Repotec RP-IPG814-2F User manual

Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2022, All Rights Reserved.
1
User manual
Hardened Industrial 16 port Gigabit PoE Switch, 14 x 10/100/1000M TX 30W PSE + 2 x 1000M SFP,
48-56VDC input voltage, operating temp.: -40°C to +75°C
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received; including interference that may
cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55032/35 class A for ITE, the essential protection requirement of
Council Directive 2014/30/EU on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date. Please check with your local
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.

2
Introduction:
This Industrial PoE switch is designed with Hardened Ethernet and PoE controllers
to ensure performance in harsh environment. It is equipped with 14 ports 30Watts
Giga TX PSE and can deliver up to 300Watts of power to your PD devices.
All 16 ports are independent and can all be used for easy expansion of your
network application. With our unique Cold-Design technology, it will not only
power up your PD and also reduce its excessive heat to a minimum.
It has been rigorously tested for your security, surveillance, and telco applications.
This unit can also be cascaded/daisy-chained to other devices to cover wider areas
through the SFP connection.

3
Installation package:
This unit can be wall mounted or din-rail mounted. Wall mount brackets and din-rail bracket
are included.
Power connection
This unit provides a 6 pin terminal block. PoE functions can be operated from 48-56VDC
power input. Always make sure your input voltage is within this supported voltage range
for each model.
WARNING – any exceeded input voltage will not make this unit function and may
damage this unit.
This unit comes with 3 power input sources. P1, P2, and P3.
To connect power: Follow the printed polarity for P1+, P1-, P2+, P2-, and ground. Connect
positive wires to P1+ and/or P2+, connect negative wires to P1- and/or P2-, and connect the
neutral wire to the ground screw as shown.
Power DIN: This unit contains an extra P3 port for power DIN. This power DIN can power
the unit via external power adapter.
Relay: This unit includes an additional 24V@1A relay circuit for special purpose. When 2
powers are connected, the relay is in OPEN mode. If only one of the power sources is
connected, the relay changes to SHORT mode. This relay will only work with P1 and P2. It is
independent from P3.

4
Power connecting procedure:
STEP 1 – Pull out 6 pin terminal block.
STEP 2 – Connect wire to P1+, P1-, P2+, P2-, and the neutral wire to the ground screw.
STEP 3– Plug connected 6 pin terminal block back into place.
Or, Connect the P3 power DIN from external power adapter.
WARNING -- Always SHUT OFF power source to connect power wire.
WARNING -- Always ground the power source to maintain a clean power input. Cheaply
made power supplies create too much noise and will cause the power input to fluctuate
when connected to this unit. To avoid this, always ground the power source to maintain a
clean power input.

5
LED indicator
PoE (Amber)
ON – PD is
detected on
designated
port.
LNK (Green)
ON—TX port is
detected
OFF – TX port is
not detected
Flashing – TX
port is active
F15, F16 (Green)
ON – F15 or F16 SFP
fiber is detected
OFF – F15 or F16 SFP
fiber is not detected.
Flashing – F15 or F16
SFP fiber is active
P1(Green)
ON -- P1+, P1- is
connected
P2(Green)
ON -- P2+, P2- is
connected
P3 (Amber)
ON－P3 is connected
via Power DIN
RLY(Amber )
ON – Only PW1 or PW2 is connected
OFF-both PW1 and PW2 are connected

6
Specification
IEEE Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af PoE
IEEE 802.3at PoE+
Switch Architecture Back-plane (Switching Fabric): 32Gbps
Data Processing Store and Forward
Flow Control IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame 9KB
MAC address Table Size 8K
Packet Buffer Size 4.1Mbits
Network Connector
14 x RJ-45 10/100/1000BaseT(X) auto negotiation,
Auto MDI/MDI-X function, Full/Half duplex
14 x Gigabit POE+ 802.3at/af PSE port, 30W per port
2 x SFP 1000M
Network Cable UTP/STP Cat.5e or above Cable
EIA/TIA-568 (100m)
Protocol CSMA/CD
LED
PW1 (Green): ON
－
Power 1 is detected
PW2 (Green): ON－Power 2 is detected
PW3 (Amber): ON－Power 3 is detected for Power DIN
RLY (Amber): ON－Connect only PW1 or PW2
OFF－Both PW1 and PW2 are connected
TX/RJ-45 port:
LNK (Link/Active) (Green): ON－TX port is detected
Flashing－TX data is
transmitting/receiving
PoE (Amber): ON－PD is detected and PSE is activated
OFF－PD is not detected
SFP Fiber Per port:
F15/F16 (Green)
ON – F15 or F16 SFP fiber is detected
Flashing – F15 or F16 SFP fiber is active
Reserve polarity protection Present
Overload current protection Present

7
Power Supply Redundant Dual DC 48V-56V Power Input
Power Consumption 5.76W@48 VDC full load, Without PoE
Alarm Relay Contact
Relay outputs with current carrying capacity of 1 A @24VDC,
Relay in open circuit mode when 2 powers are connected. in
short circuit mode when only one power supply is connected
PoE power
PoE power per port 30watts.
Maximum total power 300Watts with 56VDC input,
Supports IEEE 802.3af/at
Removable Terminal Block
Provide 2 Redundant power , Alarm relay contact ,6 Pin
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature -40°C to +75°C
Operating Humidity 5% to 95% (Non-condensing)
Storage Temperature -40°C to 85°C
MTBF (mean time between
failure) 504739 hrs (Telcordia (Bellcore), GB) at 50°C
Housing Rugged Metal, IP30 Protection
Case Dimension 155 x 48 x 120 mm (LxWxD)
Installation DIN Rail Mount or Wall Mount
Certifications:
Safety
UL 60950-1
Safety LVD (EN 62368-1)
EMC CE, FCC, EN 55032/35
EMI CISPR 32, FCC Part 15B Class A
EMS
IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV
IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV
IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV
Vibration EN 60068-2-6
Shock
EN 60068-2-27
Free Fall EN 60068-2-32

8
Housing Dimension (mm)