NXP Semiconductors MAC57D5xx Series User manual

1 Introduction
This user guide details the setup and configuration of the NXP
MAC57D5xx Mother Board (MB) Customer Evaluation
Board (hereafter referred to as the EVB) and its daughter cards
(208 LQFP and 516 BGA).
The EVB is intended to provide a low cost mechanism for
customer evaluation of the MAC57D5xx family of
microcontrollers, and to facilitate hardware and software
development. The EVB is intended for bench / laboratory use
and has been designed using ambient temperature specified
components. Two daughter cards are available which connect
to the EVB via high-density connectors. Please consult your
NXP representative for more details.
This product contains components that may be damaged by
electrostatic discharge. Observe precautions for handling
electrostatic sensitive devices when using this EVB and
associated microcontroller.
2 Device overview
MAC57D5xx Family
The MAC57D5xx family is the next generation platform of
devices specifically targeted to the instrument cluster market
using single and dual high resolution displays.
Freescale Semiconductor Document Number: MAC57D5xxUG
User Guide Rev. 0, 05/2016
MAC57D5xx Customer Evaluation
Boards
© 2016 Freescale Semiconductor, Inc.
Contents
1 Introduction.............................. .............................. 1
2 Device overview MAC57D5xx Family...................1
3 Definitions, acronyms, and
abbreviations........................................................... 2
4 MAC57D5MB – Evaluation Board
features.................................................. ..................3
5 Initial configuration.................................................4
6 MCU power supply jumpers............ .......................7
7 Reset control and Oscillators................................ 10
8 Debug connectors....................... .......................... 11
9 Communications interfaces............ ...................... 13
10 Graphics display and video interfaces...................15
11 User interface (I/O)............................................... 19
12 Jumper Default Configuration...............................22

Leveraging the highly successful MPC56xxS product family, NXP is introducing a multi-core architecture powered by ARM
Cortex-M (for real time) and Cortex-A processors (for applications and HMI), coupled with 2D Graphics Accelerators
(GPU), Head Up Display (HUD) Warping Engine, Dual TFT display drive, integrated Stepper Motor Drivers and a powerful
I/O processor, that will offer leading edge performance and scalability for cost-effective applications.
Powered by ARM®Cortex®-M and Cortex-A processors, coupled with 2D graphics accelerators, HUD warping engine,
Dual TFT display drive, integrated Stepper Motor Controller and a powerful I/O processor, these products offer leading
performance and scalability for cost-effective applications.
The family supports up to 2 WVGA resolution displays, including one with in-line Head up Display (HUD) warping
hardware. Graphics content is generated using a powerful Viviane GPU supporting OpenVG1.1, and the 2D Animation and
Composition Engine (2D-ACE), which significantly reduces memory footprint for content creation. Embedded memories
include up to 4 MB Flash, 1 MB SRAM with ECC and up to 1.3 MB of graphics SRAM without ECC. Memory expansion is
available through DDR2 and SDR DRAM interfaces while two flexible QuadSPI modules provide SDR and DDR serial
Flash expansion. In response to the growing desire for security and safety, MAC57D5/4xx family integrates NXP’s latest
SHE-compliant CSE2 engine and delivers support for ISO26262 ASIL-B functional safety compliance.
Figure 1. Block diagram
•Block Diagram shows the maximum configuration!.
• Not all pins or all peripherals are available on all devices and packages.
• Rerouting options are not shown.
3 Definitions, acronyms, and abbreviations
The following list defines the abbreviations used in this document.
Table 1. List of abbreviations
Abbreviations Extension
CMOS Complementary Metal Oxide Semiconductor
CPU Central Processing Unit
CSI Camera Sensor Imaging
DDR Double Data Rate
EEPROM Electrically Erasable Programmable Read Only Memory
Table continues on the next page...
Definitions, acronyms, and abbreviations
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
2 Freescale Semiconductor, Inc.

