NX NX-8100F User manual

NX-8100F v1
HD DRONE WITH FOLDABLE DESIGN & 100M RANGE
USER MANUAL
ENGINEERED
FOR THE NEXT GENERATION™

1
CONTENTS
1.0 WELCOME................................................................................................... 2
1.1 BEFORE YOU GET UP IN THE AIR.................................................................2
1.2 GENERAL SAFETY ...........................................................................................2
2.0 PRODUCT CONTENTS ................................................................................ 3
2.1 PRODUCT OVERVIEW.....................................................................................3
2.2 CONTROLLER OVERVIEW..............................................................................4
3.0 BATTERY SAFETY ........................................................................................ 5
4.0 SETTING UP YOUR NX-8100F .................................................................... 7
4.1 INSTALLING THE BATTERY ............................................................................7
4.2 INSTALLING A MICRO SD CARD...................................................................7
4.3 REMOVING A MICRO SD CARD....................................................................7
4.4 REPLACING ROTOR BLADES.........................................................................8
4.5 INSTALLING ROTOR GUARDS.......................................................................8
4.6 REMOTE CONTROL........................................................................................9
4.7 FLIGHT SAFETY................................................................................................9
4.8 SYNCING YOUR NX DRONE........................................................................10
4.9 FACTORY RESET FUNCTION.......................................................................10
5.0 FLYING YOUR NX DRONE......................................................................... 11
5.1 BASIC FLIGHT ................................................................................................11
5.2 TRIM FUNCTION ...........................................................................................11
5.3 SPEED MODE.................................................................................................12
6.0 CAMERA / VIDEO FEATURES .................................................................... 13
6.1 VIEWING PHOTOS AND VIDEOS................................................................13
6.2 CAMERA MODE ...........................................................................................13
6.3 VIDEO MODE ................................................................................................13
7.0 360O FLIP ................................................................................................... 13
8.0 HEADLESS MODE ..................................................................................... 14
9.0 ONE KEY REVERSE ................................................................................... 14
10.0 EMERGENCY / STOP................................................................................. 15
11.0 DRONE MAINTENANCE ........................................................................... 15
12.0 REPLACEMENT PARTS .............................................................................. 15
13.0 WARRANTY TERMS & CONDITIONS......................................................... 16
14.0 INDEMNITY ............................................................................................... 16
15.0 WARRANTY AND WARRANTY DISCLAIMER ............................................. 16
16.0 LIMITATIONS OF NX LIABILITY ................................................................. 18

2
1.0 WELCOME
Thank You for purchasing an NX Drone, get ready to have the time of your
life! We’re sure your NX Drone will bring you a world of great experience
in the air. Please take the time to read the following Safety Warnings and
operating instructions carefully.
1.1 BEFORE YOU GET UP IN THE AIR
Before you familiarise yourself with the NX Drone, we ask that you read
page 5-6 before you start charging your drone’s battery.
1.2 GENERAL SAFETY
Please familiarise yourself with your local legislation regarding drone usage
before you begin using your NX Drone. Included in the package contents
of your NX Drone are the Australian CASA guidelines, please read them
carefully and understand this information as operating a drone outside of
these guidelines may result in legal issues. NX takes no responsibility for
operation of this product outside of what is legally permissible in your area.
• Do not fly your NX Drone any closer than 30 meters from people, animals
or buildings. Check to make sure you are no closer than 5.5 kilometers
from any airfields or airports. For more information on CASA’s Australian
legislation visit: http://www.casa.gov.au/
• You must not fly your drone higher than 120 meters (400 ft) above the
ground.
• You must only fly during the day and keep your drone within visual line-of
sight.
• For information outside Australia please visit the website of your local
aviation authority.
• Do not attempt to modify the NX Drone or any of its components in any
way, doing so will void your warranty and may affect the operation of the
drone.
• Do not use the NX Drone in any conditions that could affect, damage or
impair your view of the NX Drone.
• Do not use the NX Drone in any conditions that could leave it wet, dusty
or sandy. These elements will damage the components of your NX Drone.
• Please do not attempt to touch the NX Drone when the Remote Control
is powered on, or if the rotor blades are turning.
• When flying your NX Drone, please keep in mind the privacy of others.

