nuVita Planet Tule 3013 User manual

3013
Instruction manual
Planet
Digital audio baby monitor
EN
3013
Thank you for purchasing NUVITA 3013 TULE AUDIO BABY MONITOR. Your unit has been manufactured and
checked under the strictest possible quality control to ensure that each monitor leaves the factory in perfect
condition. In the unlikely event you nd any defects or have any problem, please contact our dealer or service
center.
Please read this manual carefully to obtain maximum performance and extended service life from the unit.
Nuvita TULE-equipped products can automatically select free channel or hop to free channel during
communication to avoid interference from other electronic devices. In addition, Nuvita TULE techonology
allow our products to detect the signal power between the baby unit and parent unit, then automatically
reduces the emission power from baby unit when the two units are in close vicinity. As a result, the level of
radiation to baby is greatly reduced and always at the minimal level. Nuvita TULE technology helps to protect
the baby’s health for now and future.
DECT and 2.4GHz solution are most common wireless techonlogy applied in baby monitor telecommunication.
DECT is Digital Enhanced Cordless Technology, widely used in household wireless telephones. 2.4GHz solution
is using the 2.4GHz bandwidth for signal transfer. Both DECT and 2.4GHZ were developed for adult use, then
apply to baby monitors. Nuvita TULE, True Ultra Low Emission Technology, is Exclusively Developed for Baby
monitors having in mind that the baby’s health is always our First Priority.
ABOUT NUVITA TULE
The NUVITA 3013 TULE AUDIO BABY MONITOR should not be regarded as a medical device. Premature babies
or those considered to be at risk should be under the supervision of your doctor or health personnel.
Direct supervision of your baby at a regular interval by a responsible adult is strongly recommended in
addition to using the NUVITA 3013 TULE AUDIO BABY MONITOR.
WARNING
The Lithium battery is partially charged and already installed in the unit.
Connect the supplied cable to USB power source. During charging, the POWER indicator will light up RED (
if unit is switched o ) or both RED and GREEN ( if unit is switched on ). Once the battery is fully charged up
PARENT UNIT
1.
2.
Equipped Lithium battery
Charging the Lithium battery
POWER SUPPLY
1.
2.
3.
4.
5.
Full digital technique operating in the 863-870MHz
with zero interference on standby
Automatic hop and search for free channel
Operating range 600m in open space
Low radiating power (only 10% of normal DECT or
50% of ECO DECT)
Night light on baby unit
FEATURES
Low battery alert on both baby and parent unit
Digitally adjustable microphone sensitivity
Audio and visual alert for out of range
Digital volume control
LED sound level meter
Lithium battery installed
6.
7.
8.
9.
10.
11.

BABY UNIT
Slide open the battery door. Insert 3 x AAA size
alkaline batteries (purchase separately) into the
compartment. Observe correct polarities indication.
N.B. For best performance, do not mix use old
and new batteries or alkaline and rechargeable
batteries.
Connect the supplied cable to USB power source,
make sure the polarity is correct. The power supply
from the alkaline battery will be cut o once the
micro-USB plug is inserted into Baby Unit USB port.
1. 2.Power with batteries Operation using USB cable
(normally it takes around 4 hours), the POWER indicator turns
steady RED ( if unit is switched on ) or POWER indicator o (if
unit is switched o). Either you can disconnect the cable or keep
connecting will cause no damage to the battery. In the latter
case, when the battery is being consumed and voltage falls to a
certain level, the Lithium battery will automatically be charged
up again.
Note: Before using the parent unit for the rst time, charge
up the Li polymer battery for at least four hours.
BABY UNITPARENT UNIT
CONTROL LAYOUT
1.
2.
3.
4.
Power ON/OFF switch
Up/Down button
Power/battery low
indicator
LED level meter
5.
6.
7.
8.
Speaker
USB port
Power ON/OFF switch
Up/Down button
9.
10.
11.
12.
Power/battery low
indicator
Transit indicator
Night light switch
Microphone
13.
14.
15.
USB port
Night light
Night light VOX
indicator.
This process is to match the Parent Unit with Baby Unit so that they can communicate with each other while no
other devices (even baby monitor of identical model) can interfere with you or receiving your signal.
The Parent Unit and Baby Unit are already paired when they are manufactured. However, in case you still
encounter interference, perform pairing again to achieve better privacy and signal quality.
PAIRING
1.
2.
3.
4.
5.
6.
7.
8.
Make sure both units are switched o.