Table 1. List of abbreviations (continued)
Abbreviations Extension
EPROM Erasable Programmable Read Only Memory
GPIO General Purpose Input/Output
GPO General Purpose Output
I2C Inter-Integrated Circuit
I/O Input/Output
JTAG Joint Test Access Group
LAN Local Area Network
LCD Liquid Crystal Display
LED Light Emitting Diode
MB Megabyte
MCU Microcontroller Unit
PC Personal Computer
PCB Printed Circuit Board
PHY Physical interface
POR Power on Reset
PWR Power
PWM Pulse Width Modulation
QVGA Graphics Adapter
RAM Random Access Memory
SD SanDisk (Smart Media)
SDRAM Synchronous Dynamic Random Access Memory
SI System International (international system of units and measures)
TFT Thin Film Transistor
UART Universal Asynchronous Receiver/Transmitter
USB Universal Serial Bus
HW Hardware
SW Software
4 MAC57D5MB – Evaluation Board features
MAC57D5MB provides the following key features:
• Master Power switch and regulators status LED’s.
• High Speed CAN transceiver
• LIN interface
• Ethernet PHY and RJ45 socket configurable as RMII or MII
• 20-pin JTAG
• ARM Cortex Connector
• ART ETM Connector
• User RESET switch with reset status LED.
• User LED’s
MAC57D5MB – Evaluation Board features
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
Freescale Semiconductor, Inc. 3

• User pushbutton switches
• Potentiometer connected to analogue input channel.
• VIU Interface
• TFT Display interface with Backlight power supply for EastRising - ER-TFT050-3
• 2 Stepper Motors Connectors
Figure 2. MAC57D5MB Evaluation Board
5 Initial configuration
Initial configuration
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
4 Freescale Semiconductor, Inc.

This section details the power, reset, clocks and debug configuration and is the minimum configuration needed in order to
power on MAC57D5MB.
5.1 Main power supply
MAC57D5MB requires an external power supply voltage of 12 V, minimum 3 A. This allows the EVB to be easily used in a
vehicle if required. The 12 V input is regulated on the EVB using two switching power supplies to provide the required
voltages of 5.0 V, 3.3 V and 1.25 V in all interfaces of the Motherboard and the daughter cards.
Figure 3. Main power supply connectors
For flexibility, there are two power supply inputs, the connector and test points on the EVB which are detailed below:
Table 2. Power Supply Connectors
CONNECTOR DESCRIPTION
2.1 mm Barrel Connector P6, this connector
should be used to connect the supplied wall-plug
mains adapter.
NOTE: if a replacement or alternative adapter is
used, care must be taken to ensure the
2.1 mm plug uses the correct
polarization as shown.
Two test points PC compact RED/BLACK TP79
and TP76, these test points can be used to
connect a hook wire lead to the EVB, The
polarization of the connectors is clearly marked
on the EVB. Care must be taken to ensure
correct connection.
5.2 Power switch (SW1)
Slide switch SW1 can be used to isolate the power supply input from the EVB voltage regulators if required.
•Moving the slide switch to the left (outward of the EVB) will turn the EVB off.
• Moving the slide switch to the right (inward of the EVB) will turn the EVB on.
Initial configuration
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
Freescale Semiconductor, Inc. 5

