or "Esc" with the mouse, or use keyboard keys.
Figure 13- Stop USB Device Reminder warning
From the Setting Menu the user can also toggle the OSD menu to either be Opaque (have solid color) when on the display, or to
be transparent (see-through). Click on the setting to toggle it.
The user can also adjust OSD audio feedback volume from low, to medium, to high or just disable it.
28B28BUUBroadcast Mode
Broadcast Mode enables the user to select specific ports (see XXFigure 15XX) to be active in Broadcast Mode. Only the selected ports
will receive keyboard messages in Broadcast Mode.
To activate or deactivate Broadcast Mode from the Command Mode menu, from the main menu click on Settings. From the
Settings menu, click to display either Disabled (deactivated) or Enabled (activated).
Broadcast Mode enables the user to type characters to more computers simultaneously. From the Administrator Settings-
Broadcast List menu (see page 19) the user can edit the list of ports that receive data in Broadcast Mode. A port doesn’t receive
broadcast data if the port is not in the Broadcast Mode list.
Note: The user must type somewhat slowly when in Broadcast Mode (less than 20 wpm).
Note: While in Broadcast Mode the mouse will not work.
Figure 14- Settings Menu

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
14
Figure 15- Broadcast List
From the Broadcast List, click on a port number to toggle its status. Ports displayed in green are included in the broadcast, ports
in red are not. To quickly select all ports, click on "Enable All". To quickly deselect all ports, click on "Disable All".
Selections are automatically saved.
29B29BUUScan Mode
Scan Mode enables the user to select specific ports (see XXFigure 17XX) to be active in Scan Mode. Only the selected ports will be
scanned in Scan Mode.
To activate or deactivate Scan Mode from the main menu click on Settings. From the Settings menu, click to display either
Disabled (deactivated) or Enabled (activated).
Figure 16- Settings Menu
When in Scan Mode the switch scans to each port selected in the Scan List. (The SCAN LED on the front panel will illuminate and
remain ON while in Scan Mode.) Scan mode will connect to the selected ports, whether those ports are powered ON or not. The
ports with the CPU powered-ON remain active while in use until becoming idle for the configured dwell time (XXFigure 17XX) (default
time-out period is 15 seconds) before switching to the next selected CPU port. See Command Mode section above for configuring
the scan dwell time.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
15
Note: The keyboard and mouse must remain idle for the full scan dwell time before the switch selects the next active
port.
Figure 17- Scan List
From the Scan List, click on a port number to toggle its status. Ports displayed in green are included in the list to be scanned,
ports in red are not. Toquickly select all ports, click on "Enable All". To quickly deselect all ports, click on "Disable All".
Selections are automatically saved.
Click on the number next to "Dwell Time" to select the field and enter a number between 0 and 255 (default is 15) to configure the
length of time the connection will remain with a CPU before switching to the next CPU while the UNIMUX is in Scan Mode.
30B30BUUNormal Mode
When the UNIMUX is not in Command, Broadcast, or Scan mode and all of the UNIMUX mode LEDs are OFF, the user is in
Normal Mode, controlling the CPU to which the user is connected through the USB KVM switch.

NTI UNIMUX SERIES HD4K 18GB VIDEO USB KVM SWITCH
16
31B31BUUAdministrator Settings
The Administrator Settings menu provides access to specific administrative functions of the UNIMUX. From the Main Menu
select Settings, then Administrator Settings.
Figure 18- Administrator Settings
Click the Port Name List to bring up a page where the names displayed for the UNIMUX and for each port can be edited.
Clicking on the Port Name List or Scan List will bring up the list of ports that can be set to be affected by Broadcast and Scan
modes (pages 13 and 14)