Nugens VC300 User manual

Optical Zoom
Conference Cam
User Manual

1
To avoid damage from stress, violent vibration, soaking during transportation, storage and installation.
Take care of each components of camera during installation, and install camera at where is affordable
enough, to avoid drop or scratches of camera case.Handle the camera parts gently, do not squeeze the
camera units hard. Please do not touch the camera lens by hand directly to avoid the lens scratched and
image quality affected.
Do not apply excessive voltage. (Use only the specified voltage) Otherwise, you may get an electric
shock or a fire may occur.Do not aim the camera at the sun or the other high luminous objects, othewise
it may cause image blurring or lens flare, even cause permanent damage to the camera.Do not clean
camera with active chemical or corrosive detergents, and remove dust or dirt on the surface of the lens
with a blower (Commercially available)·Do not disassemble any camera components, in case of abnor-
mal operation; contact your authorized dealer or the store where you purchased the product.
1.Notice
2.Performance Characteristics
3.Supplied Accessories
1. Camera technical parameters
Electric Communication
Operation Surroundings
Physics Installation Method
Input Voltage
Power
Decoder
Horizontal Rotation
Vertical Rotation
Baud
Protocol
Address Set
Operating
Environment
Operating Temp
Rotation Speed
Preset Point
Net-Weight
DC12V
12W
internal
±170°
120°
9600/38400bps
VISCA/PELCOD/P
0~255
0°~+50°
0~95%
non-condensing
Support desktop,wall mount,ceiling mount
and tripod installation
100°/s
9 remote controls
Pelco Protocol
255
1.46kg
2. Camera Parameters
1/2.7” HD color CMOS
128°~37°
F=3.0-10.0mm
2.1 Mega Pixel
3x optical zoom
Image Sensor
Effective Pixel
HD Format
Focal Length
HD Interface
FOV
Resolution
Signal System
Control parameters
Translation/
Pitching Angle
Translation/
Pitching Speed
Preset
Control Protocol
Common Parameters
Size
Color
Spec lens
1080P(1920*1080) 720P(1280*720)
USB
1080P/720P
NTSC/PAL
IR remote control supports 9 presets PELCO,Protocol supports 255 presets
-170°~170° -30°~90°
100°/s 80°/s
VISCA,PELCO-D,PELCO-P(RS-232, RS485)
Product:260*175*180mm packaging:296*225*218mm
black
(1) HD conference camera (2) DC12V-2A power supply
(3) Ceiling mount (4) Mounting screws
(5) Manual (6) Remote control
(7) USB cable

2
4.Quick Start
1.Interface definition
2.Interface diagram
DC 12V
RS-485
AB
USBIR
High Speed USB HD Video interfare keyboard control
TV
PC
1 2 3 4 5
DC 12V
RS-485
AB
USBIR
1 2 3 4 5
DC 12V Output AC 220V Input
1.IR 2.USB 3.RS-232
4.RS-485 5.DC12V

3
(1) Surface Installation
Put the camera on the desk flat, and make sure the camera in level. If want to put the camera on oblique
surface, please make sure the angle of inclination less than 15 degree for ensure camera pan and tilt
working in normal operation.
(2) Tripod Mount Installation
Twist the tripod’s screw on the camera tripod hole, then the tripod could be installed on the bottom of
camera. The tripod screw must fit below.
(3) Ceiling Mount Installation
3.Installation instructions
>
_
15°
_
<
15°
6mm
Screw specification 1/4-20UNC
1.Mounting the ceiling bracket 2.Install the camera
Mounting the bracket vertically to the ceiling with
screws.
Rotate the camera clockwise to install it.
Screw port

4
5. Remote control button description
6.Common Operations Introductions
12
13
15
14
1 2 3
1 2 3
4 5 6
7 8 9
PRESET
0
RESET
CAMERA SELECT
STD REV
POSITION
UP DOWN
HOME
PAN-TILT
MENU
PT/RESET
ZOOM
SLOW
+
-
ZOOM
FAST
+
-
FAR
NEAR
MANUAL
FOCUS
L/R
SET
AUTO
FOCUS
1.
Camera Select
Refer to the dial-up at the back of camera and choose camera
address number that you want to control(1-3)
2.
Camera Direction Control
Turning up
Turning down
Turning to left
Turning to right
1 2 3
CAMERA SELECT
HOME
*Note: Press direction key to move the camera.Press the direction
key when you need to change the angle. If you want to move the
camera slowly, just click the direction key; If you want to move the
camera fast at a large scale,just long-press the button.
(1)Remote Control Launch Window
(2)【POWER】Standby Button, pressing it, camera goes into Standby Mode;
pressing again, camera goes Power ON.
(3)【P/T Reset 】(Not applicable for this model)
(4)【CAMERA SELECT】Choose the camera number that needed to control,
to correspond the dial-up code on the back of camera
(5)【POSITION】Preset position setup keys, include【PRESET】and【RESET】
Press PRESET then Press NUMNER: to setup preset
Press RESET then Press NUMBER: to clear preset.
(6)【UP】Camera rotating horizontally in regular installed direction
(7)【PAN-TILT】Camera rotation control key, press this button and move by
the arrow direction,Press【HOME】to back to the center of vertical and hori-
zontal position.
(8)【P/T Reset 】clear all position setting.
(9)ZOOM SLOW
【Zoom SLOW+】T:Zoom out at low speed
【ZOOM SLOW-】W:Zoom in at low speed
(10)Manual Focus Mode
【MANUAL FOCUS】Start manual focus function
【FAR】Manually far focus, clearer for the distant objects, loose finger to stop.
【NEAR】Manually near focus, clearer for the nearby object, loose fing-
er to stop.
(11)【L/R SET】(Not applicable for this model)
(12)【AUTO FOCUS】Auto Focusing Button
(13) Fast Zoom Key
【ZOOM FAST +】Zoom out at fast speed
【ZOOM FAST -】Zoom in at fast speed
(14)【MENU】(Not applicable for this model)
(15)【DOWN】Camera rotating horizontally in rever-sed installed direction.