Press Hold“DOWN” on button 2 of Parent Unit.
Long Press button 1. The POWER indicator should start FLASHING GREEN. Release both buttons.
Press hold“DOWN” on button 8 of Baby Unit.
Long Press button 7. The POWER indicator should start FLASHING GREEN. Release both buttons.
Press again“DOWN” on button 8 of Baby Unit, if pairing is successful, two beep sound will be heard in
Parent Unit. The POWER indicator of both Baby Unit and Parent Unit should show STEADY GREEN.
The baby monitor is now ready for operation and probably a feedback noise will be heard in speaker of
Parent Unit.
In case the Parent Unit and Baby Unit cannot communicate with each other, repeat pairing process again.
Place the Baby Unit about 1 metre from the crib with
the microphone facing towards the baby. Switch
on the unit by Long Press of button 7, the POWER
indicator will show STEADY GREEN. If this indicator
starts FLASHING GREEN, the battery level becomes
low. Connect the supplied USB cable to a USB power
source.
Adjust the microphone sensitivity using the button
8 to acquire your desirable loudness level. The
TRANSMIT indicator will blink everytime these buttons
are pressed, more number of blinks means the
microphone is more sensitive to sound (maximum is
5 blinks and minimum is 1 blink). Press UP to increase
and DOWN to reduce microphone sensitivity.
Once Baby Unit is in transmit mode, the TRANSMIT
indicator turns RED. The unit will return standby mode
a few seconds after the microphone stops picking up
any sound and the TRANSMIT indicator goes o.
The NIGHT LIGHT (NL) can be set to permanently ON
or VOX mode ( voice activated ) by short press of the
button 11 in following method:
OPERATION
BABY UNIT
NIGHT LIGHT OFF
NIGHT LIGHT ON LEVEL 1
NIGHT LIGHT ON LEVEL 2
NIGHT LIGHT ON LEVEL 3
NIGHT LIGHT ON LEVEL 3 VOX MODE
NIGHT LIGHT OFF
Press button 11
Press button 11
Press button 11
Press button 11
Press button 11
Under VOX mode, the VOX indicator 15 will light up. Once the microphone picks up a sound, the night light will
be on and will fade o automatically a few seconds after the microphone stops picking up any sound.

Clean the Baby Monitor with a slightly damp cloth or with an anti-static cloth.
Never use cleaning agents or abrasive solvents.
Do not clean any part of the product with thinners or other solvents and
chemicals – this may cause permanent damage to the product which is not
covered by the warranty.
Keep the Baby Monitor away from hot, humid areas or strong sunlight, and don’t let it get wet.
If something does go wrong, please do not try to repair it yourself – contact Customer Service for assistance
CLEANING
PARENT UNIT
Switch on the unit by Long Press of button 1. The POWER indicator
will show STEADY GREEN. If this indicator starts FLASHING GREEN, the
battery level becomes low.
Charge up the Li battery using the supplied USB cable.
The LED level meter will show the battery status for around 3 sec while
switching on, then resumes to show the received signal level from
baby unit.
Under normal operation, short press button 1 at any time to show the
battery status on the LED level meter.
Place the Parent Unit at a certain distance away from Baby Unit to avoid feedback. Too short distance will
create a screeching sound at the speaker.
Once the Parent Unit receives a signal, the LEDs in the level meter will light up. The louder the baby’s voice,
the more number of LED will be lighted up. This feature is useful to alert the parents of baby’s cry in case the
volume of speaker is turned low to keep the environment quiet,
The speaker volume can be adjusted using the button 2. The LED level meter will show the setting. More LEDs
light up means higher volume (maximum 5 LED). When no LED lights up, the speaker 5 is totally muted. Press
UP button to increase and DOWN button to reduce volume.
Once the Parent Unit is beyond the communication range of the Baby Unit for over 30 sec, an OUT OF RANGE
alarm will be heard together with all LEDs of level meter start ashing to alert the parents. The alarm will only
go o when the Parent Unit comes back within the communication range of BU.
To turn o the alarm sound, press either UP or DOWN of button 2 . The LEDs of level meter still keep ashing
until the Parent Unit falls within the communication range of BU.
Note: This alarm will also be heard in case the Baby Unit is switched o, or its battery has run down, or
its power is cut o.
Each time button is pressed, a beep tone will be heard to validate your press being recognized by the unit.
Both the Baby Unit and Parent Unit can be carried be around using the belt clip. To remove the clip, follow the
diagram below.
At the end of the product lifecycle, you should not dispose of this product with normal household waste.
