NTI PRIMUX Series Quick start guide

MAN054 Rev Date 5/21/2012
PRIMUX KVM SWITCH SYSTEM
FIRMWARE UPGRADE PROCEDURE
(For PRIMUX Components upgrading to Firmware Version
2.0 and later)
PRIMUX®Series

MAN054 Rev Date 5/21/2012
TRADEMARK
PRIMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.
FIRMWARE VERSION
This upgrade procedure applies to PRIMUX User Station and Host Adapters upgrading to firmware version 2.0 and
later.
WARNING: When using this procedure to upgrade a PRIMUX User Station and Host Adapters to Version 2.0
(or later) from any earlier version, it is extremely important to upgrade all Host Adapters before upgrading
the User Station. After upgrading the Host Adapters, the User Station will not recognize them until it too has
been upgraded. Also, a User Station running version 2.0 will not recognize a Host Adapter programmed with
an earlier version.

MAN054 Rev Date 5/21/2012
TABLE OF CONTENTS
Introduction.................................................................................................................................................................... 1
Common Navigation ..................................................................................................................................................... 1
Download Appropriate Firmware Upgrade Package ................................................................................................. 2
Determine if a firmware upgrade is needed................................................................................................................ 2
Determine what new firmware is available .................................................................................................................. 2
Determine the current running firmware ...................................................................................................................... 2
Determine if upgrade is needed .................................................................................................................................. 3
Prepare for PRIMUX Firmware Upgrade ..................................................................................................................... 4
Attach the COMPUTER to the User Station ................................................................................................................ 4
Put the PRIMUX User Station into Bootloader Mode .................................................................................................. 4
Upgrading Host Adapters (HA-PS2, HA-SUN, HA-USB, HA-RS) .............................................................................. 5
Prepare to Download Host Adapter code to the User Station..................................................................................... 6
Download ROM File..................................................................................................................................................... 6
Upload the ROM File to the Host Adapter................................................................................................................... 7
Verify that the proper ROM file code image resides in storage................................................................................ 7
Upload and Update Individual Host Adapters........................................................................................................... 7
Upload and Update All Host Adapters...................................................................................................................... 8
Upgrade the User Station ............................................................................................................................................. 9
Prepare for Downloading............................................................................................................................................. 9
Download ROM File..................................................................................................................................................... 9
Flash the Device with the ROM File .......................................................................................................................... 10
Upgrade the remaining ROM Files ............................................................................................................................ 10
Verify ROM Files........................................................................................................................................................ 10
FINAL VERIFICATION ................................................................................................................................................. 11
Null Modem Cable Pinouts......................................................................................................................................... 12

NTI PRIMUX FIRMWARE UPGRADE
1
INTRODUCTION
Note: It is not necessary to upgrade firmware unless you are experiencing a problem and NTI Technical
Support has recommended upgrading.
The PRIMUX CAT5 KVM System is user upgradeable. The user may need to upgrade the firmware to enable a new
feature, or to correct some improper behavior. Steps must be followed to successfully upgrade the firmware of the
PRIMUX CAT5 KVM System.
1. Download appropriate firmware upgrade package
2. Determine if a firmware upgrade is needed:
a. Determine what new firmware is available.
b. Determine the current running firmware.
c. Determine if upgrade is needed
3. Prepare for PRIMUX firmware upgrade.
4. Upgrade the firmware in each type of Host Adapter (HA-PS2, HA-SUN, HA-USB, HA-RS)
5. Upgrade the User Station firmware
6. Final verification
WARNING: When using this procedure to upgrade a PRIMUX User Station and Host Adapters to Version 2.0
(or later) from version 1.9 (or earlier), it is extremely important to upgrade all Host Adapters before
upgrading the User Station. After upgrading the Host Adapters, the User Station will not recognize them
until it too has been upgraded to 2.0 (or later). Also, a User Station running version 2.0 will not recognize a
Host Adapter programmed with an earlier version.
If the User Station has already been upgraded to firmware version 2.0 before all Host Adapters have been
upgraded, simply use the same procedure to downgrade the User Station back to version 1. 9, upgrade all
Host Adapters, and re-upgrade the User Station to version 2.0.
Note: The HA-RS Host Adapter is only compatible with User Stations running firmware version 2.0 or later.
COMMON NAVIGATION
To display the OSD COMMAND MODE menu on the attached monitor of the User Station
If the User Station is not displaying an OSD screen, using the attached keyboard:
•Press <Ctrl>+<`>
If the User Station is displaying OSD USER/ADMIN LOGIN splash, login as administrator, using the attached
keyboard:
For User Station Firmware Version 1.9 and earlier
•NAME: <ADMINISTRATOR>or <ROOT>
•PASSWORD: <NTI>
(all uppercase letters)
For User Station Firmware Version 2.0 and later
•NAME: <root>
•PASSWORD: <nti>
(all lowercase letters)
Note: If the administrator has changed the password, only the new password will permit access to the User
Station.
If the User Station is displaying any OSD screen other than the COMMAND MODE menu, using the attached
keyboard:
•Press <F10>
To display the OSD USER/ADMIN LOGIN splash on the attached monitor of the User Station:
•Display the OSD COMMAND MODE menu.
From the User Station in OSD COMMAND MODE, using the attached keyboard
•Press <L> - LOGOUT