3
2.0 PRODUCT CONTENTS
2.1 PRODUCT OVERVIEW
1. Camera
2. Rotor Blades
3. Motor
4. Power Button
5. Battery Release Button
1
2
3
45
6
7
8
1. NX Drone
2. Remote Control
3. Rotor Blades x 4
4. Rotor Guards x 4
5. USB AC Wall Charger
6. USB Charging Cable
7. Screw Driver
8. User Manual
1
2
3
5
4

4
2.2 CONTROLLER OVERVIEW
1. Speed
2. Reverse
3. Left Control Stick (Pulse /
Descend, Yaw Left / Right)
4. One Key Take Off / Landing
5. Emergency Stop
6. Right Control Stick (Forward
/ Backward, Left / Right)
7. Photo
8. Video
9. Headless Mode
10. 360oFlip
11. LED Power ON
12. ON / OFF
1
2
3
4
11
5
6
7
10
9
8
12

5
IMPORTANT INFORMATION - PLEASE READ BEFORE USE
3.0 BATTERY SAFETY
When handled incorrectly, Lithium polymer batteries can be
dangerous and can potentially harm and do damage to persons or
property. NX does not accept any liability for damage to persons or
property if the battery is not correctly charged, stored or protected.
• Always unwind all cables before charging.
• Do not over charge the battery. Once the charging process is
completed, remove the battery from the charger as soon as
possible.
• Only use the included or replacement NX chargers and batteries.
• You must charge the Lithium polymer battery in a safe area away
from flammable materials.
• The battery is only to be charged under adult supervision, do not
leave charging batteries unattended. You should always remain in
constant observation to monitor the charging process and react
immediately to any potential problems that may occur.
• Do not charge the battery in temperatures hotter than 40°C or
colder than 0°C.
• Do not cover the batteries when charging. Do not leave batteries in
direct sunlight.
• After each flight & or crash, please check battery for any damage or
swelling.
• If the battery is damaged, leaking, making noise, punctured or
malformed in any way DO NOT attempt to use it. Please dispose of
the battery immediately and safely in the correct manner.
• Do not bend, puncture, crush or scratch the drone’s battery. Do
not store batteries in your pockets, on your person or in extreme
temperatures.
• After flying/discharging the battery you must allow it to cool to
ambient/room temperature before recharging.
• If at any time during the charge or discharge process the battery
begins to balloon or swell, discontinue charging or discharging
immediately. Quickly and safely disconnect the battery, then place it
in a safe, open area away from flammable materials to observe it for
at least 15 minutes. Continuing to charge or discharge a battery that
has begun to balloon or swell can result in a fire. A battery that has
ballooned or swollen even a small amount must be removed from
service completely.
• Never plug in a battery and leave it to charge unattended overnight.
• Non-compliance with the above warnings may result in the failure of
the battery.

6
PLEASE NOTE: YOUR NX DRONE COMES WITH A CERTIFIED
NX USB AC CHARGING ADAPTER FOR 240v CHARGING OF
YOUR DRONE BATTERY. USE OF A NON NX CERTIFIED USB AC
CHARGING ADAPTER WILL VOID YOUR WARRANTY AND MAY
DAMAGE BOTH YOUR BATTERY AND DRONE.
Connect the drone battery to the charging cable. The light will glow
red indicating charging is in process. The LED on the USB charging
cable will turn off once charging is complete. To keep the battery life
as long as possible, avoid removing the battery from the charging
cable before charging is complete. If you have just finished flying
your NX Drone, please allow the battery to cool down for at least 30
minutes before recharging. When the NX Drone battery has finished
charging it is advised that the battery is removed from the charger as
soon as possible. Overcharging will damage the battery and effect the
flight time. The NX Drone battery can take up to 50 minutes to fully
charge. If the battery has been on charge for any longer than 2 hours
and indicator on the charging cable is not showing that the battery is
charged, please remove the battery from the charger.