5.3 Power jumpers of Regulators
All of the voltage regulators (switching and linear) are powered from the main 12 V supply line by a jumper with the
exception of the 3.3 V and 1.8 V linear regulator which has a two way jumper to allow selection of the input voltage. The
table below details the jumper configurations for the linear 1.25 V regulator source voltage. By default, the regulator is
powered from a 12 V supply line.
Table 3. Regulators power jumpers
BOARD REFERENCE POSITION PCB
LEGEND
DESCRIPTION
MAC57D5MB J32 1-2 (Default) - PMIC - switching regulators [5 V, 3.3 V and
1.25 V] are powered from VBAT [12 V].
REMOVED - PMIC - switching regulators [5 V, 3.3 V and
1.25 V] are not powered.
J35 1-2 (Default) - 5.0 V switching regulator output is enabled
2-3 - 5.0 V switching regulator output is disabled
REMOVED - 5.0 V switching regulator output is disabled
J36 1-2 (Default) - 3.3 V switching regulator output is enabled
2-3 - 3.3 V switching regulator output is disabled
REMOVED - 3.3 V switching regulator output is disabled
J37 1-2 (Default) - 1.25 V switching regulator output is manually
enabled
2-3 - 1.25 V switching regulator output is disabled
REMOVED - 1.25 V switching regulator output is controlled
by the MCU
J30 1-2 (Default) - 5.0 V switching regulator output is routed to
all peripherals on the EVB.
REMOVED - 5.0 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)
J26 1-2 (Default) - 3.3 V switching regulator output is routed to
all peripherals on the EVB.
REMOVED - 3.3 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)
J33 1-2 (Default) - 1.25 V switching regulator output is routed to
all peripherals on the EVB.
REMOVED - 1.25 V switching regulator output is
disconnected from all peripherals on the
EVB. (Disabled)
5.4 Power status LED’s and Fuse
Initial configuration
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
6 Freescale Semiconductor, Inc.

When power is applied to the EVB, five green LED’s adjacent to the voltage regulators show the presence of the supply
voltages as follows:
Table 4. Power status LEDs
BOARD REFERENCE DESCRIPTION
MAC57D5MB
DS2 Indicates that the 12 V is connected to the EVB correctly.
DS4 Indicates that the 5 V switching regulator is enabled and
working correctly.
DS3 Indicates that the 3.3 V switching regulator is enabled and
working correctly.
DS5 Indicates that the 1.25 V switching regulator is enabled and
working correctly.
DS1 Indicates that the TFT Display – switching regulator is
enabled and working correctly.
MAC57D5-208DC
MAC57D5-506DC DS1 Indicates that the 1.8 V switching regulator is enabled and
working correctly.
DS2 Indicates that the 0.9 V switching regulator is enabled and
working correctly.
If no LED’s are illuminated when power is applied to the EVB and the regulators are correctly enabled using the appropriate
jumpers, it is possible that either power switch SW1 is in the “OFF” position or some jumper is missed, please refer to MCU
power supply jumpers.
6 MCU power supply jumpers
Table 5. MCU power supply jumpers
BOARD REFERENCE POSITION PCB
LEGEND
DESCRIPTION
MAC57D5-208DC J2 1-2 (Default) 5.0 V switching regulator output is routed to
VDDEH_ADC_MCU and VDDA_MCU (MCU)
2-3 3.3 V switching regulator output is routed to
VDDEH_ADC_MCU and VDDA_MCU (MCU)
REMOVED VDDEH_ADC_MCU and VDDA_MCU are not
powered (disabled).
J1 1-2 (Default) 5.0 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)
2-3 3.3 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)
REMOVED VDDM_SMD_MCU is not powered (disabled).
MAC57D5-516DC J21 1-2 (Default) 3.3 V switching regulator output is routed to
VDDE_A_MCU (MCU)
REMOVED VDDE_A_MCU is not powered (disabled).
J22 1-2 (Default) 3.3 V switching regulator output is routed to
VDDE_B_MCU (MCU)
Table continues on the next page...
MCU power supply jumpers
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
Freescale Semiconductor, Inc. 7