NTI PRIMUX FIRMWARE UPGRADE
2
DOWNLOAD APPROPRIATE FIRMWARE UPGRADE PACKAGE
Download the most current firmware upgrade package from http://www.networktechinc.com/download/d-
kvmswitch-cat5.html , or receive it directly from NTI.
DETERMINE IF A FIRMWARE UPGRADE IS NEEDED
Determine what new firmware is available
Unzip the firmware upgrade package into an empty folder on the computer that will be used to transfer the firmware
to the PRIMUX system.
Refer to the RELEASE.TXT file, which details what firmware is available for upgrade, and note the revisions on the
worksheet on page 10 (the underscore ‘_’ is equivalent to the period ‘.’ for revisions).
Latest code revision available for the PRIMUX SYSTEM as of 06/26/08.
User Station revision:1_9
Host Adapter PS2 revision:1_6
Host Adapter SUN revision:1_6
Host Adapter USB revision:1_6
Determine the current running firmware
Note what revisions are currently running for each PRIMUX device type. (A worksheet to record this is on page 12.)
From the User Station, starting from the OSD COMMAND MODE menu.
For Host Adapters running revision 1.6 or earlier:
•Highlight one Host Adapter type USB, PS2, or SUN
•Press <I>- INFO
•From the HOST ADAPTER INFO screen, make note of the "Revision" on the worksheet for Host Adapter type.
•Press <X> - EXIT, to exit this screen
•Repeat for each Host Adapter type.
For User Stations running revision 1.9 or earlier:
•Press <I> - INFO.
•Press <S> - USERSTATION
•Make note of the "Rev" on the worksheet for the User station.
•Press <X> - EXIT, to exit this screen
The versions shown here will be the
last version numbers seen before all
change to “revision : 2_0”.

NTI PRIMUX FIRMWARE UPGRADE
3
For Host Adapters running version 2.0 and later:
•Press <A> - <H>
•Highlight one Host Adapter of Type USB, PS2, or SUN and press <Enter>.
•From the Edit Host Adapter screen, make note of the "Rev" on the worksheet for Host Adapter type.
•Press <Esc> to exit this screen
•Repeat for each Host Adapter type.
For User Stations running version 2.0 and later:
•Press <A> - <F> - <U>
•Make note of the "Revision" on the worksheet for User Station.
•Press <Esc> to exit this screen
Determine if upgrade is needed
Before upgrading, you need to determine which, if any, of the current running device firmware needs to be upgraded.
•On the worksheet on page 12 compare Available revision and Current Running revision, of each device type
and check the upgrade box if Available revision is newer.