7
4.0 SETTING UP YOUR NX-8100F
4.1 INSTALLING THE BATTERY
For detailed instructions on how to install the battery please follow the
steps below.
1. Ensure that the battery is fully charged.
2. Insert the battery into the rear of the drone in the correct orientation
(the tab on the battery should be facing down).
3. Slide the battery all the way in until it securely slots into place.
NOTE:
• Do not force the battery, if the battery does not fit into position, please
check that you have installed the battery in the correct orientation.
4.2 INSTALLING A MICRO SD CARD
If you want to record your flights using the NX Drone's built in camera it is
required that you install a Micro SD Card (not included). It is recommended
that you use a class 10 Micro SD Card, up to 32 GB. To install a Micro SD
Card, please follow the instructions below.
1. With the NX Drone positioned upside down , insert your Micro SD Card
into the slot near the copper contacts ensuring that the text on the
Micro SD card is facing upwards.
2. Press the Micro SD card in until a click is heard and the Micro SD Card
locks in position.
4.3 REMOVING A MICRO SD CARD
To remove your Micro SD Card, follow the instructions below.
1. Press the Micro SD Card in until a click is heard and the card releases.
2. The card will now release and the Micro SD Card will now be removable.

8
4.4 REPLACING ROTOR BLADES
If your rotor blades become damaged or the NX Drone drone is no longer
flying straight, the rotor blades may need to be replaced. To replace the NX
Drone's rotor blades please follow the directions below.
There are two types of rotor blades included with the NX Drone, A blades
(clockwise rotation) and B blades (counter clockwise rotation). The blades
are marked on top showing either A or B. The arms of the drone are also
marked A and B showing what blades each motor is compatible with.
It is important that the rotor blades are installed on the designated motors
or else the drone may not fly and you could potentially burn out the drone's
motors.
To remove and replace the rotor blades, please follow the instructions
below.
1. Remove the black cap from the top of the rotor blade that you want to
replace by using a small flat head screw driver (not included). This will
reveal the securing screw.
2. Remove the rotor blades securing screw by unscrewing counter
clockwise with screw driver (included).
3. Once the screw has been removed gently pull the rotor blade upward to
remove the rotor blade from the motor stem.
4. Get your replacement blade and ensure to identify and match the
correct blade with the motor (A rotor blade to A motor, B rotor blade to
B motor).
5. Place the new rotor blade over the motor stem and press it to ensure it
is locked.
6. Replace and tighten the screw.
7. Replace the black cap by pressing it back into position.
NOTE
• It is important that the correct rotor blades are installed on the correct
motors. If they are installed incorrectly the drone will not fly and you
could potentially burn out the drone’s motors.
• When replacing multiple rotor blades please replace the blades one at a
time to avoid any confusion in reattaching the rotor blades.
4.5 INSTALLING ROTOR GUARDS
Replacing the rotor guards is an option. Installing the rotor guards will
protect your rotor blades and motors against bumps and light crashes.
1. To install the rotor guards please insert the rotor
guards' pegs into the designated holes near the
motors on the NX Drone's arms.