Table 5. MCU power supply jumpers (continued)
BOARD REFERENCE POSITION PCB
LEGEND
DESCRIPTION
REMOVED VDDE_B_MCU is not powered (disabled).
J27 1-2 (Default) 3.3 V switching regulator output is routed to
VDDE_SDR_MCU (MCU)
REMOVED VDDE_SDR_MCU is not powered (disabled).
J11 1-2 (Default) 3.3 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)
2-3 5.0 V switching regulator output is routed to
VDDM_SMD_MCU (MCU)
REMOVED VDDM_SMD_MCU is not powered (disabled).
J2 1-2 (Default) 3.3 V switching regulator output is routed to
VDDEH_ADC_MCU
2-3 5.0 V switching regulator output is routed to
VDDEH_ADC_MCU
REMOVED VDDEH_ADC_MCU is not powered (disabled).
J3 1-2 (Default) 3.3 V switching regulator output is routed to
VDDA_MCU (MCU)
2-3 5.0 V switching regulator output is routed to
VDDA_MCU (MCU)
REMOVED VDDA_MCU are not powered (disabled).
J6 1-2 (Default) 3.3 V switching regulator output is routed to
VDD_HV_BALLST (MCU)
2-3 5.0 V switching regulator output is routed to
VDD_HV_BALLST (MCU)
REMOVED VDD_HV_BALLST is not powered (disabled).
J8 1-2 (Default) 1 V 25_SR switching voltage regulator is routed to
VDD12_MCU (MCU)
2-3 Output voltage of the ballast transistor is routed to
VDD12_MCU (MCU)
REMOVED VDD12_MCU is not powered (disabled).
J23 1-2 (Default) 1.8 V switching regulator output is routed to
VDDE_DDR_MCU (MCU)
REMOVED VDDE_DDR_MCU is not powered (disabled).
J18 1-2 P0V9_SR [P0V9_VTTREF] switching regulator
output is routed to VREF_DDR2_MCU and
VREF_DDR2M
2-3 (Default) Divider resistor reference (0.9 V) is routed to
VREF_DDR2_MCU and VREF_DDR2M
REMOVED VDDP9_DDR_MCU is not powered (disabled).
6.1 Peripheral power supply jumper
MCU power supply jumpers
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
8 Freescale Semiconductor, Inc.

There is an additional power supply jumper controlling the I/O voltage for the peripherals on the MAC57D5MB in the
PER_HVA voltage domain. The default configuration matches the default configuration with the jumpers set to 3.3 V.
Table 6. Peripheral power supply jumper
BOARD REFERENCE POSITION PCB
LEGEND
DESCRIPTION
MAC57D5MB J29 1-2 (Default) 3.3 V switching regulator output is routed
to PER_HVA (MCU)
2-3 5.0 V switching regulator output is routed
to PER_HVA (MCU)
REMOVED PER_HVA is not powered (disabled).
6.2 EVB voltage regulators
The following table shows the usage of each EVB voltage regulator. This provides a useful cross reference point should any
regulator be disabled.
Table 7. Voltage regulators
Regulator Used on
12 V Unregulated
P12V
All voltage regulators (switching and Linear, jumper selectable on 3.3V
linear)
LIN Interface.
3.3 V Linear
P3V3_LR
VDDA_MCU
VDDEH_ADC_MCU
MLB Interface
ADC Potentiometer
5.0 V Switcher
P5V0_SR
PER_HVA
VDDA_MCU
VDDE_A_MCU
VDDE_B_MCU
Table continues on the next page...
MCU power supply jumpers
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
Freescale Semiconductor, Inc. 9

Table 7. Voltage regulators (continued)
Regulator Used on
VDDE_SDR_MCU
VDDM_SMD_MCU
VDD_HV_BALLST
VDDEH_ADC_MCU
CAN Interface
3.3 V Switcher
P3V3_SR
VDDE_A_MCU
VDDE_B_MCU
VDDE_SDR_MCU
VDDM_SMD_MCU
VDD_HV_BALLST
Reset LED indicators
MLB Interface
TFT Display
Ethernet Interface
User LEDSs (Active Low)
User Switches (Active High)
VIU Interface
LVDS Display
DDR-II VREF and VTT Power Supply
1.8 V Switcher
P1V8_SR
VDDE_DDR_MCU
DDR2_Intarface
VIU Interface
0.9 V Switcher
P0V9_SR
VDDP9_DDR_MCU
1.25 V Switcher
1V25_SR
VDD12_MCU
7 Reset control and Oscillators
7.1 Reset circuit
The MCU has a single bi-directional open drain reset pin. There is a reset LED – D14 (Red), placed adjacent to the EVB
RESET switch to indicate the RESET status of the EVB and MCU.
Reset control and Oscillators
MAC57D5xx Customer Evaluation Boards, Rev. 0, 05/2016
10 Freescale Semiconductor, Inc.