NTI PRIMUX FIRMWARE UPGRADE
4
PREPARE FOR PRIMUX FIRMWARE UPGRADE
You will need an additional computer with keyboard and monitor (not already connected to the PRIMUX system
being updated). The computer must be capable of terminal emulation to include XMODEM file transfer via a serial
port (such as Windows HyperTerminal). This is called the COMPUTER. This COMPUTER needs to have the
appropriate firmware upgrade package accessible to it.
You will need a 9-pin serial null modem cable (i.e. NTI cable part # DINT-xx-FF), maximum 15 feet long (see page 12
for cable specification).
Note: It is recommended that a UPS be used on all powered CPUs that have Host Adapters being upgraded.
It is not necessary that a UPS be used on the COMPUTER or the User Station.
Attach the COMPUTER to the User Station
•Attach a 9-pin serial null modem cable (i.e. NTI cable part # DINT-xx-FF), maximum 15 feet long (see page 12
for cable specification) to the RS232 port of the User Station from the COMPUTER.
•Open the terminal emulation program (HyperTerminal) on the COMPUTER.
•Connect to the User Station through the proper COM port using the following settings: 9600,8,n,1, no flow
control.
Put the PRIMUX User Station into Bootloader Mode
For User Stations running firmware version 1.9 or earlier:
From the User Station displaying the OSD USER/ADMIN LOGIN splash, login as the administrator. Using the
attached keyboard, hold down the <Shift> key and enter
•NAME: <ADMINISTRATOR>or <ROOT>
•PASSWORD: <NTI>
Note: If the administrator has changed the password, only the new password will permit access to the User
Station.
Starting from the OSD command menu,
•Press <A> for ADMINISTRATION,
•Press <B> for BOOTLOADER/UPDATE MENU.
•Press <B> 'GO TO BOOTLOADER’.
•You will be prompted "Are you sure? (Y/N)" Press <Y> to proceed.
VGA
Multi-Scan
Monitor
"COMPUTER"
Null modem cable
Cat5 Monitor
SUN
Devices
PS/2
Devices
Mouse Kybd
RS232
USB
Devices
5VDC
2A
NETWORK
TE CHNO LOG IES
INCORPORATED
Tel:[phone]
Fax:[phone]
1275Danner Dr
Aurora, O H 4 4202
www.nti1.com
NTIR
+
(Rear View)
Cable to CPU 1
(Rear View)
Cable to CPU 2
(Rear View)
Cable to CPU 3
(Rear View)
Cable to CPU 64
CAT5 Cable
Terminating
Plug CAT5 Cable
CAT5 Cable
CAT5 Cable

NTI PRIMUX FIRMWARE UPGRADE
5
The User Station is now in bootloader mode. This is indicated by "88"' flashing on the front panel of the User Station.
The monitor connected to the "Monitor" port on the User Station will also go blank.
For User Stations running firmware version 2.0 or later:
From the User Station displaying the OSD USER/ADMIN LOGIN splash, login as the administrator. Using the
attached keyboard enter
•NAME: <root>
•PASSWORD: <nti>
Note: If the administrator has changed the password, only the new password will permit access to the User
Station.
Note: If you have just upgraded an User Station from 1.9 to 2.0, and you have not changed the password
from the default password “NTI” (uppercase letters), then the login name to login as the administrator will
be “root” (all lowercase), and the password will be “NTI” (all uppercase). The password does not change
when firmware is upgraded.
Starting from the OSD command menu,
•Press <A> for Administration Menu,
•Press <F> for Firmware Configuration.
•Press <B> for Go To Bootloader.
•You will be prompted "Are you sure? (Y/N)" Press <Y> to proceed.
UPGRADING HOST ADAPTERS (HA-PS2, HA-SUN, HA-USB, HA-RS)
The following steps must be performed in the order indicated. Do not cycle power to any device until the process is
complete.
There is only one file that needs to be uploaded per type of Host Adapter (HA).
HA Type Filename
PS2 PRIMUX_HA_PS2_<revision>.b01
USB PRIMUX_HA_USB_<revision>.b01
SUN PRIMUX_HA_SUN_<revision>.b01
SERIAL PRIMUX_HA_RS_<revision>.b01
for example PRIMUX_HA_PS2_1_6.b01
Take note of the type of Host Adapter being upgraded, PS2, SUN, USB, or SERIAL. An upgrade file for a specific
type of Host Adapter can only be applied to a Host Adapter of the same type (PS2 file for HA-PS2, SUN file for HA-
SUN, USB file for HA-USB, and SER (RS) file for HA-RS).
Note: The HA-RS Host Adapter is only compatible with User Stations running firmware version 2.0 or later.

