Numatic TTB 4055 User manual

Owner Instructions
Original instructions
Warning! Read instructions before using the machine
www.numatic.com
TTB 4055/100T
Scrubber Dryer

2
Index
Machine overview
Control panel overview
Rating label / Personal Protective Equipment / Recycling
Safety Precautions
Quick set-up guide
Machine set-up
Emergency Stop
Fitting the brushes
Tipping the brush deck
Fitting and lowering the oor-tool
Filling the clean-water tank
Control of Substances Hazardous to Health (COSHH)
Machine Operation
Pre-cleaning advice
Pre-scrub mode
Floor-tool in use / Break away feature
Setting the cleaning controls
Brush overload (Over Current)
Moving the machine
Regular Maintenance
Emptying top (Waste) tank
Separator / Waste basket removal and cleaning
Emptying the bottom (Clean Water) tank and cleaning the clean water lter
Changing the oor-tool blades
Page 2
Page 3
Page 4
Page 5
Page 6 / 7
Page 8
Page 10
Page 10
Page 10
Page 11
Page 11
Page 11
Page 12
Page 12
Page 12
Page 13
Page 13
Page 14
Page 15
Page 15
Page 15
Page 16
Before continuing, please refer to Quick Set Up Guide on Page 8
!
Machine Charging
Battery care
Charger viewing window / Sequence
Hour meter
Specications
Wiring diagrams
Trouble shooting
Recommended spare parts
Declaration document
Warranty
Company addresses
Page 17
Page 17 / 18
Page 18
Page 19
Page 20
Page 21
Page 21
Page 22
Page 23
Page 24

3
Machine Overview
1
4 5
6
78
2
3
12
14
15 16
17
18
19
20
21
13
1. Fuse
2. Operator control panel ( see page 4 )
3. Emergency Stop
4. Separator
5. Waste-water tank
6. Clean-water tank
7. Brush deck
8. Clean-water lter
9. Free wheel lever
10. Rear moving wheels
11. Clean Water On / Off tap
12. Floor-tool vacuum hose
13. Vacuum hose
14. Top tank (waste water) drainage hose
15. Clean-water ller cap and hose
16. Clean-water level indicator / Drainage Hose
17. Floor-tool lifting lever.
18. Hour Meter
19. Isolator Key
20. Floor-tool retaining knobs
21. Squeegee blades
22. Deck Locking Mechanism
2
34
5
6
78
9
10 11
14
16
20
22

4
Control Panel Overview
For full easy to follow
Instructions on control panel set up and use, see machine operation set-up page 13.
Water Flow On / Off Button
8
7Cycle sequence button
4Vacuum Indicator
1Battery Charge Level Indicator
9Handle Position Lever
3Brush Operation / Load Indicator
5Water Flow Indicator
9
1 2 3 4
67
5
8
1111
On / Off Switch
10
2Hi / Lo Indicator
10
On / Off Trigger
11
6Hi / Lo Button
Charging Point
12
12
13
13 Emergency Stop
14
14
Fast Moving Lever
14

5
Rating Label
WEEE (Waste, Electrical and Electronic Equipment)
Scrubber dryer Accessories and packaging should be sorted for environmentally-friendly recycling.
Only for EU countries.
Do not dispose of scrubber-dryer into household waste.
According to the European Directive 2002/96/EC on waste electrical electronic equipment and its
incorporation into national law.
Scrubber-dryers that are no longer suitable for use must be separated, collected and sent for
recovery in an environmentally-friendly manner.
Safety Critical Component:
Charging Lead: H05VV-F x 1.0 mm2 x 3 core
Battery Charger: 220 - 240 Volt (50/60 Hz)
About the Machine
1
2
3
4
5
6
7
8
9
1
2
3
4
56
7
8
9
Company Name & Address
Machine Description
Voltage Frequency
Power rating
Max Gradient
Weight (ready to use)
CE Mark
WEEE Logo
Splash Proof Rating
Machine yr/wk Serial number
Failure to rectify the problem or in the event of a breakdown contact your Numatic dealer or the
Numatic Technical help line [phone]
10
10
11
12
13
11
12
13
Machine Description
Noise Rating
Hand Arm Vibration
Ear Protection Safety Footwear Head Protection Safety Gloves
Dust/Allergens
Protection
Eye Protection Protective
Clothing
Hi-Vis Jacket Caution
Wet Floor Sign
Note:
A risk assessment should be conducted to determine which PPE should be worn.
PPE
(Personal protective equipment) that may be required for certain operations).