Take this product to a collection point for the recycling of electrical and electronic equipment. The symbol on
the product, user’s guide and/or box indicates this. Some of the product materials can be reused if you take
them to a recycling point. By reusing some parts or raw materials from used products you make an important
contribution to the protection of the environment. Please contact your local authorities in case you need more
information on the collection points in your area.The internal battery should be disposed of with the Parent
unit in an environmentally-friendly manner according to your local regulations.
DISPOSAL OF THE DEVICE (ENVIRONMENT)
TROUBLESHOOTING
Baby Unit has no transmission
Always showing low battery alert
Many static noise and interference
Too short communication range
Baby Unit always on
Out-of -range alarm always on
Mic sensitivity is too low
Night light is permanently
switched on
Battery life is short
Battery has run down
Baby Unit is located near other
electrical appliances
Many steel structures between
Baby Unit and Parent Unit
Baby Unit battery has run down
Mic sensitivity is too high
Baby Unit battery has run down
Distance between Baby Unit and
Parent Unit exceeds the operating
range
Pairing is not successful
Battery has run out or USB cable
improperly connected
Battery pack is damaged
Adjust mic sensitivity higher using
up button 8.
Switch o night light
Recharge battery using USB cable
(PU) or replace with new battery
or use USB cable connecting to
5V supply.
Remove the electrical appliances
or re-locate the Baby Unit far away
from source of interference.
Re-locate Baby Unit & PU
Replace with new battery or use
USB cable as power supply
Adjust mic sensitivity lower using
down button 8 such that Baby
Unit become voice activated.
Replace with new battery or
use USB cable connecting to 5V
supply.
Move the Baby Unit and Parent
Unit closer together.
Perform pairing again.
Replace with new battery or check
connection
Replace with new battery pack
PROBLEM POSSIBLE CAUSES SOLUTION

WARRANTY TERMS AND CONDITIONS
1.
2.
3.
1.
2.
The product has undergone aesthetic damage due
to improper use not in accordance with instructions
in the manual.
This product has been modied and/or tampered
with.
The cause of the failure was due to poor
maintenance of the individual components and/
or accessories and/or supplies (e.g. oxidation and/
or scaling due to the retention of water or other
liquids, sediment blocking the sensor, leak of
corrosive liquid from batteries).
Costs related to replacements and/or repair of parts
subject to wear or costs for ordinary maintenance
of the product.
The costs and risks involved in transporting the
product to and from the store where you purchased
The manufacturer, distributor and all the parties
involved in the sale do not assume any liability for losses
and economic damage from any malfunction of the
product. In accordance with current regulations the
manufacturer, distributor and all the parties involved
in the sale are not responding in any case for damages,
including direct, indirect ones, loss of net income, loss
of savings and additional damage and other details
consequences going beyond the damage caused by the
breach of warranty, contract, strict liability, wrongdoing
or due to other causes, resulting from the use or
inability to use the product and/or paper and electronic
documents, including the lack of service.
For further information on the help service visit the
website www.nuvitababy.com
This product benets of a warranty of 24 months on
material and manufacturing defects, starting from the
date of purchase (see sales slip).
The warranty of 24 months does not include damages
caused by the usual use of parties identied as
“consumable”(e.g., batteries, brush heads or parts
subject to usury).
The legal guarantee of 24 months is void if:
The following is excluded from the legal guarantee of
24 months:
or otherwise authorized collection centre to receive
the products under warranty.
Damage caused by or resulting from improper
installation or improper use not in accordance with
the directions in the instruction manual.
Damage due to natural disasters, accidental events
or adverse conditions not compatible with the
product.
Defects that have a negligible eect on product
performance.
3.
4.
5.
Use only the supplied USB cable, use of other cable may cause damage to the NUVITA 3013 TULE AUDIO BABY
MONITOR baby monitor.
When not using the monitor for a long period of time, remove all batteries from the Parent Unit and Baby Unit
to avoid damage due to battery leakage.
Disconnect the USB cable from the 5V supply when the monitor is not to be operated.
The NUVITA 3013 TULE AUDIO BABY MONITOR is best performed within a temperature range of 0°C to +50°C
Do not leave the monitor expose to strong sunlight for a long time or nearby any heat source, moisture and
excessive environment.
Do not open the cabinet, no serviceable parts inside.
PRECAUTIONS
·
·
Baby unit
Parent unit
PACKAGE CONTENTS
USB charging cable x 2
User manual
·
·