NTI PRIMUX FIRMWARE UPGRADE
6
Prepare to Download Host Adapter code to the User Station
From Bootloader Mode, at the COMPUTER's terminal emulation program (see page 3 "Put the PRIMUX User Station
into Bootloader Mode").
•Press <Enter> to establish communications with the User Station.
The following Option Menu should be displayed along with the ‘BootlLdr User Station:’ prompt
NETWORK TECHNOLOGIES INC ALL RIGHTS RESERVED COPYRIGHT 2003
Primux User Station Boot Loader Serial Number: 00000374
Option Menu:
1: Download Data:
2: Identify Ram Data:
3: Program Flash Device:
4: Identify Flash Device:
0: EXIT and Re-Boot:
?: Option Menu
BootLdr User Station:
Download ROM File
Select a ROM File type that will be downloaded.
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <1> 1: Download Data. You will be prompted with the following message:
Download deletes old data. Continue? <Y/N>:
•Press <Y> to continue. The User Station is now waiting for a XMODEM file transfer to begin.
From the COMPUTER terminal emulator, download the selected ROM file type using the XMODEM protocol.
•Transfer file PRIMUX_HA_<type>_<revision>.b01.
Where <type> is PS2, USB or SUN, and <revision> is the upgrade revision available of the specified type.
When complete, after about 1.5 minutes, the following is displayed at the COMPUTER terminal emulator.
Download ok
BootLdr User Station:
Display the Option menu.
•Press <?> ?: Option Menu:
•Press 2 <Identify RAM Data> to display the data that has just been loaded into the User Station. Verify
that it the desired file. If not, repeat “Download ROM File” from the beginning with the proper file.
Note: If an error message is displayed, repeat these steps. If error message is displayed the second time,
contact NTI technical support.
Downloading of the selected ROM file is complete.
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <0> 0: Exit and Reboot

NTI PRIMUX FIRMWARE UPGRADE
7
Upload the ROM File to the Host Adapter
Note: This section for upgrading Host Adapters applies only to Host Adapters that have
firmware version 1.9 and earlier. Host Adapters with firmware version 2.0 and later must be
upgraded following the procedure documented in the PRIMUX CAT5 KVM System manual
for version 2.0 (or later) under “Update Host Adapter Firmware” (page 37).
Once the selected ROM file has been downloaded to the User Station, it may be uploaded to any or all of the Host
Adapters of the selected type. Ensure that all Host Adapters of the selected type to be uploaded are powered ON
and will remain powered ON during the process.
Note: It is recommended that a UPS be used on all powered CPUs that have Host Adapters being upgraded.
Note: If a Host Adapter is powered OFF during the Upload process, the Host Adapter could become unusable
and need to be sent to NTI for servicing.
From the User Station displaying the OSD USER/ADMIN LOGIN splash, login as the administrator. Using the
attached keyboard, hold the <Shift> key and enter
•NAME: <ADMINISTRATOR> or <ROOT>
•PASSWORD: <NTI>
Note: If the administrator has changed the password, only the new password will permit access to the User
Station.
Verify that the proper ROM file code image resides in storage
Starting from the OSD command menu,
•Press <A> for ADMINISTRATION,
•Press <B> for BOOTLOADER/UPDATE MENU.
•Press <I> for "USERSTAT.CODE IMAGE".
-Verify the ProdId: is HOST_ADAPTER.
-Verify the RomFunc is the Type selected. (PS2, SUN or
USB)
-Verify the Revision matches the Revision Device type on
the worksheet.
•Press <X> - EXIT "USERSTATION CODE IMAGE INFO"
Upload and Update Individual Host Adapters
This section is used to update individual Host Adapters. This is particularly useful if you are adding a new Host
Adapter to an existing segment. To upload and update all Host Adapters of the same type in one quick procedure,
see “Upload and Update All Host Adapters” on the next page.
From the User Station, starting from the UPDATE/BOOTLOADER MENU using the attached keyboard
•Press <H> for SEL.HOST and select the Host Adapter to be updated. You will immediately be returned to the
UPDATE/BOOTLOADER MENU. The selected Host Adapter to be updated will now be indicated.
Note: Be sure to select a Host Adapter of the same type as the code image that has been uploaded
(PS2,SUN, USB or SER (RS)).