6
As with all electrical equipment care and attention must be exercised at all times during its use, in addition
to ensuring that routine and preventative maintenance is carried out periodically in order to ensure its safe
operation.
Failure to carry out maintenance as necessary, including the replacement of parts to the correct standard could render
this equipment unsafe and the manufacturer can accept no responsibility or liability in this respect.
When ordering spare parts always quote the Model Number / Serial Number specied on the Rating Plate.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This machine is not suitable for picking-up hazardous dust.
Do not use on surfaces having a gradient exceeding that marked on the appliance.
The machine is not to be stored outdoors in wet conditions.
This machine is for indoor use only.
Read the instruction manual before using the appliance.
This product meets the requirements of IEC 60335-2-72
NOTES
This machine is also suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and
ofces for other than normal housekeeping purposes.
• Ensure only competent persons unpack/assemble the machine.
• Keep your machine clean.
• Keep your brushes in good condition.
• Replace any worn or damaged parts immediately.
• Regularly examine the power cord for damage, such as cracking or ageing. If damage is found,
replace the cord before further use.
• Only replace the power cord with the correct Numatic approved replacement parts.
• Ensure that the work area is clear of obstructions and / or people.
• Ensure that the working area is well illuminated.
• Pre-sweep the area to be cleaned.
• Use steam cleaners or pressure washers to clean the machine or use in the rain.
• Attempt machine maintenance or cleaning unless the power plug has been removed from the supply
outlet.
• Allow any inexperienced repairs. Call the experts.
• Strain cable or try to unplug by pulling on cable.
• Leave the brush pad on the machine when not in use.
• Allow the machine to be used by inexperienced or unauthorised operators or without appropriate training.
• Use the machine without the solution tanks properly positioned on the machine, as shown in the instructions.
• Expect the machine to provide trouble-free, reliable operation unless maintained correctly.
• Lift or pull the machine by any of the operating triggers - Use the main handle.
• Remove the handle from the machine except for service and repair.
• Use on surfaces having a gradient exceeding that marked on the machine.
ORIGINAL INSTRUCTIONS
READ MANUAL BEFORE USE
Information for Scrubber Dryer
Component Interval Inspect for
Charging Lead DAILY Scufng, cracks, splits, conductors showing
Brushes DAILY Bristle damage, wear, drive collar wear
Squeegee Blade BEFORE EACH USE Wear, cracks, splits
Filters BEFORE EACH USE Clogging and debris retention
Tanks AFTER EACH USE Rinse dirty water tank after use
WARNING
CAUTION
DO
DON’T

7
Only use brushes provided with the appliance or those specied in the instruction manual.
The use of other brushes may impair safety.
A full range of brushes and accessories are available for this product.
Only use brushes or pads which are suitable for the correct operation of the machine for the specic task being
performed.
It is essential that this equipment is correctly assembled and operated in accordance with current safety regulations.
When using the equipment always ensure that all necessary precautions are taken to guarantee the safety of the
operator and any other persons who may be affected.
Wear non-slip footwear when scrubbing. Use a respiratory mask in dusty environments.
The machine, while charging, must be positioned so that the mains plug is easily accessible.
When cleaning, servicing or maintaining the machine, replacing parts or converting to another function the power
source shall be switched off.
Mains operated machines shall be disconnected by removing the power plug, and battery operated machines shall be
disconnected by switching off the isolating key.
Machines left unattended shall be secured against unintentional movement.
Operators shall be adequately instructed as to the correct use of the machine.
WARNING
1. Always wear protective clothing e.g. Face visor, gloves and overalls when working with batteries.
2. Whenever possible always use a properly designated and well-ventilated area for charging. Do not smoke or bring
naked ames into the charging area.
3. Remove any metallic items from hands, wrists and neck i.e. Rings, chains etc. before working on a battery.
4. Never rest tools or metallic objects on top of the battery.
5. When charging is complete disconnect from the mains supply.
6. The batteries must be removed from the machine before it is scrapped.
7. The machine must be disconnected from the supply when removing the battery.
8. The batteries are to be disposed of safely and in accordance with the battery directive.
9. Only use genuine Numatic replacement batteries.
10. Do not allow the batteries to become fully discharged; it may not be possible to recharge them.
11. Do not allow one battery to be discharged separately to the other.
12. Do not mix batteries from different machines.
13. The batteries tted to this product are Valve Regulated Lead Acid (VRLA) gel electrolyte type. The tting of any
other type of battery may cause a safety hazard.
PRECAUTIONS WHEN WORKING WITH BATTERIES
1. Always recharge the batteries after use. This can be done at any time its not necessary to wait until they are fully
discharged; they do not develop a “memory”.
2. Leaving the charger to operate for a minimum of 4 hours after the green light has come on, at least weekly, will
prolong battery life.
3. Do not store the machine with the batteries discharged.
BATTERY CARE
Daily
Keep the machine clean
Ensure brushes/ pads/ squeegee/ lters are in good condition
Check for any worn or damaged parts and replace immediately
Drain and rinse dirty water tank after every use
Store machine with brush deck secured in tilted position
Weekly – as daily and –
Check brush or pad and skirt and rinse
Check oor tool blades for wear and wipe clean
Clean separator assembly including lter and check condition of seal
Flush out system with clean water and clean lters
Do not steam clean or pressure wash
Batteries
Always recharge the batteries after use
Charge for a minimum of 4 hours after the green light has come on as this will prolong battery life
Twin Tec
Maintenance