5
3.Camera Focusing Mode Control
【AUTO】Switch the focus mode to AUTO
【MANUAL】Switch the focus mode to MANUAL
【FAR】Far focus manually
【NEAR】Near focus manually
4.Camera Zoom Control
Press any one of the 4【ZOOM】to make the zoom functioning.
5.Preset Setup,Call,Cancel
(1) Reserve Preset: Press【PRESET】
then press one of the number(1-9)to reserve a preset that correspond to the
NUMBER.
*Note: you can setup 9 presets at most by the remote control.
(2) Call Preset: Press the NUMBER(1-9)directly to call the reserved preset.
*Note: It won’ t work if there’ s no preset reserved in the corresponded number.
(3) Remove Preset: Press【RESET】, then press one of the number(1-9)
to remove a preset that correspond to the NUMBER.
FAR
NEAR
MANUAL
FOCUS
AUTO
FOCUS
ZOOM
SLOW
+
-
ZOOM
FAST
+
-
1 2 3
4 5 6
7 8 9
PRESET 0RESET
STD REV
POSITION
Camera Address set
Dial-up ON/OFF set
Protocol Baud rate COM IR IR Add.
COM
RS-232
SW2 DIP-4
OFF
RS-485 ON
Baud
9600
SW2 DIP-3
OFF
38400 ON
Protocol
VISCA OFF
OFF ON
ON OFF
OFF
PELCO-D
PELCO-P
SW2 DIP-1 SW2 DIP-2
PTZ Add.
1 ON
ON ON ON ON ON ON ON ON
OFF
OFF OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFFON
SW1 DIP-1 SW1 DIP-2 SW1 DIP-3 SW1 DIP-4 SW1 DIP-5 SW1 DIP-6 SW1 DIP-7 SW1 DIP-8
2
255
....
IR Add. SW2 DIP-5 SW2 DIP-6
All OFF OFF
1OFF ON
2ON OFF
3ON ON
★Attentions for Remote Control
1. If remote control doesn't work, please replace batteries.
2. If there is an object between remote control and specialized remote control sensor, the camera will not work.Please
make sure the remote control is aimed at the sensor which in front of the camera when controlling it.
3 L/R SET and Menu keys are not applicable for this model.
4 Fast zoom key, slow zoom key, manual and auto focus keys not applicable for fixed focus model.
1 2 3 4 5
ON DIP
SW1
6 7
DIP
8 1 2 3 4 5
ON DIP
SW2
6

PS: RS-422/485 and RS232 Pins distribution
1.Control Interface
(1)RS485 Interface Distribution
(2)RS-232 Interface Distribution
PIN NUM
A
B
DTR IN+(connect to RS-485)
DSR IN+(connect to RS-485)
FUNCTION
VISCA RS-232 IN
1.N.C.
2.N.C.
3.TXD
4.GND
5.RXD
6.N.C.
7.N.C.
8.N.C.
1.N.C.
2.N.C.
3.TXD
4.GND
5.RXD
6.N.C.
7.N.C.
8.N.C.
VISCA RS-232 OUT
4
4
6
Table of contents
Other Nugens IP Camera manuals
Popular IP Camera manuals by other brands

Allied Vision Technologies
Allied Vision Technologies Pearleye P-007 LWIR Technical manual

Cisco
Cisco CIVS-IPC-6400 quick start guide

Honeywell
Honeywell iPCAM-WI Camera quick start guide

Securitytronix
Securitytronix ST-IP-TD1.4-B/W quick start guide

Samsung
Samsung GV-CLRIRH - GV-CLRIRH Day/Night Bullet IR... Product specifications

Pulnix
Pulnix TM-745i Operation manual