9
4.4 REPLACING ROTOR BLADES
If your rotor blades become damaged or the NX Drone drone is no longer
flying straight, the rotor blades may need to be replaced. To replace the NX
Drone's rotor blades please follow the directions below.
There are two types of rotor blades included with the NX Drone, A blades
(clockwise rotation) and B blades (counter clockwise rotation). The blades
are marked on top showing either A or B. The arms of the drone are also
marked A and B showing what blades each motor is compatible with.
It is important that the rotor blades are installed on the designated motors
or else the drone may not fly and you could potentially burn out the drone's
motors.
To remove and replace the rotor blades, please follow the instructions
below.
1. Remove the black cap from the top of the rotor blade that you want to
replace by using a small flat head screw driver (not included). This will
reveal the securing screw.
2. Remove the rotor blades securing screw by unscrewing counter
clockwise with screw driver (included).
3. Once the screw has been removed gently pull the rotor blade upward to
remove the rotor blade from the motor stem.
4. Get your replacement blade and ensure to identify and match the
correct blade with the motor (A rotor blade to A motor, B rotor blade to
B motor).
5. Place the new rotor blade over the motor stem and press it to ensure it
is locked.
6. Replace and tighten the screw.
7. Replace the black cap by pressing it back into position.
NOTE
• It is important that the correct rotor blades are installed on the correct
motors. If they are installed incorrectly the drone will not fly and you
could potentially burn out the drone’s motors.
• When replacing multiple rotor blades please replace the blades one at a
time to avoid any confusion in reattaching the rotor blades.
4.5 INSTALLING ROTOR GUARDS
Replacing the rotor guards is an option. Installing the rotor guards will
protect your rotor blades and motors against bumps and light crashes.
1. To install the rotor guards please insert the rotor
guards' pegs into the designated holes near the
motors on the NX Drone's arms.
2. To remove the rotor guard, please press the
middle part of rotor guard first, then take the
rotor guard out.
4.6 REMOTE CONTROL
1. Extend the arms of the remote controller.
2. Remove the battery cover on the rear of the remote control by sliding it
downward.
3. Insert 2 x AAA batteries (AAA batteries not included) making sure that
they are in the orientation specified.
NOTE:
• The right arm of the controller is Power ON / OFF.
• By extending the arm lower the controller, will Power On make a beep
sound and the Power Indicator will turn ON.
• Closing the right controller arm will turn off the controller.
4.7 FLIGHT SAFETY
Before flying your NX Drone make sure that you are in a safe setting. CASA
restrictions regarding flying drones require the drone to be no closer than
5.5kms from any airport or airfield while flying. Drones should also not be
flown over populated areas or any closer than 30 meters from vehicles,
people or animals.
It is also required that you check your surroundings before taking off making
sure there are no obstacles or dangers in the area including overhead
power lines and large bodies of water. If there are hazards present in your
intended area of flight, please consider an alternative location.
Battery Cover
2 x AAA 1.5V
Battery

10
4.8 SYNCING YOUR NX DRONE
1. Press the ON/OFF button on the top of the drone to turn the drone on,
the LED light of drone will blink a blue colour (front) and a red colour
(rear).
2. Extend the arms of the controller downwards, the controller will make a
beeping sound and the LED indicator will Power On the controller.
3. Move the left control stick to the upside for 1 second and then move the
left thumb stick to the downside for 1 second, the control will beep and
the LED light of drone will stop blinking. LED will change to solid blue in
front and solid red in rear.
4. Please ensure that the drone is kept on
a flat surface. Press the left and right
control sticks outward and downward
(left stick 7 o'clock and right stick 5
o'clock positions) for 3 seconds. The
Drone blades will start rotating and the
drone is ready to fly.
NOTE:
• Please pair the controller frequency within 5m of the drone to avoid
interference with other signals
4.9 FACTORY RESET FUNCTION
To restore factory default settings, follow the
steps below.
1. Press the Power ON/OFF switch to turn
on the drone.
2. Turn the controller on by moving the
right arm of controller downwards.
3. Sync the drone by following the Syncing
Process as mentioned in the previous
section.
4. Place the drone on a flat surface, and
hold the left and right control sticks
inward & downward (left stick 5 o'clock
and right stick 7 o'clock positions) for
3 seconds. The indicator on the drone
will change from constant light to quick
flashing lights. When the LED light
of the drone remains solid again, this
means that the drone has been reset
successfully.