NTI PRIMUX FIRMWARE UPGRADE
8
•Press <S> for SEND CODE IMAGE TO HOST to send the code image to the Host Adapter in preparation for
update. A Yes/No confirmation will be required. Press <Y> to confirm.
During the transfer, a “Waiting....” message will be displayed and a blinking yellow asterisk will appear next to the “S”
. Wait for the ’Waiting…’ message to no longer be displayed.
•Press <C> for UPDATE HOSTADAPTER CODE to complete the update for the selected Host Adapter. A
Yes/No confirmation will be required. Press <Y> to confirm. The code update will happen quickly, so no
“Waiting....” message will appear.
Upload and Update All Host Adapters
This section is used to update all Host Adapters of the same type in one command. This is particularly useful if you
have a group of Host Adapters in a segment that all need updating. To upload and update individual Host Adapters,
see “Upload and Update Individual Host Adapters” on the previous page.
From the User Station, starting from the UPDATE/BOOTLOADER MENU using the attached keyboard
•Press <A>- SEND+UPDT.CODE,ALL HOSTS A Yes/No confirmation will be required.
•Press <Y> to confirm.
During the transfer, a “Waiting....” message will be displayed and a blinking yellow asterisk will appear next to the
“A”. Wait for the ’Waiting…’ message to no longer be displayed. This process can take about 1.5 minutes per Host
Adapter.
At this point all powered Host Adapters of the selected type have been upgraded. To upgrade other Host Adapter
types, return to "Download ROM File" and follow the instructions for a different type.
Note: Flashing many Host Adapters can take a substantial amount of time. For example, 60 Host adapters
may take approximately 1.5 hours to flash.

NTI PRIMUX FIRMWARE UPGRADE
9
UPGRADE THE USER STATION
The following steps must be performed in the order indicated. Do not cycle power to any device until the process is
complete. Be sure to “PREPARE FOR PRIMUX FIRMWARE UPGRADE” (page 3) before starting this procedure.
For the User Station there are four files that need to be downloaded and flashed in any order.
PRIMUX_u_sta_<revision>.b01
PRIMUX_u_sta_<revision>.b02
PRIMUX_u_sta_<revision>.b03
PRIMUX_u_sta_<revision>.b04
for example PRIMUX_u_sta_2_0.b01 would be the file name for revision 2.0.
Each file must be individually downloaded to the User Station and flashed before proceeding to the next file. The
process is not complete until all four files are flashed.
Prepare for Downloading
From Bootloader Mode, at the COMPUTER's terminal emulation program
•Press <Enter> to establish communications with the User Station.
The following Option menu should be displayed along with the ‘BootlLdr User Station:’ prompt
NETWORK TECHNOLOGIES INC ALL RIGHTS RESERVED COPYRIGHT 2003
Primux User Station Boot Loader Serial Number: 00000374
Option Menu:
1: Download Data:
2: Identify Ram Data:
3: Program Flash Device:
4: Identify Flash Device:
0: EXIT and Re-Boot:
?: Option Menu
BootLdr User Station:
Download ROM File
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <1> 1: Download Data. The following message and prompt will appear:
Download deletes old data. Continue? <Y/N>:
•Press <Y> to continue. The User Station is now waiting for a XMODEM file transfer to begin.
From the COMPUTER terminal emulator, download the ROM file using the XMODEM protocol.
•Transfer file PRIMUX_u_sta_<revision>.b01.
Where <revision> is the upgrade revision available.
When complete, after about 1.5 minutes, the following is displayed at the COMPUTER terminal emulator.
Download ok
BootLdr User Station:
Display the Option Menu.
•Press <?> ?: Option Menu:
Note: If an error message is displayed, repeat above steps. If error
message is displayed the second time, contact NTI technical support.