8
PLEASE READ BEFORE COMMENCING ANY OPERATION.
After the removal of all the packaging, carefully open and check the contents.
Ensure the Batteries are charged before use.
!!
1Using the handle position lever
(Fig.1), move the handle into the
upright position (Fig.2).
4Fit the isolator key and switch the machine on (Fig.7).
Fig.1
Quick Set-Up Guide
2Place 50 amp fuse (supplied in the accessory kit) into the fuse holder using
the Maxi Fuse puller provided (Fig.3).
Fig.3
Place the top tank (waste water) into the machine (Fig.5) and connect the
vacuum and oor tool hose (Fig.6).
3
Fig.5
Fig.2
Fig.6
Fig.7
Fig.4
(Fig.4) shows 50 Amp fuse
5Fill the bottom tank (Clean Water) from a tap or hose pipe using the Flexi-Fill pipe tted to
the ller cap (Fig.8). Add non-foaming cleaning uid as required (See page 11).
The TTB 4055/100T has a water capacity of 40 Litres.
Fig.8
Note:
Great care must be taken to ensure that contaminants
(leaves, hair, dirt, etc.) are not allowed to enter the
clean-water tank during the lling process.
If using a bucket or similar, ensure it is always clean
and free from debris.

9
6Fit the Brush / Pad (Fig.9).
Push in the deck
locking pin (Fig.10)
and rotate the
brush deck into
the operating
position (Fig.11).
Fig.9
7Turn on the clean water tap
(Fig.12). 8
To start: hold either trigger and
press the yellow start button once
to start the machine. (Fig.13).
Brush, vacuum and water settings
can be controlled from the control
panel (See Page 13).
Fill the clean-water to a Max of 40 litres (see page 10)
For operation and cleaning controls (see page 14)
Fig.12 Fig.13
Fig.10
Fig.11
9Fig.14
10
Fig.15
Hold down either trigger to make the machine move.
For a speed boost when moving the machine press the grey thumb levers
down (Fig.14).
Located on the left side of the machine is the Free Wheel lever.
To disengage the brake / drive mechanism, pull the lever out and move it to
the lower hole position (Fig.17).
This allows the machine to be moved in free wheel mode, for more
information (see page 14).
Note:
When the machine is in free wheel mode the brake has been disengaged,
avoid slopes.
11
Direction is controlled using the
direction switch tted to the left side
of the handle (Fig.15).
The speed is controlled by the
speed control knob tted to the right
hand side of the handle (Fig.16).
Fig.16
Fig.17
12
On
Off