11
5.0 FLYING YOUR NX DRONE
5.1 BASIC FLIGHT
5.2 TRIM FUNCTION
Trimming is used to balance out your drone if it is drifting when flying. To
adjust the trimming please follow the steps below. You can only use this trim
function when drone is airborne.
1. Make sure that the Remote Control and NX Drone are switched on and
correctly paired.
2. With the right control stick centered,
push down on it, once you hear the stick
button click, release it. (This needs to be
done each time you want to adjust trim
in flight).
3. You can now adjust your trim using your
left/right and up/down on your right
controller stick. PLEASE REFER TO
IMAGES 1-3 on Page 12.
4. To stop trimming, press down on the right control stick again.
Push the right control stick up and
down to fly forward and backwards.
FORWARD AND BACKWARDS
Push the left control stick up to gain
altitude and down to descend
UP AND DOWN
Push the left control stick left and
right to pivot left/right.
ROTATION
Push the right control stick left and
right, to fly left/right.
LEFT/RIGHT FLIGHT

12
When the drone is hovering and
starts to drift to the side, push the
right stick to the left/right until the
drone is stable.
TRIM LEFT/RIGHT FLIGHT
When the drone is hovering in place,
and starts to drift forward, press the
right control stick backwards until it's
stable. If it drifts backwards, press
the right control stick forward until
it's stable.
TRIM FORWARD/BACKWARD
If the drone keeps rotating to the
left, press the left direction stick
to the right until it's stable. If the
drone keeps rotating to the right,
press the left direction stick to the
left until it's stable.
LEFT/RIGHT TRIM
5.3 SPEED MODE
The NX Drone has 3 speed modes .
To cycle through the Speed Modes, use
the speed button on the top left of the
controller.
• Each mode will be identifiable by a series
of beeps.
• Low Speed Mode (Default): One beep
• Medium Speed Mode: Two beeps
• High Speed Mode: Three beeps.
NOTE:
• For beginners it is suggested to operate the drone at Low Speed.

13
6.0 CAMERA / VIDEO FEATURES
6.1 VIEWING PHOTOS AND VIDEOS
To view the recorded footage and videos you will need to connect the Micro
SD card to your computer via either a USB Micro SD card reader or via an
SD card converter if your computer has an SD card reader. (Not provided)
6.2 CAMERA MODE
1. With the drone turned on and paired,
press the Photo button.
2. The remote control will beep once and
the LED lights of drone will blink once to
indicate that a photo was taken.
6.3 VIDEO MODE
1. With the drone turned on and paired,
press the Video button.
2. The remote control will beep once and
the LED lights on the drone will blink
continuously to indicate that a video is
being recorded.
3. Press the video button again to stop
recording and the LED lights on the
drone will stop blinking.
NOTE:
• If there is no SD card or the SD card is full, the camera LED's will blink
green.
7.0 360O FLIP
Fly the drone to a height of more than 3 meters, push the right controller
stick in the direction you want to flip your drone, then press the 360odegree
flip button on the top right of your controller to flip your drone.
NOTE:
• 360o degree flips work better when the battery is fully charged.

14
8.0 HEADLESS MODE
1. Press the headless mode button on
the controller (shown in the diagram
to the right). The remote control will
start beeping once indicating that
headless mode has been enabled. To
stop headless mode, press the headless
mode button again; the controller will
beep again.
2. When headless mode is enabled, the drone will move in the direction
that the remote controller stick is pressed, regardless of its orientation.
This makes it easy to bring the drone home when it is far away from you.
3. When using headless mode, the camera of the drone must point in the
direction of flight; the back of the drone should be facing the pilot. See
below.
9.0 ONE KEY REVERSE
1. While the drone is in flight, press the
reverse button on the remote control,
the controller will beep once and the
drone will fly in reverse.
2. Press the reverse button again to cancel
or push the right control stick in any
direction to stop this function.
NOTE:
It is highly recommended that you push the reverse button only when you
are aware that it is safe to reverse.
The correct take off position. The incorrect take off position.
The correct take off position. The incorrect take off position.