NTI PRIMUX FIRMWARE UPGRADE
10
•Press 2 <Identify RAM Data> to display the data that has just been loaded into the User Station. Verify
that it the desired file. If not, repeat “Download ROM File” from the beginning with the proper file.
Flash the Device with the ROM File
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <3> 3: Program Flash Device:
When flashing the device is complete, the following message should be displayed:
Rom ID Check: Verifying Source CRC: Flashing: Writing Signature: Passed
Note: If anything is not correct contact NTI technical support.
ROM File 1 has now been flashed.
Note: Once the first ROM file is flashed you MUST continue to download and then flash all remaining ROM
files.
Upgrade the remaining ROM Files
Repeat the process starting with "Download ROM File" (page 9) to download and flash the remaining ROM Files, 2
through 4.
ROM File 2 PRIMUX_u_sta_<revision>.b02
ROM File 3 PRIMUX_u_sta_<revision>.b03
ROM File 4 PRIMUX_u_sta_<revision>.b04
Verify ROM Files
When all 4 ROM Files are completely downloaded and flashed, verify all 4 ROM files are of the same revision and
type and the flash device is useable. All revisions must be the same revision as noted on the worksheet in the User
Station - Available revision box.
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <4> 4: Identify Flash Device, to display the revisions and types of all ROM files that have been
flashed and if the flash device is useable.
The following indicates a successful upgrade has been preformed
All ROM File Revisions are the same and ‘Flash Device Is Useable’.
COPYRIGHT 2002-2005 NETWORK TECHNOLOGIES INC ALL RIGHTS RESERVED
$ProdId: USER_STATION$
$RomFunc: main
$Date: 2005/09/01 20:40:23 $
$Revision: 2.0 $
Primux User Station, Rom File 1
$Revision: 2.0 $
Primux User Station, Rom File 2
$Revision: 2.0 $
Primux User Station, Rom File 3
$Revision: 2.0 $
Primux User Station, Rom File 4
$Revision: 2.0 $
Flash Device Is Useable

NTI PRIMUX FIRMWARE UPGRADE
11
If any ROM file revision is not correct, repeat the procedure for the incorrect ROM file.
The User Station is upgraded and must be restarted.
At the COMPUTER's terminal emulation program and the ‘BootlLdr User Station:’ prompt
•Press <0> 0: Exit and Reboot
Note: If any error is detected in the newly flashed User Station, the bootloader program will not allow the
User Station to reboot into an operational mode, and will STAY IN Bootloader Mode. All 4 User Station ROM
files must be at the same revision level prior to rebooting the User Station into an operational mode. If a
reboot to operational mode fails, contact NTI technical support.
FINAL VERIFICATION
With all firmware successfully upgraded, verify the Current Running revision are proper, follow the steps on page 2
under "Determine the current running firmware" and compare the results to the Available revision shown on the
worksheet on page 12.
Test to ensure that PRIMUX CAT5 KVM System is working properly.
Note: A User Station running firmware version 2.0 (or later) will not recognize a Host Adapter running
version 1.9 or earlier. If a Host Adapter needs to be upgraded to 2.0 (or later) from 1.9 (or earlier), the User
Station must first be running version 1.9 (or earlier) in order to perform the upgrade to the Host Adapter.
Note: The HA-RS Host Adapter is only compatible with User Stations running firmware version 2.0 or later.

NTI PRIMUX FIRMWARE UPGRADE
12
NULL MODEM CABLE PINOUTS
PRIMUX to Terminal (9 PIN) null modem cable PRIMUX to Terminal (25 PIN) null modem cable
( NTI cable part # DINT-xx-FF)
PRIMUX TERIMINAL PRIMUX TERMINAL
9 pin Signal 9 pin 9 pin Signal 25 pin
Function Pin # Direction Pin # Function Function Pin # Direction Pin # Function
RxD 2 3 TxD RxD 2 2 TxD
TxD 3 2 RxD TxD 3 3 RxD
CTS 8 N/C 7 RTS CTS 8 N/C 4 RTS
RTS 7 N/C 8 CTS RTS 7 N/C 5 CTS
DSR 6 N/C 4 DTR DSR 6 N/C 20 DTR
DTR 4 N/C 6 DSR DTR 4 N/C 6 DSR
DCD 1 N/C 1 DCD DCD 1 N/C 8 DCD
SG 5 5 SG SG 5 7 SG
N/C= not connected (no cable wire)
In this cable signals CTS and RTS are connected to each other at the connector ends, and
signals DSR, DTR, and DCD are connected to each other at the connector ends.
Note: Cable length not to exceed 15ft.
PRIMUX Firmware Upgrade Worksheet
Device type Available revision
(from RELEASE.TXT)
Current Running revision
(from OSD menus)
Upgrade needed
User Station
Host Adapter – PS2
Host Adapter – USB
Host Adapter – SUN
Host Adapter – SER (RS)
MAN054 Rev. 5/21/12
Mating Face
of 25D
Female Connector
1
14
25
13
1
Mating Face
of 9D
Male Connector
2345
6789
9D Female
xx= 6,10,15 FEET
9D Female
NTI DINT-xx-FF