10
Fitting the brushes
Featuring the Nulock brush system.
The brush is simply pushed and twisted to lock, making tting and removal a simple process.
The Pad is retained using Numatic’s own PadLoc system (ask your supplier for details).
Only use manufacturer supplied brushes.
TTB 4055/100T requires a 550mm brush or a 500mm pad.
Safety gloves are recommended for the changing of used brushes.
Machine Set-Up
Fit the brush /pad to the drive chuck,
twist to lock the brush / pad in place
(Fig.19) (Fig.20).
Tipping the Brush Deck
To tip the deck into the down position
(Operating mode) Press in the brush
deck locking bar (Fig.21) and rotate the
brush deck (Fig.22).
To change to brush deck up position,
(Transit mode) simply lift the deck and
the spring loaded locking bar will
activate to hold the deck up.
Fig.20
Fig.22
Fig.21
Fig.19
Important
Do not operate machine unless the Operator Manual has been read and fully understood.
!!
Fig.18
This machine is tted with an Emergency stop button,
instantly stopping the machine if accidentally reversed into the operator (Fig.18).
Emergency Stop

11
Machine Set-Up
Note.
Great care must be taken to ensure that contaminants (leaves, hair, dirt, etc) are not allowed to enter the
clean-water tank during the lling process.
If using a bucket or similar, ensure it is always clean and free from debris.
Control of Substances Hazardous to Health (COSHH)
For best results use a non-foaming type of chemical, dilute to the manufacturers specication.
For further guidance on hazardous substances refer to health and safety instructions online.
Visit http://www.hse.gov.uk/ for UK information.
WHEN HANDLING AND MIXING CHEMICALS.
Always ensure that chemical manufacturer’s safety guidelines are followed.
Only use chemicals recommended for use in auto scrubber-dryers.
!!
Fitting and lowering the Floor Tool
The oor-tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-off
feature if the oor-tool gets snagged, whilst in transit.
Raise the oor-tool for transit or
lower for cleaning operation using
the lifting handle tted to the back of
the machine (Fig.25).
For tting the oor-tool blades
(See Page 16).
Note:
It is easier to t the oor-tool if the weight of the machine is resting on the brush. Ensure the brush is tted rst.
Fig.24
Fig.23
Fig.25
Fit the oor-tool and retain using the
detent pin (Fig.23).
The lifting strap is also held by a
detent pin (Fig.24).
The TTB 4055/100T is equipped with a 40 litre clean-water tank allowing large areas to be cleaning in a single ll.
Filling the clean-water tank
To ll the clean-water tank, use the 1 meter FLEXI
- FILL pipe from either a tap or hose pipe (Fig.26).
The large cap can also be unscrewed for lling
from a bucket or suitable
container.
Fill the clean-water tank to a maximum of 40 litres,
including cleaning chemicals if required.
Follow chemical manufacturing guide lines.
The clear dump hose at the rear of the machine can be used to see the level of the clean water.
Fig.26

12
Pre-cleaning advice.
Before performing the cleaning operation, place out
appropriate warning signs and sweep or dust-mop the oor
(Fig.27).
Numatic part (629044) Wet Floor sign
(available if required)
Machine Operation
Pre-scrub mode
The TTB 4055/100T has been designed to cope with a variety of oor types and different levels of soiling.
On heavily soiled oors use a ‘double scrub’ technique.
First pre-scrub the oor with the oor-tool in the raised position, allow the chemical time to work, then scrub the area a
second time with the oor-tool lowered.
Floor tool in use
The clean-water / chemical mix is dispersed via the ‘THRU-FEED’ system.
The waste water is then retrieved by the oor-tool.
Overlap the scrubbing path by 10cm to ensure an even clean (Fig.28).
If streaking occurs, wipe the oor-tool blades clean (Fig.29).
Fig.28 Fig.29
Fig.27
Ref to (Fig.25) to raise and lower the oor-tool.
Breakaway oor-tool The oor-tool design incorporates a breakaway feature.
Allowing it to safely disengage from its mounting should it
become caught on an obstruction, during forward machine
movement.
To re-attach the blade to its holder.
First loosen the retaining knobs on the oor-tool body and slide
onto the holding bracket.
Tighten retaining knobs to nger tight.
Note: Care must be taken to reduce speed when cornering or when manoeuvring around obstacles.
Note: The machine will still reverse with the oor-tool in the lowered position, this could possibly damage the blades.
Raise the oor-tool before reversing.