15
10.0 EMERGENCY / STOP
1. While the drone is airborne and
emergency is activated , the rotor
blades will lock and the drone will fall to
the ground.
NOTE:
• It is highly recommended that you do not push this button unless it is an
emergency.
11.0 DRONE MAINTENANCE
Avoid exposing your NX Drone and its accessories to dust, sand and
moisture as these can damage the NX Drone. If the NX Drone is exposed to
dust or sand, use a soft brush to remove any visible particles.
12.0 REPLACEMENT PARTS
We understand that it’s not always easy learning how to fly a drone, and
sometimes a close call can turn into a crash landing. For all spare part
enquiries please contact our customer service team on [phone]
or visit our website www.nx-tech.com.au.

16
13.0 WARRANTY TERMS & CONDITIONS
Our goods come with guarantees that cannot be excluded under
the Australian and New Zealand Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
This warranty is provided in addition to your rights under the Australian &
New Zealand Consumer Law.
NX warrants that this product is free from defects in material and
workmanship for a period of 12 months from the date of purchase or for the
period stated on the packaging. This warranty is only valid where you have
used the product in accordance with any recommendations or instructions
provided by NX.
This warranty excludes defects resulting from alterations of the product,
accident, misuse, abuse or neglect.
In order to claim the warranty, you must return the product to the retailer
from which it was purchased or if that retailer is part of a National network,
a store within that chain, along with satisfactory proof of purchase. The
retailer will then return the goods to NX. NX will repair, replace or refurbish
the product at its discretion. The retailer will contact you when the product
is ready for collection. All costs involved in claiming this warranty, including
the cost of the retailer sending the product to NX, will be borne by you.
NX Address: 115-119 Link Road, Melbourne Airport Australia
Ph: [phone]
Email: [email protected]
14.0 INDEMNITY
YOU AGREE TO DEFEND, INDEMNIFY AND HOLD HARMLESS NX AND
ITS SUBSIDIARIES AND AFFILIATES FROM AND AGAINST ANY AND
ALL CLAIMS, PROCEEDINGS, INJURIES, LIABILITIES, LOSSES, COSTS
AND EXPENSES (INCLUDING REASONABLE LEGAL FEES), INCLUDING
BUT NOT LIMITED TO, CLAIMS ALLEGING NEGLIGENCE, INVASION
OF PRIVACY, COPYRIGHT INFRINGEMENT AND/OR TRADEMARK
INFRINGEMENT AGAINST NX AND ITS SUBSIDIARIES AND AFFILIATES
OR THE NX SERVICES, RELATING TO OR ARISING OUT OF YOUR
BREACH OF ANY PROVISION OF THESE TERMS, YOUR MISUSE OF THE
NX OR NX SERVICES, OR YOUR UNAUTHORIZED MODIFICATION OR
ALTERATION OF PRODUCTS OR SOFTWARE.
15.0 WARRANTY AND WARRANTY DISCLAIMER
NX HAS A LIMITED WARRANTY ON WHEREBY NX WARRANTS TO
AND ONLY TO YOU THAT NX DRONES WILL BE FREE FROM DEFECTS
IN MATERIALS AND WORKMANSHIP FOR ONE (1) YEAR FROM THE
DATE OF YOUR PURCHASE OF THE NX DRONE (UNLESS A LONGER
WARRANTY PERIOD IS REQUIRED BY LAW).

