NUUO SCB-C31A POS User manual

The Point of Sale Solution
SCB-C31A
Hardware & Software Installation
user’s manual
2011, May

Intelligent Surveillance Solution
Table of Contents
page-1
TABLE OF CONTENTS
TABLE OF CONTENTS.................................................................................................. 1
SYSTEM INTRODUCTION ............................................................................................ 2
Definition of Terms.............................................................................................. 2
Product Specification ....................................................................................... 3
HARDWARE INSTALLATION ....................................................................................... 4
SCB-C31A data capture convertor............................................................... 4
SOFTWARE INSTALLATION ......................................................................................... 6
SCB-C31A POS data capture convertor ...................................................... 6
NUUO NVR/DVR/Hybrid system installation.................................................. 7
NUUO NVR/DVR/Hybrid software setup........................................................ 7

Intelligent Surveillance Solution
System Introduction
page-2
SYSTEM INTRODUCTION
NUUO POS, a Point of Sale Systems based on NUUO NVR/DVR/NVDR,
provides financial transaction’s surveillance solution in one central system.
The architecture is as below; POS transaction data flows to NVR by
Ethernet. Each Cash Register with an external receipt printer is connected
by DB9 cable. The transaction information delivered in RS232 format can
be converted to Ethernet through SCB-C31A data capture convertor.
Definition of Terms
Terms
Definition
POS Original Data
Original data from POS. Usually with a lot of symbols and
no line feed.
POS Transaction
Filtered result by user-defined tag-filter.
POS Event Log
Smart Guard Event Log from POS transaction. It includes
Transaction start, Transaction end, Cash register open,
User defined condition. Abbreviation
of POS Log.

Intelligent Surveillance Solution
System Introduction
page-3
Product Specification
NUUO Capture Box
SCB-C31A
Input
RS232
Output
Ethernet
DC In
DC +9V to +24V
Power consumption
500 mA
Operating Temperature
-20 to 65℃
Operating Humidity
0-90 % Non-Condensing
Baud Rate
110 bps to 230.4 kbps
Data Bits
5, 6, 7 or 8
Stop Bits
1, 1.5 or 2
Parity
None, Even, Odd, Mark, Space
Flow Control
None, RTX/CTS, XON/XOFF, DTR/DSR

Intelligent Surveillance Solution
Software Installation
page-4
HARDWARE INSTALLATION
SCB-C31A data capture convertor
To connect Cash Register, Printer, and SCB-C31A POS data capture
convertor together, please follow below steps:
Step 1: Please refer the user manual to setup Cash Register and printer.
Step 2: Using a “Y-shape” DB-9 cable, one DB-9 female connect to POS
system and one DB-9 male connect to the receipt printer
Y-shape (provided by Printer vendor).
Step 3: Using another DB-9 female connect to SCB-C31A POS Data
Capture R232/Ethernet convertor with Null modem.
Note: There are two kinds of serial cable: Straight pass-through
and Null-Modem. The connection between SCB C31A POS Data
capture box and Y-cable must be null modem (in package).
Step 4: Check the system switch of the SCB-C31A POS is switch to OFF,
OFF position.
Step 5: Connect power source with SCB-C31A POS.
Step 6: Connect SCB-C31A POS with internet port by RJ45 LAN cable.

Intelligent Surveillance Solution
System Introduction
page-5
The LED Indicators:
Link LED: Ethernet cable connection and data active.
Run LED: System is ready (Blinking).
Serial 1: Transiting/Receiving Indicator.

Intelligent Surveillance Solution
Software Installation
page-6
SOFTWARE INSTALLATION
SCB-C31A POS data capture convertor
Step 1: Use IE-browser to setup SCB-C31A POS, the default IP address is
192.168.1.1
Step 2: Setup IP address and password, and then setup IP address.
Note: Each time you switch the page of the web, please click
Save at first. If you leave this page without saving, all changes
will be ignored.
Step 3: Setup Password if needed. Password is only using to activate a
security feature on the serial server. Once a password is entered
it will be required to access the menu and make change of
configuration when access.
Note: Please write down the Serial number and MAC address,
these two parameters are necessary when user forget your
password.
Step 4: Setup according to your POS or Cash Register. Usually all
devices are default setting, you can reserve your time to pass
this step.

Intelligent Surveillance Solution
System Introduction
page-7
Step 5: Please restart/reset the box after changing configurations to
active setup.
To reset the unit manually apply power, insert a small plastic tool,
and press lightly depressing reset located between the switch
(refer page 5). Hold for 3 seconds and release. The Link and Run
light will go out and turn back on. The SCB-C31A POS will revert
to the last setting.
Note: Every time you change the configuration of SCB-C31A
POS, please check the above settings, especially maximum
connection and Remote IP address to avoid connection fail.
NUUO NVR/DVR/Hybrid system installation
Please refer to the Main Console user manual to complete system
installation with the NVR/DVR/Hybrid systems installation CD.
NUUO NVR/DVR/Hybrid software setup
Please refer to the Main Console Metadata_Plugins user manual to
complete software setup with the NVR/DVR/Hybrid systems installation
CD.

Intelligent Surveillance Solution
page-8