13
Brush overload.
The brush LED light will ash if the brush motor has been
overloaded (Fig.30).
Releasing the handle triggers will allow the machine to stop
and reset.
If the brush motor keeps overloading consider using a different type of brush.
Or move the transit wheels to obtain different brush pressures,
Heavy brush load decreases the available battery run time.
Setting the cleaning controls
Hi / Lo speed can only be toggled when the machine is in
STAND-BY MODE.
Water On / Off can only be toggled when in ACTIVE MODE.
Brush / Vac Switch can be cycled in both
STAND-BY and ACTIVE MODE.
Fig.30
To activate the machine from SLEEP MODE press either trigger
once.
When the triggers are released the brush motor and the cleaning solution pump will switch off, the vacuum motor will
continue for 10 seconds (this is to clear any uid residue in the hose).
The panel if unused will automatically enter SLEEP MODE after 60 seconds.
The TTB 4055T has been tted with a Hi - Lo mode, this reduces the noise produced by the
vacuum motor by 3dB.
To operate the Hi - Lo mode start the machine in the normal way.
When the machine is running normally the Hi - Lo light will NOT be illuminated, this means
the Vacuum motor is running at 100%.
With the machine running press the Hi - Lo button once the Vacuum motor will reduce speed
to 75% of capacity and the Hi - Lo light will illuminate Blue.
STAND-BY
Stage 1. Brush and Vac
Stage 2. Brush only
Stage 3. Vac only
ACTIVE
Stage 1. Brush and Vac
Stage 2. Brush

14
Moving the machine
Free Wheel / Transit Mode
The TTB 4055/100T has a free wheel mode enabling the machine to be moved even when the battery has reached a
low level.
Move the Free Wheel Lever tted to
the left hand side of the
machine to the LOWER position to
enable the machine to be moved
WITHOUT battery power (Fig.31).
Fig.31
Move the Free Wheel lever to the
UPPER to enable the drive
mechanism to be engaged (Fig.32).
Fig.33
Fig.34
Hold down either trigger, to make the machine move (Fig.33).
Pressing either of the moving levers allows the machine to move faster.
Direction is controlled using the direction switch tted to the left side of the
handle (Fig.34).
Fig.35
Fig.32
The speed is controlled by the speed control knob tted to the right hand side
of the handle (Fig.35).
Fig.36
By pressing the emergency button Stops the machine and all its functions.

15
ALWAYS ENSURE THAT THE BATTERY IS DISCONNECTED
PRIOR TO ANY MAINTENANCE OPERATION
! !
After use, empty waste-water tank using
emptying hose and ush-out with clean
water (Fig.37).
Do not attempt to remove top (waste) tank
unless empty.
A
Remove the two hoses to disconnect the separator from the
machine (Fig.38).
Lift off the separator. The separator has a sealing-rubber
which should be examined at every clean-down (Fig.39).
Rinse using clean water.
The TTB 4055T has been designed with ease of use in mind, this included easy stripping-down and cleaning.
Remove the lter tted into the separator and ush with clean water (Fig.40)(Fig.41).
Placed into the top tank is grey lter basket, clean and ush with clean water (Fig.42) (Fig.43).
A
Regular Maintenance
Clean by ushing with clean water if required.
Excess water can be drained using the clear dump hose tted to the rear of
the machine.
Fig.37
Fig.38 Fig.39
Fig.40 Fig.41
Fig.44
Fig.42 Fig.43
Emptying waste tank
Emptying clean water tank
Separator / Filter cleaning
Fig.45
On
Off
Located under the left hand side is a clean
water lter, ensure the clean water tap is
turned off before removing this lter (Fig.45).
Clean and ush with clean water if required.

16
! !
ALWAYS ENSURE THAT THE BATTERY IS DISCONNECTED PRIOR TO ANY
MAINTENANCE
Note:
The blades are designed to be reversible, thus extending their useful working life.
Changing the Floor Tool Blades
The oor-tool
Fig.47 Fig.48
Fig.46
To clean the oor-tool, remove securing-pin and pull-free from the holder, disconnect the lifting strap
(see Page 11).
Rinse the oor-tool assembly with clean water and ret.
Periodically the oor-tool blades should be examined and checked for wear and damage.
The blade removal is easy. Simply start by removing the four retaining pins (see Fig.46), turn the
oor-tool over and separate the blade carrier from the body (see Fig.47).Peel away the blades from their locating
lugs (see Fig.48) and examine or renew as required.
Replacement is a reversal of the removal process.
Floor-tool overview
1. Floor-tool main body
2. Rear blade
3. Blade carrier
4. Front blade (slotted)
5. Retaining pins x 4
1
2
3
4
5
The TTB range is provided with the aluminium oor-tool shown.