17
THE SPECIFICS OF THIS NX LIMITED WARRANTY ARE AT HTTPS://WWW.
NX-TECH.COM.AU/WARRANTY
TO THE EXTENT POSSIBLE UNDER GOVERNING LAW, OTHER THAN
THE ABOVE PRODUCT WARRANTY FOR THE NX DRONES, YOU
UNDERSTAND AND AGREE THAT THE NX SERVICES ARE PROVIDED ON
AN "AS IS" AND "AS AVAILABLE" BASIS. NX MAKES NO WARRANTY
THAT THE NX SERVICES WILL MEET YOUR REQUIREMENTS OR THAT
USE OF THE NX SERVICES WILL BE UNINTERRUPTED, TIMELY, SECURE
OR ERROR-FREE NOR DOES NX MAKE ANY WARRANTY AS TO THE
ACCURACY OR RELIABILITY OF ANY INFORMATION OBTAINED
THROUGH THE NX SERVICES (INCLUDING THIRD PARTY CONTENT),
THAT ANY DEFECTS IN THE NX SERVICES WILL BE CORRECTED OR THAT
THE NX PRODUCTS OR NX SERVICES WILL BE COMPATIBLE WITH ANY
OTHER SPECIFIC HARDWARE OR SERVICE. FURTHER, NX DOES NOT
WARRANT THAT THE NX SERVICES OR THE NX SERVERS THAT PROVIDE
YOU WITH DATA AND CONTENT ARE FREE OF VIRUSES OR OTHER
HARMFUL COMPONENTS. NX ALSO ASSUMES NO RESPONSIBILITY FOR
AND SHALL NOT BE LIABLE FOR ANY DAMAGES CAUSED BY VIRUSES
THAT MAY INFECT YOUR NX DRONES, COMPUTER SOFTWARE, OR
OTHER HARDWARE.
IF YOU WANT INSURANCE TO PROTECT AGAINST ANY RISK OF LOSS
OF YOUR DRONE OR DAMAGE TO YOUR PROPERTY AS A RESULT
OF USING YOUR DRONE, YOU WILL PURCHASE IT. IN THE EVENT OF
ANY LOSS, DAMAGE OR INJURY, YOU WILL NOT LOOK TO NX TO
COMPENSATE YOU OR ANYONE ELSE. YOU RELEASE AND WAIVE FOR
YOURSELF AND YOUR INSURER ALL SUBROGATION AND OTHER RIGHTS
TO RECOVER AGAINST NX ARISING AS A RESULT OF THE PAYMENT OF
ANY CLAIM FOR LOSS, DAMAGE OR INJURY.
NX’S EQUIPMENT AND SERVICES DO NOT CAUSE AND CANNOT
ELIMINATE OCCURRENCES OF CERTAIN EVENTS, INCLUDING, BUT
NOT LIMITED TO, ACCIDENTS OR PROPERTY DAMAGE. NX MAKES NO
GUARANTEE OR WARRANTY, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
THAT THE NX EQUIPMENT AND SERVICES PROVIDED WILL DETECT OR
AVERT SUCH INCIDENTS OR THEIR CONSEQUENCES. NX DOES NOT
UNDERTAKE ANY RISK THAT YOU OR YOUR PROPERTY, OR THE PERSON
OR PROPERTY OF OTHERS, MAY BE SUBJECT TO INJURY OR LOSS IF
SUCH AN EVENT OCCURS. THE ALLOCATION OF SUCH RISK REMAINS
WITH YOU, NOT NX.
OTHER THAN THE ABOVE PRODUCT WARRANTY FOR THE NX DRONES,
NX AND ITS SUPPLIERS DISCLAIM ALL WARRANTIES OF ANY KIND,
WHETHER EXPRESS, IMPLIED, OR STATUTORY, REGARDING THE NX
EQUIPMENT AND ANY ASSOCIATED APP/SERVICE. INCLUDING ANY
IMPLIED WARRANTY OF TITLE, MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD PARTY
RIGHTS. BECAUSE SOME JURISDICTIONS DO NOT PERMIT THE