17
Machine Charging
To ensure your machine remains at its maximum efciency and prolong your battery life, please follow
the simple steps below:
Under normal daily usage:
Recharge batteries after each use, regardless of
machine operation time.
Connect the charger unit to the
battery (Fig.49). and plug the charger into a suitable
power supply (Fig.50).
Fig.50
Recharge the machine fully after its last use.
Do not leave the machine in a discharged state.
Fig.49
The battery meter displays the charge level of the batteries; when fully charged,
all meter lights are illuminated.
As the machine is used and the batteries are discharged, the meter lights will go out from
top to bottom.
If the battery-charge level is allowed to discharge to the point that only one red light remains
illuminated, the operator should either replace or charge the battery.
The battery supplied with the TTB 4055/100T allows for a run time of 145 mins approx (Hi
Mode), when fully charged.
The battery pack must be fully discharged and recharged over a few cycles and brushes
need to be worn in to achieve maximum efciency.
Charge time is approximately 8 hours for the TTB Range
Spare replacement batteries are available from your supplier.
Remove the top tank to view the charging light panel
located on the pump housing plate.
Once fully charged, disconnect the charging lead from both the power supply and the machine.
Viewing panel for charging-light sequence (Fig.51).
(See page 18) for charging light sequence.
Battery Care
Viewing Panel
Fig.51

18
Under abnormal use; i.e. leaving the machine without charging
for a period of time - we advise that you follow these steps:
If the machine will be standing unused for a period of 30 days
or more, then batteries must be fully charged and battery fuse be
removed using the Maxi fuse-puller provided, prior to this period.
Note:
Batteries should be recharged every three months.
Charge fully the day before you start using the machine again.
Hours Meter
Fitted to the TTB Range is an hour meter allowing you to
monitor the usage of your machine and batteries (Fig.52).
Signal (LED) Meaning
Red LED on First phase of charge in progress
Yellow LED on Second phase of charge in progress
Green LED on
End of charge or maintenance phase
Disconnect from power supply
Switch power supply, Off then On, to restart the
charging cycle
Red LED ashing
Unsuitable battery or charging malfunction
Safety timer exceeded
Internal short circuit
Disconnect from power supply
Switch power supply, Off then On, to restart the
charging cycle
Yellow LED ashing Battery not connected
INITIAL TEST
Green LED with 2 ashes Battery charger congured for recharging Gel or
AGM batteries
Red LED with 2 ashes Battery charger congured for recharging
Lead-acid (Wet) traction batteries
Replace with Numatic approved part (221107) 50 amp fuse.
Fig.52

19
Specications
TTB 4055/100T
Brush Motor Vac Motor Brush Sizes Pad
sizes Weight Protection Class Power
400W 400W 550mm 500mm 142Kg IPX4 2 x 12V (24V) 100Ah
Fluid Flow Speed Recharge time Cleaning
Speed Drive Motor Hand Arm Vibration Noise Size
0-2L/Min 100 rpm 8 hrs 0-5kph 250W 0.59 m/s2Hi-69 dB(A)
Lo-67 dB(A)
Width - 560mm
Length - 1060mm
Height - 1160mm
Off-Aisle Cleaning Kit (Optional Extra Accessory) 606182
Spare Parts
577810 Top Tank (blue) 206727 Wheel
577811 Bottom Tank (blue) 577812 Deck
577839 Separator 577888 Handle
206265 Barrel Filter 321686 Vac Motor
207000 Basket Filter 220386 Charger Cable UK
208588 Vac Hose 221079 Charger Cable Euro
208624 Floor Tool Hose 220622 Charger Cable Switzerland
213047 Dump Hose Top 221107 50 Amp Fuse (Batteries)
303641 Dump Hose Bottom 221037 20 Amp Fuse (Charger)
577922 Floor Tool 206813 Isolator Pin \ Key
606028 550mm Polyscrub Brush 206953 Detent Pin
606550 550mm Nyloscrub Brush 606551 550mm Long Life Brush
606403 500mm Padloc Drive Board
606295 Recommended Linatex Floor Tool Blade Set 606296 Optional Polyurethane Floor Tool Blade Set

20
TTB- 4055/100T
DRW-11389 (A06) 06:11:2012
Wiring Diagram