18
EXCLUSION OF IMPLIED WARRANTIES, THE LAST SENTENCE OF THIS
SECTION MAY NOT APPLY TO YOU. NX HEREBY FURTHER EXPRESSLY
DISCLAIMS ALL LIABILITY FOR ANY CLAIMS FOR SERVICE FAILURES
THAT ARE DUE TO NORMAL PRODUCT WEAR, PRODUCT MISUSE,
ABUSE, PRODUCT MODIFICATION, IMPROPER PRODUCT SELECTION OR
YOUR NON-COMPLIANCE WITH ANY AND ALL APPLICABLE FEDERAL,
STATE OR LOCAL LAWS. THIS WARRANTY AND WARRANTY DISCLAIMER
GIVE YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER
RIGHTS THAT VARY BY STATE, PROVINCE, OR COUNTRY. OTHER THAN
AS PERMITTED BY LAW, NX DOES NOT EXCLUDE, LIMIT OR SUSPEND
OTHER RIGHTS YOU HAVE, INCLUDING THOSE THAT MAY ARISE
FROM THE NONCONFORMITY OF A SALES CONTRACT. FOR A FULL
UNDERSTANDING OF YOUR RIGHTS YOU SHOULD CONSULT THE LAWS
OF YOUR STATE, PROVINCE, OR COUNTRY. FOR OUR AUSTRALIAN
CUTOMERS: PLEASE NOTE THAT THIS WARRANTY IS IN ADDITION TO
ANY STATUTORY RIGHTS IN AUSTRALIA IN RELATION TO YOUR GOODS
WHICH, PURSUANT TO THE AUSTRALIAN CONSUMER LAW, CANNOT BE
EXCLUDED.
16.0 LIMITATIONS OF NX LIABILITY
UNDER NO CIRCUMSTANCES WILL NX BE LIABLE IN ANY WAY FOR ANY
CONTENT, INCLUDING, BUT NOT LIMITED TO, THE LOSS OF CONTENT,
ANY ERRORS OR OMISSIONS IN ANY CONTENT, OR ANY LOSS OR
DAMAGE OF ANY KIND INCURRED IN CONNECTION WITH USE OF
OR EXPOSURE TO ANY CONTENT POSTED, EMAILED, ACCESSED,
TRANSMITTED, OR OTHERWISE MADE AVAILABLE VIA THE NX APP.
NX LIABILITY FOR DAMAGES, ESPECIALLY FOR BREACH OF DUTY
OR OBLIGATION, DELAY IN PERFORMANCE, NON-PERFORMANCE,
OR MALPERFORMANCE SHALL BE PRECLUDED, EXCEPT WHEN
THESE ARE DUE TO NEGLIGENT BREACHES OF ANY SIGNIFICANT
CONTRACTUAL DUTY OR OBLIGATION ON THE PART OF NX. ANY
LIABILITY FOR NEGLIGENCE IS LIMITED TO DIRECT LOSSES USUALLY
AND TYPICALLY FORESEEABLE IN SUCH CASE. SHOULD THE CLAIM
FOR DAMAGES BE BASED ON WILFUL OR GROSSLY NEGLIGENT
BREACH OF CONTRACTUAL DUTY OR OBLIGATION ON THE PART OF
NX, THE PRECLUSION AND LIMITATION OF LIABILITY MENTIONED
IN THE PRECEDING SENTENCES WILL NOT APPLY. THE PRECEDING
PRECLUSION AND LIMITATION OF LIABILITY WILL ALSO NOT APPLY TO
CLAIMS FOR DAMAGES ARISING OUT OF LOSS OF LIFE, BODILY INJURY
OR HEALTH IMPACTS FOR WHICH NX MAY BE LIABLE, OR FOR NON-
CONTRACTUAL LIABILITY.
SOME STATES AND COUNTRIES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. ADDITIONALLY, THIS PROVISION IS NOT INTENDED TO LIMIT
NX'S LIABILITY IN THE EVENT OF NX'S WILLFUL OR INTENTIONAL
MISCONDUCT.